The wheel bolts were not tightened in accordance with the torque specifications. The bolts and the wheel assembly could detach while the vehicle is in motion, increasing the risk of accidents. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: 18/05/2026

We could not check this: model year. The authority's notice

Mercedes-Benz USA, LLC. (MBUSA) is recalling certain 2021 AMG GLB35, 2019-2020 A220, and 2020 GLB250 vehicles. The integral carrier that supports the front axle may corrode, causing it to fail.

Risk: Front axle carrier failure may result in a loss of steering control, increasing the risk of a crash.

Remedy: Dealers will inspect and replace the integral carrier, as necessary, free of charge. Owner notification letters were mailed July 29, 2022. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2022070009.

We could not check this: model year. The authority's notice

Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2019 A220 vehicles. Certain labels containing important information such as tire pressure may not have been installed. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 110, "Tire Selection and Rims."

Risk: If the tires are inflated to an incorrect tire pressure, the tires may be overloaded, and increase the risk of a crash.

Remedy: MBUSA will notify owners, and dealers will inspect the vehicle for the labels and apply them, as necessary, free of charge. The recall began March 26, 2021. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2021020019.

We could not check this: model year. The authority's notice

Mercedes-Benz USA, LLC. (MBUSA) is recalling certain 2019 A220 vehicles. The air conditioning condensation drain hose may not be installed properly. This may allow water to enter the driver and passenger foot wells and the center tunnel area, potentially damaging certain electrical components.

Risk: Water entering electrical components, can result in malfunctions of the supplemental restraint system (SRS), failure to start, activation of the limp-home mode while driving, and an impairment of other features, increasing the risk of injury or crash.

Remedy: MBUSA will notify owners, and dealers will inspect the air conditioning drain hose installation, correcting it if necessary, free of charge. The recall began August 31, 2020. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2020070013.

We could not check this: model year. The authority's notice

Mercedes-Benz USA, LLC. (MBUSA) is recalling certain 2019 A220 and A220 4MATIC vehicles. In certain operating conditions, the rearview camera software may cause a delay in displaying the rearview camera image. As such, these vehicles fail to comply to Federal Motor Safety Standard (FMVSS) number 111, "Rearview Mirrors."

Risk: A delayed rearview camera display can reduce the driver's view of what is behind the car, increasing the risk of a crash.

Remedy: MBUSA will notify owners, and dealers will update the rearview camera software, free of charge. The recall began April 8, 2020. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2020030018.

We could not check this: model year. The authority's notice

Mercedes-Benz USA, LLC. (MBUSA) is recalling certain 2019 A220 and A220 4MATIC vehicles. Due to improper welding, the pedal plate may bend, impairing the operation of the brake pedal.

Risk: Impaired operation of the brake pedal may increase the risk of crash.

Remedy: MBUSA will notify owners, and dealers will inspect the welding of the brake pedal, replacing it as necessary, free of charge. The recall began May 31, 2019. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2019050002.

We could not check this: model year. The authority's notice

A trapped particle may damage the sealing between the fuel rail and fuel injector, which could cause fuel to leak into the engine compartment. Consequently, leaking fuel may come into contact with hot parts of the engine, increasing the risk of fire. The product does not comply with the requirements laid down in the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

We could not check this: model year. The authority's notice

The bolts on the cross-member or the coupling device may not have been tightened with the correct torque. As a result, the cross-member could become detached from the vehicle whilst another vehicle is being towed, increasing the risk of an accident.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

We could not check this: model year. The authority's notice

A weld on the seat-height adjustment system of the left-hand front seat may be defective and can break, causing the seat cushion to tilt forward in the event of a crash. As a result, the protective effect of the restraint system will be impaired, increasing the risk of an injury.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

We could not check this: model year. The authority's notice

The four self-locking nuts used to attach the airbag might not have been correctly tightened. As a result, in the event of an accident in which the airbag was deployed, it could become detached from its base plate, failing to provide its restraining effect and increasing the risk of injuries.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

We could not check this: model year. The authority's notice

Due to inadequate corrosion protection, the integral subframe of the front axle may corrode, which could impair its operational strength and the connection of other components. This could have an impact on the steering capability of the vehicle, increasing the risk of an accident. The product does not comply with the requirements laid down in the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

We could not check this: model year. The authority's notice

The connection of the power supply to the electrical power steering may have been contaminated by heat-activated adhesive. Ageing of this adhesive could lead to a loss of clamping force and thus to a loose connection that may lead to interruption of the power supply. As a result, the electrical power steering could fail spontaneously, even while the vehicle is in motion, increasing the risk of an accident. The product does not comply with the requirements laid down in the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

