vinkodex.

BMW 7 Series 750Li xDrive common faults.

2015–2019, saloon, petrol, 450 HP.

The fault list covers: N63B44TU2 engine, ZF8HP70 transmission.

What you save stays on this device only. My saves

4 fault write-ups. All are important. 20 recalls.

If you know the year, pick it. Faults for other years drop out of the list.

Before you buy

Known faults

4 important faults

critical2

On this engine the injectors were also listed as parts to be replaced in the maker's own programme, which means their failure is a known one. A faulty injector puts too much fuel into the cylinder. The liquid cannot be compressed, so the piston hits it on its way up: this is hydraulic lock, and it can damage the connecting rod bearing and the connecting rod as well. The early sign is rough running and hard starting. The fault can start from 60,000 km. The maker ran a separate programme for this engine, called the Customer Care Package, from December 2014. The franchised dealers had to check seven parts: the timing chain, the fuel injectors, the mass air flow sensor, the crankcase vent lines, the battery, the vacuum pump and the low pressure fuel sensor. These had to be replaced free of charge, even if the car had already fallen out of the four-year, 50,000-mile warranty. The same programme also shortened the oil change interval: 10,000 miles or one year instead of 15,000 miles or two years. Before buying it is therefore worth asking whether this programme was carried out on the car.

above 60,000 km

What to check

  • Ask whether the Customer Care Package was carried out, and whether the injectors were replaced
  • Start the engine cold and watch for hard starting and rough running
  • Read the fault memory and look for a code reporting a misfire on a specific cylinder
2 more steps in the write-up

The timing chain stretches between 80,000 and 120,000 km, and the plastic chain guides break. The broken pieces end up in the sump and block the lubrication system. From then on the engine is starved of oil, which takes the bearings and the turbochargers with it. The early sign is a metallic rattling from the front of the engine on a cold start. The stretching of the chain also features in the American class actions, alongside the extreme oil consumption. The maker ran a separate programme for this engine, called the Customer Care Package, from December 2014. The franchised dealers had to check seven parts: the timing chain, the fuel injectors, the mass air flow sensor, the crankcase vent lines, the battery, the vacuum pump and the low pressure fuel sensor. These had to be replaced free of charge, even if the car had already fallen out of the four-year, 50,000-mile warranty. The same programme also shortened the oil change interval: 10,000 miles or one year instead of 15,000 miles or two years. Before buying it is therefore worth asking whether this programme was carried out on the car.

between 80,000 and 120,000 km

What to check

  • Start the engine cold and listen for metallic rattling from the front of the engine
  • Ask whether the Customer Care Package was carried out, and whether the chain was replaced
  • Read the fault memory and look for a code reporting a camshaft position deviation
2 more steps in the write-up

expensive2

The valve stem seals start to lose their sealing from 90,000 km, and oil gets into the combustion chamber along the valve stem. The burning oil lays soot on the piston rings, they start to stick, and from then on the consumption grows further; the lubrication also gets tighter and the exhaust smokes. The scale of the consumption on this engine is extraordinary. In the American class action the plaintiffs report around one litre every 1,200 km, and one of them one litre every 1,600 km. In 2013 the maker issued a new oil consumption standard for this engine in a bulletin, and took the position that this is not a defect: according to it every one of its engines may use that much. The lawsuit points out that with this standard the owner has to top up the oil twenty times before reaching the factory 15,000-mile oil change interval. The maker ran a separate programme for this engine, called the Customer Care Package, from December 2014. The franchised dealers had to check seven parts: the timing chain, the fuel injectors, the mass air flow sensor, the crankcase vent lines, the battery, the vacuum pump and the low pressure fuel sensor. These had to be replaced free of charge, even if the car had already fallen out of the four-year, 50,000-mile warranty. The same programme also shortened the oil change interval: 10,000 miles or one year instead of 15,000 miles or two years. Before buying it is therefore worth asking whether this programme was carried out on the car. The repair means opening the cylinder head, and because of the V layout of the engine on both sides.

above 90,000 km

What to check

  • Ask how much oil has to be added between two changes, and ask for a figure
  • Ask whether the Customer Care Package programme was carried out, and ask for the confirmation
  • Read the service book: the shortened, one-year oil change cycle is expected here
2 more steps in the write-up

The ZF eight speed automatic (BMW Steptronic 8HP family) has two faults, and you can feel both.

Show the rest

The first is the mechatronics unit: the valve body and the control electronics in one. If the solenoids or the pressure regulation weaken, the gearbox jerks, the D/R engagement is delayed, it logs a gear ratio fault code, and finally drops into limp mode (often staying in 2nd or 3rd).

