A12/00045/22Safety recallFireno date · EU Safety Gate
The vacuum-controlled coolant pump may not be tightly sealed between the coolant and vacuum circuits. This may result in the coolant leaking into the vacuum circuit leading to an electrochemical reaction, increasing the risk of fire. The product does not comply with the requirements laid down in the Regulation on the approval and market surveillance of Motor Vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
Remedy: Type of economic operator taking notified measure(s): Manufacturer
Category of measure(s): Recall of the product from end users
Date of entry into force: Unknown
The authority's notice
A12/00323/21Safety recallFireno date · EU Safety Gate
The maximum permissible operating temperature of individual diodes on the alternator rectifier bridge could be exceeded and the diodes could subsequently fail.
Consequently, an improper flow of current from the on-board electrical system battery through the alternator to the vehicle earth could occur.
As a result, the windings in the alternator stator could be heated to such an extent that an outbreak of fire cannot be ruled out.
Remedy: Type of economic operator taking notified measure(s): Manufacturer
Category of measure(s): Recall of the product from end users
Date of entry into force: Unknown
The authority's notice
A12/00669/21Safety recallFire, Injuriesno date · EU Safety Gate
Faulty connection of the inerting system’s gas pipes could impair the intended distribution of argon shielding gas to the points where there could be contact between the leaking refrigerant R1234yf and hot engine components in the event of an accident.
This would reduce the cooling effect of the inerting gas, leading to increased risk of fire.
Remedy: Type of economic operator taking notified measure(s): Manufacturer
Category of measure(s): Recall of the product from end users
Date of entry into force: Unknown
The authority's notice
A12/00902/20Safety recallInjuriesno date · EU Safety Gate
The brake discs installed on the front axle may be too small (in diameter and thickness) and would not sit symmetrically in the brake calliper.
As a result, the brake lining can wear out and a gap between the piston and the sealing ring can be formed, allowing brake fluid to leak out.
This will impair the braking performance, increasing the risk of an accident.
Remedy: Type of economic operator taking notified measure(s): Manufacturer
Category of measure(s): Recall of the product from end users
Date of entry into force: Unknown
The authority's notice
A12/01178/20Safety recallInjuriesno date · EU Safety Gate
The ESP control unit software does not comply with the specifications and may not be able to adapt to the type of brakes installed.
This can cause the ESP system to be unable to respond as intended to a possible drift of the yaw rate sensor or to a failure of the brake vacuum supply.
As a result, the ESP intervention may be inappropriate to the driving situation, increasing the risk of an accident.
Remedy: Type of economic operator taking notified measure(s): Manufacturer
Category of measure(s): Recall of the product from end users
Date of entry into force: Unknown
The authority's notice
A12/01336/20Safety recallFire, Injuriesno date · EU Safety Gate
Due to the lack of documentation, there is no confirmation that the screw connections of the turbocharger’s oil-supply and oil-return pipes were correctly executed during the assembly process.
In the event of a loose screw connection, oil might leak at the oil-supply and/or oil-return pipe of the turbocharger.
The leaking oil might then come into contact with hot components, increasing the risk of fire.
Remedy: Type of economic operator taking notified measure(s): Manufacturer
Category of measure(s): Recall of the product from end users
Date of entry into force: Unknown
The authority's notice
A12/0135/19Safety recallInjuriesno date · EU Safety Gate
The steering wheel may not be correctly connected with the steering gearbox. This could lead to loss of steering of the vehicle increasing the risk of accident.
Remedy: Type of economic operator taking notified measure(s): Manufacturer
Category of measure(s): Recall of the product from end users
Date of entry into force: Unknown
The authority's notice
A12/01532/21Safety recallInjuriesno date · EU Safety Gate
The belt tensioner arm may have been manufactured with a borderline tolerance, which could cause one side of the V-ribbed belt to rub against the belt tensioner, causing it to fail.
As a result, the coolant pump may stop working, causing the engine to overheat, thus compromising the impermeability of the oil sump. Consequently, oil may leak onto the road, posing a risk to the following traffic. The product does not comply with the requirements laid down in the Regulation on the approval and market surveillance of Motor Vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
Remedy: Type of economic operator taking notified measure(s): Manufacturer
Category of measure(s): Recall of the product from end users
Date of entry into force: Unknown
The authority's notice
A12/01557/21Safety recallInjuriesno date · EU Safety Gate
In certain GLE/GLS (BR 167) and C-class vehicles, the seats might be constructed incomplete or with unintended trim, increasing the risk of injury in the event of an accident. The product does not comply with the requirements laid down in the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
Remedy: Type of economic operator taking notified measure(s): Manufacturer
Category of measure(s): Recall of the product from end users
Date of entry into force: Unknown
The authority's notice
A12/0163/19Safety recallInjuriesno date · EU Safety Gate
In vehicles with automatic child-seat detection, the status shown in the centre console of the passenger airbags may not be correctly indicated. In this case, the vehicle users would not be correctly informed of the actual activation status of the passenger airbag and may not react appropriately to a potentially false passenger classification, thereby increasing the risk of injury for passengers in the event of an accident.
