vinkodex.

BMW 6 Series 650i xDrive Cabrio High Executive common faults.

2011–2015, convertible, petrol, 450 HP.

The fault list covers: N63B44 engine, ZF8HP70 transmission.

What you save stays on this device only. My saves

4 fault write-ups. All are important. 14 recalls.

If you know the year, pick it. Faults for other years drop out of the list.

Before you buy

Known faults

4 important faults

critical2

N63 V8: failing piezo injectors and hydraulic lock in the cylinder

critical

On this engine the injectors were also listed as parts to be replaced in the maker's own programme, which means their failure is a known one. A faulty injector puts too much fuel into the cylinder. The liquid cannot be compressed, so the piston hits it on its way up: this is hydraulic lock, and it can damage the connecting rod bearing and the connecting rod as well. The early sign is rough running and hard starting. The fault can start from 60,000 km. The maker ran a separate programme for this engine, called the Customer Care Package, from December 2014. The franchised dealers had to check seven parts: the timing chain, the fuel injectors, the mass air flow sensor, the crankcase vent lines, the battery, the vacuum pump and the low pressure fuel sensor. These had to be replaced free of charge, even if the car had already fallen out of the four-year, 50,000-mile warranty. The same programme also shortened the oil change interval: 10,000 miles or one year instead of 15,000 miles or two years. Before buying it is therefore worth asking whether this programme was carried out on the car.

above 60,000 km

What to check

  • Ask whether the Customer Care Package was carried out, and whether the injectors were replaced
  • Start the engine cold and watch for hard starting and rough running
  • Read the fault memory and look for a code reporting a misfire on a specific cylinder
2 more steps in the write-up

N63 V8: a stretching timing chain and broken guides blocking the oil system

critical

The timing chain stretches between 80,000 and 120,000 km, and the plastic chain guides break. The broken pieces end up in the sump and block the lubrication system. From then on the engine is starved of oil, which takes the bearings and the turbochargers with it. The early sign is a metallic rattling from the front of the engine on a cold start. The stretching of the chain also features in the American class actions, alongside the extreme oil consumption. The maker ran a separate programme for this engine, called the Customer Care Package, from December 2014. The franchised dealers had to check seven parts: the timing chain, the fuel injectors, the mass air flow sensor, the crankcase vent lines, the battery, the vacuum pump and the low pressure fuel sensor. These had to be replaced free of charge, even if the car had already fallen out of the four-year, 50,000-mile warranty. The same programme also shortened the oil change interval: 10,000 miles or one year instead of 15,000 miles or two years. Before buying it is therefore worth asking whether this programme was carried out on the car.

between 80,000 and 120,000 km

What to check

  • Start the engine cold and listen for metallic rattling from the front of the engine
  • Ask whether the Customer Care Package was carried out, and whether the chain was replaced
  • Read the fault memory and look for a code reporting a camshaft position deviation
2 more steps in the write-up

expensive2

N63 V8: the valve stem seals leak and oil consumption is extreme

expensive

The valve stem seals start to lose their sealing from 90,000 km, and oil gets into the combustion chamber along the valve stem. The burning oil lays soot on the piston rings, they start to stick, and from then on the consumption grows further; the lubrication also gets tighter and the exhaust smokes. The scale of the consumption on this engine is extraordinary. In the American class action the plaintiffs report around one litre every 1,200 km, and one of them one litre every 1,600 km. In 2013 the maker issued a new oil consumption standard for this engine in a bulletin, and took the position that this is not a defect: according to it every one of its engines may use that much. The lawsuit points out that with this standard the owner has to top up the oil twenty times before reaching the factory 15,000-mile oil change interval. The maker ran a separate programme for this engine, called the Customer Care Package, from December 2014. The franchised dealers had to check seven parts: the timing chain, the fuel injectors, the mass air flow sensor, the crankcase vent lines, the battery, the vacuum pump and the low pressure fuel sensor. These had to be replaced free of charge, even if the car had already fallen out of the four-year, 50,000-mile warranty. The same programme also shortened the oil change interval: 10,000 miles or one year instead of 15,000 miles or two years. Before buying it is therefore worth asking whether this programme was carried out on the car. The repair means opening the cylinder head, and because of the V layout of the engine on both sides.

above 90,000 km

What to check

  • Ask how much oil has to be added between two changes, and ask for a figure
  • Ask whether the Customer Care Package programme was carried out, and ask for the confirmation
  • Read the service book: the shortened, one-year oil change cycle is expected here
2 more steps in the write-up

ZF 8HP automatic: mechatronics unit and connector sleeve leak

expensive

The ZF eight speed automatic (BMW Steptronic 8HP family) has two faults, and you can feel both.