The second, and often misdiagnosed, is the connector sleeve of the mechatronics unit: the O-ring of the plastic sleeve ages, and ATF leaks from the side of the housing, exactly where the wiring harness enters. This is easy to mistake for a rear crankshaft seal. The trail starts from the driver's side of the housing, not from the clutch side.

On cars built in 2023 there was also a separate safety recall for a welding fault in the mechatronics unit. That is not the same as the wear related sleeve and the valves.

Check the fluid level, the area around the sleeve and the fault codes first; do not accept a "full gearbox replacement" quote straight away.

above 120,000 km

What to check

  • On the test drive watch for delayed D/R engagement, a jerk when shifting, and limp mode (a stuck gear)
  • Look at the driver's side of the gearbox housing where the wiring harness enters: an ATF trail from the sleeve is suspect
  • Do not confuse it with a rear crankshaft seal leak: the direction of the trail decides
3 more steps in the write-up

Checklist

BMW 7 Series 750Li xDrive

First what you would check on any car. Then the faults of this model.

Before you buy

Checklist

The printed sheet starts with what you would check on any car. What you tick stays on this device only.

On every car

Ask the owner

vinkodex.com · Before you buy it, see what can go wrong.

Official recall20 recallsShow

The manufacturer fixes these for free at a franchised dealer. Ask with the VIN whether it was done.

Most recent: 31 August 2026

SR/02525/26Safety recallFire31 August 2026 · EU Safety Gate

Water may enter the starter motor and cause damage. As a result, the engine may no longer start, or the starter motor may short-circuit or remain continuously activated. This could cause local overheating of the starter motor or thermal overload of surrounding components and lead to a vehicle fire, including when the ignition is switched off. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: 31/08/2026

We could not check this: model year. The authority's notice

SR/02180/26Safety recallFire7 July 2026 · EU Safety Gate

The RSW22 starter with reinforced water tightness (RWT) may experience increased abrasion of the magnetic contact, causing deposits to build up at the lowest point inside the relay. These deposits may increase relay contact resistance, leading to starting failures or short circuits. If a short circuit occurs, either when attempting to start the vehicle or while driving due to vibration-related movement of the deposits, it could cause a thermal event and increase the risk of fire. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: 07/07/2026

We could not check this: model year. The authority's notice

SR/00568/26Safety recallFire30 January 2026 · EU Safety Gate

The failure concerns the RSW22 starter, type RWT (reinforced for watertightness). Increased abrasion of the magnetic contact can lead to the formation of deposits at the lowest point of the relay interior. This in turn can increase the resistance of the relay contact, causing accidental ignition or even short circuits, possibly leading to a thermal reaction and fire. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: 30/01/2026

We could not check this: model year. The authority's notice

A12/02079/23Safety recallInjuries18 August 2023 · EU Safety Gate

The welding of the front seat structure is defective. In case of an accident, the joint in question can fail and compromise the restraint system, increasing the risk of injuries. The product does not comply with the Regulation on the approval and market surveillance of Motor Vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: 18/08/2023

We could not check this: model year. The authority's notice

A12/0882/17Safety recallInjuries12 June 2017 · EU Safety Gate

Owing to a defect in the ball head of the brake pedal, the brake lights may be permanently activated, even during driving, without any error warning being shown. This might have an impact on road users following the vehicle.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: 12/06/2017

We could not check this: model year. The authority's notice

A12/0569/17Safety recallInjuries10 April 2017 · EU Safety Gate

The crimping of the engine oil cooler line may be defective and lead to the hose detaching while the vehicle is being driven, which could lead to leakage of engine oil into the engine compartment, onto the road or onto the brake discs. Oil on a brake disc could lead to critical driving conditions, particularly at higher speeds.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: 10/04/2017

We could not check this: model year. The authority's notice

A12/00068/19Safety recallInjuriesno date · EU Safety Gate

The press-in force of the counterbalance shaft’s bearing shells may not have met the specifications, which could cause the counterbalance shaft to become loose. As a result, the engine could be damaged and locked in motion, increasing the risk of an accident.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

We could not check this: model year. The authority's notice

A12/00590/21Safety recallInjuriesno date · EU Safety Gate

Defective hydraulic unit of the braking system may cause a limited braking support and increased braking distance. Moreover, in such cases the ABS system would not be available. This will lead to increased risk of an accident.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

We could not check this: model year. The authority's notice

A12/00609/21Safety recallInjuriesno date · EU Safety Gate

The ignition unit of the head airbag may separate from the inflator and enter the vehicle's interior when the airbag is deployed. As a result, the inflation of the head airbag may be reduced or non-existent, increasing the risk of injury in the event of an accident.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

