15V505000ENGINE AND ENGINE COOLING:ENGINEENGINE AND ENGINE COOLING:ENGINE11 August 2015 · NHTSA (USA)
Mercedes-Benz USA, LLC (MBUSA) is recalling certain model year 2016 Mercedes Benz E350, E400, E400 4Matic, E63 4M S AMG, E350 4Matic, E63-4M S AMG, 2015 CLS400, CLS400 4Matic, CLS550, CLS63-4M "P" AMG, and CLS550 4Matic vehicles manufactured April 16, 2015, to April 22, 2015. The integral steel cable that secures the rubber seal to the bulkhead might have been damaged due to the supplier rework of the rubber seal. In the event the rubber seal is not properly secured around the engine compartment, it is possible for the rubber seal to temporarily stick to the hood when it is opened and then may fall into the engine bay when the hood is closed.
Risk: If the rubber seal falls into the engine compartment, it may contact parts of the engine or exhaust system, increasing the risk of a fire.
Remedy: MBUSA will notify owners, and dealers will replace the rubber seal, in the engine compartment, free of charge. The recall began on September 2, 2015. MBUSA's number is 2015080001. Owners may contact MBUSA customer service at 1-201-573-5339.
The authority's notice
A12/00017/22Safety recallFireno date · EU Safety Gate
A trapped particle may damage the sealing between the fuel rail and fuel injector, which could cause fuel to leak into the engine compartment.
Consequently, leaking fuel may come into contact with hot parts of the engine, increasing the risk of fire. The product does not comply with the requirements laid down in the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
Remedy: Type of economic operator taking notified measure(s): Manufacturer
Category of measure(s): Recall of the product from end users
Date of entry into force: Unknown
The authority's notice
A12/01236/20Safety recallInjuriesno date · EU Safety Gate
The driver and passenger airbags of the company Takata in vehicles with ammonium nitrate gas generators without drying agents could, under certain climate conditions, lead over time to a chemical change in the fuel.
In the event of an accident triggering the release of the driver or passenger airbag, this change could cause the gas generators to burst. If a gas generator ruptures, the airbag would then have no restraining function and loose parts from the gas generator could reach the vehicle interior. This would increase the risk of injury for passengers.
Remedy: Type of economic operator taking notified measure(s): Manufacturer
Category of measure(s): Recall of the product from end users
Date of entry into force: Unknown
The authority's notice
A12/0334/17Safety recallInjuriesno date · EU Safety Gate
The front passenger occupant detection control unit may have been incorrectly installed and could misclassify a passenger as a child seat. That would cause the front passenger airbag to be deactivated in the event of an accident and would thereby increase the risk of injury for the passenger.
Remedy: Type of economic operator taking notified measure(s): Manufacturer
Category of measure(s): Recall of the product from end users
Date of entry into force: Unknown
The authority's notice
A12/0457/17Safety recallInjuriesno date · EU Safety Gate
Following the update of the control unit coding, the coding parameters of the control unit could be defective. This could give rise to various unplanned reactions in the vehicle: the wrong airbag could be triggered in the event of an accident, the airbag control unit may not recognise the belt buckle status, the engine control unit could be coded with a false maximum speed or various assistance systems may not function.
Remedy: Type of economic operator taking notified measure(s): Manufacturer
Category of measure(s): Recall of the product from end users
Date of entry into force: Unknown
The authority's notice
A12/0626/17Safety recallInjuriesno date · EU Safety Gate
The propellant mixing ratio in certain seat-belt pre-tensioner igniters may be incorrect. As a result, in the event of an accident where the front seat-belt pre-tensioners are activated, the pre-tensioners would not provide the restraint performance required if the igniter did not ignite as intended. This could put the occupants at a greater risk of injury.
Remedy: Type of economic operator taking notified measure(s): Manufacturer
Category of measure(s): Recall of the product from end users
Date of entry into force: Unknown
The authority's notice
A12/0763/17Safety recallInjuriesno date · EU Safety Gate
The mixture ratio of the fuel in the inflators of the front-passenger knee, pelvic and side curtain airbags may not be correct. In the event of an accident requiring the deployment of the airbags, this could lead to the airbags not inflating properly.
Remedy: Type of economic operator taking notified measure(s): Manufacturer
Category of measure(s): Recall of the product from end users
Date of entry into force: Unknown
The authority's notice
A12/0837/17Safety recallInjuriesno date · EU Safety Gate
The bonding between the top and the lower part of the roof-mounted taxi sign may not be adequate. As a consequence, the top of the taxi sign may become detached from the lower part with a risk of accidents for other road users.
Remedy: Type of economic operator taking notified measure(s): Manufacturer
Category of measure(s): Recall of the product from end users
Date of entry into force: Unknown
The authority's notice
A12/1259/17Safety recallInjuriesno date · EU Safety Gate
The mixing ratio of the propellant for the seat-belt pre-tensioner igniters may be incorrect. In an accident in which the rear seat-belt pre-tensioners were activated, the igniters might not ignite as intended and the pre-tensioners would not provide the restraint performance required.
Remedy: Type of economic operator taking notified measure(s): Manufacturer
Category of measure(s): Recall of the product from end users
Date of entry into force: Unknown
The authority's notice
A12/1608/18Safety recallInjuriesno date · EU Safety Gate
The operation of the active bonnet may be faulty because of a wrong positioning of the sensor hose in the front bumper. In the event of a collision with a pedestrian, the pedestrian would not be detected and the active bonnet would not be triggered. This could increase the potential risk of injury for the pedestrian.
Remedy: Type of economic operator taking notified measure(s): Manufacturer
Category of measure(s): Recall of the product from end users
Date of entry into force: Unknown
The authority's notice
A12/1753/19Safety recallInjuriesno date · EU Safety Gate
The rear spoiler might not have been attached in accordance with requirements. As a result, the rear spoiler could become completely detached from the vehicle at high speeds, posing a risk to the following traffic.
Remedy: Type of economic operator taking notified measure(s): Manufacturer
Category of measure(s): Recall of the product from end users
Date of entry into force: Unknown
The authority's notice
SR/03711/24Safety recallInjuriesno date · EU Safety Gate
The three aluminium screws of the steering box may corrode due to exposure to spray water and aggressive road-grit (salt) used for melting ice. Advanced corrosion could weaken the screws, leading to potential breakage during manoeuvring or parking. If all fixing screws fail, the power-assisted steering could detach, resulting in a loss of power steering and an increased risk of an accident. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
Remedy: Type of economic operator taking notified measure(s): Manufacturer
Category of measure(s): Recall of the product from end users
Date of entry into force: Unknown
The authority's notice