Show the rest

The first is the mechatronics unit: the valve body and the control electronics in one. If the solenoids or the pressure regulation weaken, the gearbox jerks, the D/R engagement is delayed, it logs a gear ratio fault code, and finally drops into limp mode (often staying in 2nd or 3rd).

The second, and often misdiagnosed, is the connector sleeve of the mechatronics unit: the O-ring of the plastic sleeve ages, and ATF leaks from the side of the housing, exactly where the wiring harness enters. This is easy to mistake for a rear crankshaft seal. The trail starts from the driver's side of the housing, not from the clutch side.

On cars built in 2023 there was also a separate safety recall for a welding fault in the mechatronics unit. That is not the same as the wear related sleeve and the valves.

Check the fluid level, the area around the sleeve and the fault codes first; do not accept a "full gearbox replacement" quote straight away.

above 120,000 km

What to check

  • On the test drive watch for delayed D/R engagement, a jerk when shifting, and limp mode (a stuck gear)
  • Look at the driver's side of the gearbox housing where the wiring harness enters: an ATF trail from the sleeve is suspect
  • Do not confuse it with a rear crankshaft seal leak: the direction of the trail decides
3 more steps in the write-up

Checklist

BMW 6 Series 650i xDrive Cabrio High Executive

First what you would check on any car. Then the faults of this model.

Before you buy

Checklist

The printed sheet starts with what you would check on any car. What you tick stays on this device only.

On every car

Ask the owner

Faults of this model

vinkodex.com · Before you buy it, see what can go wrong.

Official recall14 recallsShow

The manufacturer fixes these for free at a franchised dealer. Ask with the VIN whether it was done.

Most recent: 30 March 2023

A12/00868/23Safety recallInjuries30 March 2023 · EU Safety Gate

The airbag may deteriorate over time, and if deployed, excessive internal pressure may cause the inflator body to burst and metal fragments could pass through the cushion material causing injury to occupants. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: 30/03/2023

We could not check this: model year. The authority's notice

A12/01930/23Safety recallInjuries29 June 2021 · EU Safety Gate

The propellant in the driver airbag can deteriorate due to high humidity and temperature variations. In the event of an accident in which the airbag deploys, this could result in fragments from the inflator casing coming loose and injuring the vehicle’s occupants. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: 29/06/2021

We could not check this: model year. The authority's notice

A12/1233/17Safety recallInjuries30 August 2017 · EU Safety Gate

The front safety belts may have a faulty locking mechanism.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: 30/08/2017

We could not check this: model year. The authority's notice

12V161000ENGINE AND ENGINE COOLING:ENGINE:OTHER FUEL TYPES:TURBO/SUPERCHARGERENGINE AND ENGINE COOLING:ENGINE:OTHER FUEL TYPES:TURBO/SUPERCHARGER10 April 2012 · NHTSA (USA)

BMW IS RECALLING CERTAIN MODEL YEAR 2011 5-SERIES, 5-SERIES GRAN TURISMO, MODEL YEAR 2012 6-SERIES CONVERTIBLE, 7-SERIES, X5 SAV, AND X6 SAV VEHICLES EQUIPPED WITH 8- OR 12-CYLINDER, TURBOCHARGED, ENGINES BECAUSE THE CIRCUIT BOARD FOR THE ELECTRIC AUXILIARY WATER PUMP CAN OVERHEAT.

Risk: THIS COULD LEAD TO A SMOLDERING OF THE PUMP OR AN ENGINE COMPARTMENT OR VEHICLE FIRE.

Remedy: BMW WILL NOTIFY OWNERS, AND DEALERS WILL REPLACE THE AUXILIARY WATER PUMP FREE OF CHARGE. THE SAFETY RECALL BEGAN ON APRIL 30, 2012. OWNERS MAY CONTACT BMW CUSTOMER RELATIONS AND SERVICES AT 1-800-525-7417.

