Mercedes-Benz C-Class W206 common faults.

The wheel bolts were not tightened in accordance with the torque specifications. The bolts and the wheel assembly could detach while the vehicle is in motion, increasing the risk of accidents. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: 18/05/2026

The authority's notice

Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2022-2023 C300 and 2023 AMG C43 vehicles. The transmission wiring harness may be the incorrect length, which can result in harness damage and a loss of drive power.

Risk: A loss of drive power can increase the risk of a crash.

Remedy: Dealers will inspect and repair the transmission wiring harness routing, as necessary, free of charge. Owner notification letters were mailed August 18, 2023. Owners may contact MBUSA customer service at 1-800-367-6373. MBUSA's number for this recall is 2023070015.

The authority's notice

Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2022 C300 vehicles. Moisture accumulation in the trunk may leak into the signal acquisition module (SAM), causing an electrical short circuit.

Risk: An electrical short circuit in the SAM could lead to various malfunctions, such as rear exterior lighting failure, unintentional rear seat folding, and rearview camera failure, increasing the risk of a crash or injury. In addition, an electrical short circuit might increase the risk of a fire.

Remedy: Dealers will install a cover for the SAM, free of charge. Owner notification letters were mailed December 2, 2022. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2022090011.

The authority's notice

The vacuum-controlled coolant pump may not be tightly sealed between the coolant and vacuum circuits. This may result in the coolant leaking into the vacuum circuit leading to an electrochemical reaction, increasing the risk of fire. The product does not comply with the requirements laid down in the Regulation on the approval and market surveillance of Motor Vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

The authority's notice

Due to an incorrect material composition of the Mode 2 charging cable for charging at a household power socket, the insulation resistance of the rubber buffer could be impaired, overriding the protective function of the charging cable. Furthermore, in combination with an error in the household infrastructure, the activation of the protective device in the household electrical circuit might be prevented. This could cause the user to have an electrical shock and could lead to a fire. The product does not comply with the requirements laid down in the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

The authority's notice

The cupholder in the centre armrest of the second seat row may become detached from the armrest in the event of an accident. This could increased the risk of injury to occupants of the vehicle. The product does not comply with the requirements laid down in the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

The authority's notice

A bolt on the high-pressure pump may be faulty, which could impair the sealing function between the high-pressure pump and the tandem oil pump. As a result, oil and fuel may leak onto the road, posing a risk to the following traffic. In addition, oil and fuel could come into contact with hot engine parts, increasing the risk of fire. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

The authority's notice

Due to a faulty fixation, the rear axle wiring harness may be damaged. This may cause sudden momentum loss, increasing the risk of an accident. In addition, electrical current may cause an increased temperature in the damaged area, creating a risk of fire. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

The authority's notice

Improper foam used in the front bumper may cause the active hood release to fail to deploy in the event of a collision with a pedestrian, increasing the risk of injury. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

The authority's notice

The tank strap may not have been screwed on with the required torque, causing the screw to loosen and the fuel tank to drop, possibly hitting the drive shaft. This could damage the tank and cause fuel leaks, increasing the risk of fire. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

The authority's notice

An erroneous notch in the impact absorber may lead to failure of the tube sensor for the actuation of the active hood. In case of an accident, the active hood for pedestrian protection might be lifted too late or not at all, increasing the risk of injury to the pedestrian involved. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

The authority's notice

The bolts on the terminal clamps of the starter battery may come loose. This could increase the electrical contact resistance, leading to a local temperature increase at the terminal clamp connection point. This creates a risk of fire. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

The authority's notice

The airbag control unit may be faulty, resulting in that the PRE-SAFE function and/or the active bonnet are not activated as intended, increasing the risk of injury in case of an accident. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

The authority's notice

The rear head rests might not have been attached correctly. As a result, they could become displaced or detached from the seat in the event of an accident, increasing the risk of injury.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

The authority's notice

A fuse may be faulty, which can lead to engine failure or impairment of the restraint functions and instrument cluster. This increases the risk of an accident, injuries and fire. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

