BMW 2 Series 218d Gran Coupé common faults.

2020–2024, saloon, diesel, 150 HP.

The fault list covers: B47C20 engine, GA8F22AW transmission.

What you save stays on this device only. My saves

2 fault write-ups. Both are important. 9 recalls.

If you know the year, pick it. Faults for other years drop out of the list.

Before you buy

Known faults

2 important faults

B47 diesel: the timing chain stretches on the early model years

critical

On the early model years the timing chain of the B47 stretches faster than intended. The chain tensioner compensates for the stretch for a while and then no longer can: the chain jumps, the valve timing goes off, and in a severe case engine damage follows. The first sign is a rattling, clacking noise on a cold start that goes quiet after one to three seconds. On the B47 the chain sits at the front of the engine, not at the rear as on its predecessor, the N47. The replacement is therefore considerably less, between 1,200 and 1,800 euro, against 2,000 to 2,500 euro on the N47; if the chain has already jumped, the repair can run up to 4,500 euro. The risk is highest on units built before the end of 2015, with a reported rate of 3 to 5 per cent. 2016 was better but cases remained, and between July and December 2016 an improved chain tensioner was phased in. After mid-2016 the problem is rare, below one per cent. The engine has been in almost every four-cylinder diesel BMW since 2014, from the 1 Series to the 5 Series and from the X1 to the X4. The build date therefore says more here than the model.

above 120,000 km1,200–4,500 EUR

What to check

Start the engine cold and listen for the rattling noise in the first seconds
Ask for the build date, because units built before the end of 2015 are the risky ones
Ask whether the chain or the tensioner has been replaced, and ask for the invoice

2 more steps in the write-up

B47 / B57 diesel: particulate filter and turbo on short trips

critical

The B47 replaced the N47, and the maker fixed the timing chain problem. The two remaining risks on this modern diesel depend on how the car was used.

Show the rest

The first is the particulate filter. On short urban trips the regeneration cannot finish, and the filter clogs. The second is the turbo. With extended oil change intervals its bearings wear.

On this engine the service history and the type of use tell you more than the odometer. On a 200,000 km car driven on motorways and serviced often, the filter and the turbo can be in better shape than on a 90,000 km city-only car.

Where turbo wear leads in the worst case: a runaway engine. If the turbo shaft seal fails, engine oil enters the intake on the compressor side. A diesel burns that too, and this is different from a petrol engine: a diesel controls torque with the quantity of fuel injected, and it has no throttle. Once the engine runs on its own oil, cutting the injection and switching off the ignition will not stop it. The revs climb on their own until the engine destroys itself for lack of lubrication.

If this happens while driving, turning the key does not help. The only thing that works is cutting off the air: cover or plug the intake, or discharge a dry powder extinguisher into the intake tract. On a manual car you can also stall it: hold the parking brake and the brake pedal, select a high gear, and release the clutch quickly so the drivetrain chokes the engine.

This is not common, and it can happen on any turbo diesel, not only on this engine. On this engine the turbo bearing and seal wear. The warning signs are blue smoke under acceleration, an unexplained drop in oil level, and an oily charge air pipe.

What to check

Ask how the car was used: short daily trips or longer runs?
Read the fault codes for particulate filter regeneration and differential pressure
On a longer test drive watch the power delivery and the smoke under load

5 more steps in the write-up

Official recall9 recallsShow

The manufacturer fixes these for free at a franchised dealer. Ask with the VIN whether it was done.

Most recent: 30 January 2026

SR/00551/26Safety recallFire30 January 2026 · EU Safety Gate

The failure concerns the RSW22 starter, type RWT (reinforced for watertightness). Increased abrasion of the magnetic contact can lead to the formation of deposits at the lowest point of the relay interior. This in turn can increase the resistance of the relay contact, causing accidental ignition or even short circuits, possibly leading to a thermal reaction and fire. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: 30/01/2026

The authority's notice

SR/00568/26Safety recallFire30 January 2026 · EU Safety Gate

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: 30/01/2026

The authority's notice

SR/00569/26Safety recallFire30 January 2026 · EU Safety Gate

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: 30/01/2026

The authority's notice

A12/00184/24Safety recallInjuriesno date · EU Safety Gate

Due to a manufacturing error, the weld seam of the integrated transmission control unit (ITCU) may not have been correctly executed. As a result, transmission oil could leak into the ITCU, causing it to fail. This may lead to transmission seizure, increasing the risk of an accident. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.