We could not check this: model year. The authority's notice

The glass pane on the lifting/sliding panorama roof may not have been properly affixed. As a result, it may become completely detached, posing a risk to the following traffic.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

We could not check this: model year. The authority's notice

The right-hand bracket on the right-hand rear seat designed to attach the child seat to the ISOFIX anchor point may be missing. As a result, there would be no restraining effect provided by the ISOFIX lower anchorage system and the child seat would not be sufficiently secured, increasing the risk of injury in the event of an accident.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

We could not check this: model year. The authority's notice

Improper torque of the screws on the brake caliper housing can cause the screw connections to become loose. As a result, the braking performance would be reduced and components of the brake caliper may be lost, increasing the risk of accidents. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

We could not check this: model year. The authority's notice

The polycarbonate roof panel located between the windscreen and the panoramic roof may not have been bonded correctly to the vehicle during a prior repair. In such cases, the adhesive bonding could gradually deteriorate and the panel could become detached from the vehicle, posing a risk to other road users. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

We could not check this: model year. The authority's notice

The steering software may not correctly activate the fallback level in the event of a hardware failure. This could affect the power steering assistance and lead to the loss of steering capacity, increasing the risk of an accident. The product does not comply with the Regulation on the approval and market surveillance of Motor Vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Update of the electric steering software Date of entry into force: Unknown Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

We could not check this: model year. The authority's notice

Due to a defect in the high fuel pressure manifold the engine might be damaged. This may lead to reduced engine power and to inability to start the vehicle, increasing the risk of an accident. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.

Remedy: Type of economic operator taking notified measure(s): Importer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

We could not check this: model year. The authority's notice

A fuel pipe connection of the inerting system may be defective. As a result, it may allow fuel to leak out in the event of an accident, increasing the risk of fire.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

We could not check this: model year. The authority's notice

One of the lateral crash sensors is not attached correctly and may not record correct values in the event of a side-impact crash. As a result the lateral airbag may not be properly inflated, increasing the risk of injury to the occupants.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

We could not check this: model year. The authority's notice

The screws on the rear axle might not be tightened properly, which could lead to overloading of other screw connections. This can result in loss of wheel control and consequently to loss of control over the vehicle, increasing the risk of an accident.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

We could not check this: model year. The authority's notice

The condensed water drainage hose of the air-conditioning system may not be properly fitted. In such a case condensed water from the air conditioning system could enter the passenger compartment of the vehicle, ending up in the footwells of the driver and passenger side and in the central tunnel. As a result, any electrical components installed there could be corroded and/or subjected to short circuits or leakage currents. As a consequence, the SRS control unit could stop working, the vehicle may fail to start, the engine emergency run could be activated while driving, and the functioning of other components (e.g. the fuel pump, automatic/manual emergency call) could be adversely affected.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

We could not check this: model year. The authority's notice

The oil-supply pipe on the turbocharger may leak. As a result, engine oil could leak onto the under-body paneling and from there onto the road, posing a risk to the following traffic. Moreover, leaking engine oil might come into contact with hot components in the engine compartment, increasing the risk of fire.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

We could not check this: model year. The authority's notice

A metal chip formed during the assembly process within the ESP hydraulic unit could block a non-return valve. As a consequence, the non-return valve might no longer be able to close, affecting performance of the brake-pedal. This could increase the risk of an accident.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

We could not check this: model year. The authority's notice

The fitted tyres may not meet the load requirements and could be damaged while the vehicle is being driven. This could cause an accident and injuries. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

We could not check this: model year. The authority's notice

The flat conductor of the starter wiring has been incorrectly positioned, damaging the insulation of the flat conductor. The direct contact between the flat conductor and the car body may consequently lead to a short circuit and fire.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

We could not check this: model year. The authority's notice

The corrosion protection on the high voltage battery housing cannot be guaranteed to last for the whole lifetime of the vehicle. After the vehicle has been in use for a longer period of time, the high voltage battery housing could therefore corrode under certain specific environmental conditions. In this case, the sealing effect of the battery housing could then gradually be compromised, allowing moisture to penetrate the battery. This could lead to insulation failure, resulting in it being impossible to restart the vehicle once the engine has been switched off. Furthermore, this could increase the risk of fire. The product does not comply with the requirements laid down in the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

We could not check this: model year. The authority's notice

No perforation has been made in the outer covering of the instrument panel to enable the deployment of the passenger airbag. In the event of an accident involving deployment of the airbag at low temperatures, sharp edges could be created on the instrument panel in the airbag's deployment area, damaging the airbag. Moreover, parts of the instrument panel may become detached, increasing the risk of injury to the occupants.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