We could not check this: model year. The authority's notice

A12/00996/24Safety recallInjuriesno date · EU Safety Gate

The integrated braking system could be compromised, which could lead to an unexpected failure of the hydraulic braking assistance, thereby requiring greater pressure on the brake pedal. This can result in a longer braking distance, as well as failure of the Anti-lock Braking System (ABS) and the Dynamic Stability Control (DSC), increasing the risk of an accident. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

We could not check this: model year. The authority's notice

A12/01342/20Safety recallFireno date · EU Safety Gate

A short circuit in the high-voltage battery could occur during initial charging due to a particle in the form of a welding bead. This may trigger a chain reaction in the battery, increasing the risk of fire.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

We could not check this: model year. The authority's notice

A12/01377/22Safety recallFireno date · EU Safety Gate

Defects in the winding of cell-internal foils in the high-voltage batteries can lead to the occurrence of increased self-discharge. This can cause high voltage cell modules to overheat, increasing the risk of fire. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

We could not check this: model year. The authority's notice

A12/02466/24Safety recallFireno date · EU Safety Gate

The software-based overload protection function cannot sufficiently prevent the starter being overloaded in the event of repeated long start-up attempts. The starter may overheat or sparks may be produced as a result of an increased current flow. This increases the risk of a fire. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

We could not check this: model year. The authority's notice

A12/02509/23Safety recallInjuriesno date · EU Safety Gate

The front wind-shield wipers could become stuck without warning, in any position when activated, which can decrease visibility during rain, increasing the risk of an accident. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

We could not check this: model year. The authority's notice

A12/1282/19Safety recallFireno date · EU Safety Gate

Due to inadequate screwing the high-pressure pump could become detached and fuel may leak out. This could lead to engine failure and to increased risk of the vehicle catching fire.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

We could not check this: model year. The authority's notice

A12/1346/17Safety recallInjuriesno date · EU Safety Gate

A component of the steering mechanism might not have been fitted correctly. This might lead to considerably increased steering force being required or to a loss of steering control.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

We could not check this: model year. The authority's notice

SR/00898/26Safety recallFireno date · EU Safety Gate

The cockpit cable harness may be damaged when the microfilter is replaced. This can lead to a short circuit, with smoke build-up resulting in fire. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

We could not check this: model year. The authority's notice

SR/02913/25Safety recallFireno date · EU Safety Gate

The cell modules in the vehicles concerned were not produced in accordance with the specifications, which may cause the module frame to fail. This may lead to a shutdown of the high-voltage system and fire. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

We could not check this: model year. The authority's notice

SR/03823/25Safety recallFireno date · EU Safety Gate

The engine starter’s electrical contacts may overheat and cause the vehicle to start improperly. Continued starting attempts can intensify the overheating and ignite surrounding components, potentially leading to a vehicle fire while driving or shortly after parking. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

We could not check this: model year. The authority's notice

SR/03830/25Safety recallFireno date · EU Safety Gate

Water may come into contact with the starter relay and gradually cause corrosion. This could affect the electrical connection inside the relay and make the engine difficult to start. It may also result in a short circuit and could cause the starter to overheat leading to a fire when the vehicle is in motion or when it is parked with the ignition off. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

We could not check this: model year. The authority's notice

Engine and transmission

N63B44TU2

330 kW (449 HP) · petrol

ZF8HP70 · 8-speed automatic, longitudinal (ZF 8HP70)

automatic · 8 speed

Torque limit700 Nm
MakerZF

We built the code from the model and the gear count. The factory sheet does not state it.

Variant data

What is in this version

Factory data

Trim
750Li xDrive
Body
saloon
Fuel
petrol
Transmission
automatic
Engine size
4395 cc
Power
330 kW (449 HP)
Drive
AWD
Production
2015–2019

Factory service interval

The manufacturer specifies this for this version. Of the mileage and the time, the one that comes first is the one that counts.

  • Air filter

    • 60,000 km or 4 years
  • Cabin (pollen) filter

    • 30,000 km or 2 years
  • Brake fluid change

    • first: 3 years, then 2 years(first change at 3 years, then every two years)
  • Engine oil and oil filter (BMW condition-based service)

    • LongLife25,000 km or 2 years
  • Spark plugs, petrol

    • 60,000 km or 6 years

Information, not an expert opinion

We write the descriptions, and we put the source next to them. A person reviews them before they go out. They are still information, not a technical expert opinion.

  • A fault on the list does not mean the car you are looking at has it.
  • A fault missing from the list does not mean the model is fault-free. Write-ups are made model by model. Not all of them are done.
  • You decide whether to buy. This is no substitute for an inspection. That needs a workshop and a history check.
Details in the terms