Remedy: Type of economic operator taking notified measure(s): Manufacturer
Category of measure(s): Recall of the product from end users
Date of entry into force: Unknown
The authority's notice
A12/0164/19Safety recallInjuriesno date · EU Safety Gate
There may be cracks in a securing nut in the steering gear of rear-wheel-drive vehicles. The nut could consequently break if the steering system is subject to a very high lateral force, which could result in rotating parts in the steering gear affecting the casing and thereby blocking the steering system.
Remedy: Type of economic operator taking notified measure(s): Manufacturer
Category of measure(s): Recall of the product from end users
Date of entry into force: Unknown
The authority's notice
A12/0220/19Safety recallInjuriesno date · EU Safety Gate
A defective sensor installed within the electrical power steering system may lead to deactivation of the power steering assistance. As a consequence, there is an increased risk of accidents.
Remedy: Type of economic operator taking notified measure(s): Manufacturer
Category of measure(s): Recall of the product from end users
Date of entry into force: Unknown
The authority's notice
A12/0268/19Safety recallInjuriesno date · EU Safety Gate
The sensors in some seatbelt locks may not have been adequately manufactured. Consequently, they might not detect a correctly fastened seatbelt and thus not activate the pre-tensioner systems (electric and pyrotechnic). In the event of an accident, these might not work leading to a limited restraint capacity and increasing the risk of injury to the occupants.
Remedy: Type of economic operator taking notified measure(s): Manufacturer
Category of measure(s): Recall of the product from end users
Date of entry into force: Unknown
The authority's notice
A12/0296/19Safety recallInjuriesno date · EU Safety Gate
In vehicles with rear-wheel drive, a lock nut in the steering gear may be cracked. Consequently, when the steering is placed under high forces it could break, which would block the steering gear and increase the risk of accident.
Remedy: Type of economic operator taking notified measure(s): Manufacturer
Category of measure(s): Recall of the product from end users
Date of entry into force: Unknown
The authority's notice
A12/0685/19Safety recallInjuriesno date · EU Safety Gate
The sleep mode functionality of the electronic parking brake within the electronic stability programme (ESP) software may be defective. As a result, the brake lights may be permanently activated or the ESP function could be deactivated, increasing the risk of an accident.
Remedy: Type of economic operator taking notified measure(s): Manufacturer
Category of measure(s): Recall of the product from end users
Date of entry into force: Unknown
The authority's notice
A12/0775/18Safety recallInjuriesno date · EU Safety Gate
The welding of the backrests of the driver's and front passenger's seats may be defective. In the event of an accident, the welding could break, increasing the risk of injury to the occupant of the seat in question.
Remedy: Type of economic operator taking notified measure(s): Manufacturer
Category of measure(s): Recall of the product from end users
Date of entry into force: Unknown
The authority's notice
A12/0852/18Safety recallInjuriesno date · EU Safety Gate
The casing material of the gas generator of the driver airbag may be defective. In the event that the airbag is deployed, the airbag may not protect the driver and detached parts might enter the passenger compartment causing injury to the vehicle occupants.
Remedy: Type of economic operator taking notified measure(s): Manufacturer
Category of measure(s): Recall of the product from end users
Date of entry into force: Unknown
The authority's notice
A12/1130/19Safety recallFireno date · EU Safety Gate
The fixing screws for the turbocharger oil return line and the crankcase breather pipe may have been interchanged. Due to a screw being too long, the pre-tensioning force of the screw connection may be insufficient and oil could leak from the turbocharger oil return line. As a result, oil could come into contact with hot components, increasing the risk of fire.
Remedy: Type of economic operator taking notified measure(s): Manufacturer
Category of measure(s): Recall of the product from end users
Date of entry into force: Unknown
The authority's notice
A12/1382/18Safety recallFireno date · EU Safety Gate
The lower engine compartment cover lacks the necessary left-hand gap for the exhaust system. As a result, the exhaust system temperatures resulting from operation at full load could lead to the cover catching fire.
Remedy: Type of economic operator taking notified measure(s): Manufacturer
Category of measure(s): Recall of the product from end users
Date of entry into force: Unknown
The authority's notice
A12/1554/19Safety recallInjuriesno date · EU Safety Gate
The bolts which connect the cross-member of the trailer coupling device (towbar) to the vehicle may not have been tightened with the correct torque. As a result, the cross-member and the trailer could be completely detached from the vehicle, endangering the following traffic and increasing the risk of an accident.
Remedy: Type of economic operator taking notified measure(s): Manufacturer
Category of measure(s): Recall of the product from end users
Date of entry into force: Unknown
The authority's notice
A12/1794/19Safety recallInjuriesno date · EU Safety Gate
The fixing screw connecting the base holder of the manual control device may not be correctly fitted. This can impair the control over the vehicle, increasing the risk of an accident.
Remedy: Type of economic operator taking notified measure(s): Manufacturer
Category of measure(s): Recall of the product from end users
Date of entry into force: Unknown
The authority's notice