We could not check this: model year. The authority's notice

A12/00068/19Safety recallInjuriesno date · EU Safety Gate

The press-in force of the counterbalance shaft’s bearing shells may not have met the specifications, which could cause the counterbalance shaft to become loose. As a result, the engine could be damaged and locked in motion, increasing the risk of an accident.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

We could not check this: model year. The authority's notice

A12/0036/17Safety recallInjuriesno date · EU Safety Gate

The side, head and knee protection airbags of the front passenger seat may not work. This could increase the risk of injury to the occupant in the event of an accident.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

We could not check this: model year. The authority's notice

A12/00783/23Safety recallInjuriesno date · EU Safety Gate

The airbag propellant may deteriorate over time, and If deployed, excessive internal pressure may cause the inflator body to burst and metal fragments could pass through the cushion material causing injury to occupants. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

We could not check this: model year. The authority's notice

A12/01981/24Safety recallInjuriesno date · EU Safety Gate

A seam on the inflator housing of the driver airbag may not have been correctly welded. In case of accident, when the airbag is deployed, the inflator can burst, releasing metal parts which could cause injuries. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

We could not check this: model year. The authority's notice

A12/0202/17Safety recallInjuriesno date · EU Safety Gate

The universal joint of the drive shaft might break, causing a sudden loss of propulsion.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

We could not check this: model year. The authority's notice

A12/02573/24Safety recallInjuriesno date · EU Safety Gate

The propellant in the driver airbag may deteriorate over time. If the airbags deploy, it could result in fragments from the inflator injuring the vehicle's occupants. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

We could not check this: model year. The authority's notice

A12/02833/24Safety recallInjuriesno date · EU Safety Gate

The propellant in the driver airbag may deteriorate over time. If the airbags deploy, it could result in fragments from the inflator injuring the vehicle's occupants. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

We could not check this: model year. The authority's notice

A12/1147/17Safety recallInjuriesno date · EU Safety Gate

The bolt on the outside of the seat mechanism of both front seats may not have been properly secured. If the bolt comes loose, the seat can move backwards in the event of a rear-end collision accident, which would increase the risk of injury to the occupants.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

We could not check this: model year. The authority's notice

A12/1346/17Safety recallInjuriesno date · EU Safety Gate

A component of the steering mechanism might not have been fitted correctly. This might lead to considerably increased steering force being required or to a loss of steering control.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

We could not check this: model year. The authority's notice

SR/03830/25Safety recallFireno date · EU Safety Gate

Water may come into contact with the starter relay and gradually cause corrosion. This could affect the electrical connection inside the relay and make the engine difficult to start. It may also result in a short circuit and could cause the starter to overheat leading to a fire when the vehicle is in motion or when it is parked with the ignition off. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

We could not check this: model year. The authority's notice

Engine and transmission

N63B44

300–357 kW (408–485 HP) · petrol

ZF8HP70 · 8-speed automatic, longitudinal (ZF 8HP70)

automatic · 8 speed

Torque limit700 Nm
MakerZF

We built the code from the model and the gear count. The factory sheet does not state it.

Variant data

What is in this version

Factory data

Trim
650i xDrive Cabrio High Executive
Body
convertible
Fuel
petrol
Transmission
automatic
Engine size
4395 cc
Power
330 kW (449 HP)
Drive
AWD
Production
2011–2015

Factory service interval

The manufacturer specifies this for this version. Of the mileage and the time, the one that comes first is the one that counts.

  • Air filter

    • 60,000 km or 4 years

  • Cabin (pollen) filter

    • 30,000 km or 2 years

  • Brake fluid change

    • first: 3 years, then 2 years(first change at 3 years, then every two years)

  • Engine oil and oil filter (BMW condition-based service)

    • LongLife25,000 km or 2 years

  • Spark plugs, petrol

    • 60,000 km or 6 years
All F12 versions

Information, not an expert opinion

We write the descriptions, and we put the source next to them. A person reviews them before they go out. They are still information, not a technical expert opinion.

  • A fault on the list does not mean the car you are looking at has it.
  • A fault missing from the list does not mean the model is fault-free. Write-ups are made model by model. Not all of them are done.
  • You decide whether to buy. This is no substitute for an inspection. That needs a workshop and a history check.
Details in the terms