The authority's notice

The rear spoiler may be properly bonded to the tailgate and could detach, creating a risk of injuries. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

The authority's notice

Fuel may leak and the fuel line pressure may drop, leading to misfires or even engine stalling while driving, increasing the risk of an accident. Moreover, fuel leaks could pose a risk to following traffic. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

The authority's notice

Improper tyre pressure label in the tank cap may result in the tyre pressure not being identified based on the vehicle load and thus the vehicle operating with insufficient tyre pressure. As a result, the tyre may be damaged, increasing the risk of an accident. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

The authority's notice

Moisture could enter the signal acquisition and actuation module. In this case, a short circuit may occur and as a result the risk of fire increases. Moreover, this moisture may cause the exterior lighting at the rear of the vehicle to fail, the rear backseat may unintentionally fold, and the rear-view camera may not be available, increasing the risk of an accident. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

The authority's notice

Improperly connected layers of the windscreen could lead to its delamination in the event of an accident. Moreover, glass splinters could break free and impair the support of the passenger airbag. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

The authority's notice

The belt tensioner arm may have been manufactured with a borderline tolerance, which could cause one side of the V-ribbed belt to rub against the belt tensioner, causing it to fail. As a result, the coolant pump may stop working, causing the engine to overheat, thus compromising the impermeability of the oil sump. Consequently, oil may leak onto the road, posing a risk to the following traffic. The product does not comply with the requirements laid down in the Regulation on the approval and market surveillance of Motor Vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

The authority's notice

Polluted brake fluid could lead to increased wear of the braking system and a reduced braking performance. This could also impair the functioning of the electronic stability program (ESP), creating a risk of an accident. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

The authority's notice

The gearbox may be faulty. Forces and vibrations may occur when driving, which could damage the gear-shift linkage and the gearbox could disconnect from the drive shaft, causing the vehicle to lose propulsion. Moreover, components could detach from the vehicle, posing a risk to other road users. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

The authority's notice

The tightening torque on the screw connections on certain 12V and 48V ground points may be insufficient. This may lead to improper wiring fixation, which may cause rise of temperature in this area, increasing the risk of fire. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

The authority's notice

In some cases the end mount of the seat belt on the driver’s seat may not have been fitted in accordance with the specifications, for this case the end mount of the seat belt would be held in position only by the external seat trim. In the event of adverse conditions or an accident this could seriously impair the restraining function of the seat belt and increase the risk of injury to the driver. The product does not comply with the requirements laid down in the Regulation on the approval and market surveillance of Motor Vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

The authority's notice

The incorrect connection of a wiring harness to the pre-fuse box can cause a failure and increased electrical resistance. This can lead to a sudden loss of propulsion, which increases the risk of accidents and injuries. Moreover, this can increase the risk of fire in the vehicle. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

The authority's notice

Faulty welding between the fuel tank and the filler pipe can cause a fuel leak, creating a risk of fire. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

The authority's notice

The windows may not be properly attached and can fall out, creating a risk of an accident. The front airbag may not work as intended if the windscreen comes loose, increasing the risk of injury. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

The authority's notice

Ground-cable bolts may not have been tightened with sufficient torque. This can lead the wiring harness not to be properly secured and result in an increase of the connection's electrical resistance. The temperature can rise in this area, increasing the risk of fire. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

The authority's notice

The safety cap on the end mount of the seat belt of the passenger seat may not be correctly installed. The safety cap could become detached over the life of the vehicle, and the belt would no longer be fixed in its anchorage. In the event of abrupt deceleration or in the event of an accident, the belt may no longer have a restraining effect, thereby increasing the risk of accident/injury. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

The authority's notice

An improperly reworked fuse box may lead to breaks in contact or incorrect fuse ratings. Therefore, systems connected to the fuse could fail, including the vehicle losing drive without warning as well as the restraint systems or the instrument cluster being compromised. This could lead to injury or fire. The product does not comply with the requirements laid down in the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

The authority's notice

A manufacturing defect in the steering coupling may lead to loosen mechanical connection between the steering wheel and the steering box, leading to a loss of steering and increasing the risk of an accident. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

The authority's notice