We could not check this: model year. The authority's notice

The quantity of oil in the dual-clutch gearbox may be too low or too high. This can result in impaired torque transmission, gearbox failure and potentially increased CO2 emissions. In addition, in extreme driving situations, gearbox oil might leak onto the road, posing a risk to the following traffic. Moreover, the leaking gearbox oil might come into contact with hot components, increasing the risk of fire.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

We could not check this: model year. The authority's notice

The quantity of oil in the dual-clutch gearbox may be too high. This can result in impaired torque transmission and potentially increased CO2 emissions. In addition, in extreme driving situations, gearbox oil might leak onto the road, posing a risk to the following traffic. Moreover, the leaking gearbox oil might come into contact with hot components, increasing the risk of fire.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

We could not check this: model year. The authority's notice

A bolt in the locking mechanism of the articulated trailer coupling is defective. It could break while a trailer is being towed and consequently the trailer could detach, thus increasing the risk of an accident for following traffic.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

We could not check this: model year. The authority's notice

The locking mechanisms of the right and/or left backrest might not lock correctly. This might impair the restraining effect of the backrest so that in the event of an accident there would be an increased risk of injury to the occupants.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

We could not check this: model year. The authority's notice

The pyrofuse casing may move while the vehicle is in motion, potentially damaging cables. As a result, the pyrofuse could fail during an accident or cause the separator piston to dislodge into the driver’s footwell, increasing the risk of injury. Additionally, in plug-in hybrid and electric vehicles, cable damage could lead to high-voltage system failure and loss of power without warning, increasing the risk of an accident. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

We could not check this: model year. The authority's notice

The casing material of the gas generator of the driver airbag may be defective. In the event that the airbag is deployed, the airbag may not protect the driver and detached parts might enter the passenger compartment causing injury to the vehicle occupants.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

We could not check this: model year. The authority's notice

Certain welding points in the area of the front wheel arch may be missing. If these welding points are not present, the structural behaviour of the vehicle's front section would be affected in the event of a crash.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

We could not check this: model year. The authority's notice

The welding of the mounting brackets on the ISOFIX child seat attachments may be inadequate. The mounting brackets could fail in the event of an accident.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

We could not check this: model year. The authority's notice

The welding of the brake pedal plate to the brake pedal lever may not be sufficiently strong. Applying pressure on the left side of the brake pedal might cause the pedal plate to tilt sideways from the pedal lever. This would impair the operation of the brake pedal, increasing the risk of an accident.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

We could not check this: model year. The authority's notice

The navigation software may be faulty, storing the wrong location of the vehicle. As a result, when the emergency call system (eCall) is used, the location communicated to the emergency centre might not correspond to the current vehicle location. In such cases, emergency services would not be correctly directed to the vehicle.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

We could not check this: model year. The authority's notice

Due to manufacturing according to wrong specifications, there might be inclusions or cracks in the camber strut connection of the right-hand wheel carrier on the rear axle. Consequently, under specific stresses the wheel carrier could break at the camber strut connection, affecting the wheel control and vehicle stability, increasing the risk of accidents.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

We could not check this: model year. The authority's notice

The belt anchor fittings for the front seats may not have been attached in accordance with the specifications. As a result, the anchor fittings could be detached in the event of an accident, increasing the risk of an injury to the occupants.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

We could not check this: model year. The authority's notice

The air-conditioning system's condensed-water drainage hose may be blocked, which may cause water to enter into the vehicle's interior. Consequently, any electrical components installed there could be corroded and/or subjected to short circuits or leakage currents. As a result, the Supplemental Restraint System (SRS) control unit could stop working, the vehicle may fail to start, the engine emergency run could be activated while the vehicle is in motion, and the functioning of other components (e.g. the fuel pump, automatic/manual emergency call) could be adversely affected. This would increase the risk of injury and accident.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

We could not check this: model year. The authority's notice

A gasket is lacking between the exhaust manifold and the exhaust gas turbocharger. This can lead to hot, unpurified exhaust gas seeping out between the turbocharger and the manifold. This can damage the cylinder head cover and cause an oil leak. If the oil come into contact with hot engine parts, the vehicle can catch fire. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

We could not check this: model year. The authority's notice

The length of the brake hoses on the rear axle is incorrect. The rear axle’s brake hoses can come into contact with surrounding components, chafe over time, and leak brake fluid. This can lead to reduced braking performance in one of the two brake circuits and increase the risk of accidents and injuries. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

We could not check this: model year. The authority's notice

A washer for the front safety belts may not correspond to specifications and could not withstand the loads. In the event of an accident, the restraining effect could be incomplete, increasing the risk of injuries. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

We could not check this: model year. The authority's notice