vinkodex.

Mercedes-Benz E-Class E 200 BlueEFFICIENCY Avantgarde common faults.

2009–2013, saloon, petrol, 184 HP.

The fault list covers: M271DE18AL engine, MB7229 transmission.

What you save stays on this device only. My saves

4 fault write-ups. All are important. 6 recalls.

If you know the year, pick it. Faults for other years drop out of the list.

Before you buy

Known faults

4 important faults

critical2

M271, M272, M273: a leaking camshaft adjuster magnet and oil in the wiring harness

critical

The solenoid of the camshaft adjuster is sealed from the factory by nothing more than a plain sealing ring, and over time that starts to leak. The maker's own bulletin names two places: if the leak is between the solenoid and the cylinder head, the sealing ring has to be replaced, and if it comes through the electrical connector, then the solenoid itself.

Show the rest

The more serious trouble is at the connector. Through it the engine oil gets into the engine wiring harness and travels under the insulation by capillary action, so it reaches the engine control unit and other important parts as well. The loss of the control unit is the end of that road, and serious engine damage can follow; alongside the contaminated harness the most varied fault messages can appear. Cases have been reported where the oil ran out of the connector, and the consequential damage after that was already large.

The check is simple: the connector of the solenoid has to be taken off and looked at to see whether it is oily. In the fault memory a faulty solenoid gives one of the codes 0059, 0060, 0063, 0064, 0271, 0272, 0275 and 0276. One thing is worth knowing: according to the maker only the solenoid that has a corresponding code has to be replaced, so if a workshop has changed all four of them alongside two codes, that is worth asking about.

The engine number decides what is in the car. Above engine number 2729..30 759427 (M272) and 2739..30 193592 (M273) the maker already fitted the improved solenoid, under part number A272 051 01 77. The oil-leaking solenoid is a problem on engine numbers below 2729..30 895140 and 2739..30 236360.

The prevention is the oil stop cable, which has to be fitted between the solenoid and the harness: the two wires contain a sealed copper sleeve covered with heat-shrink tubing, and that stops the oil from travelling further. It is available from the factory and is not expensive: the two solenoids were around 33 euros and the two oil stop cables around 31 euros, while replacing the control unit is a four-figure sum.

between 90,000 and 130,000 kmfrom 31 EUR

What to check

  • Ask whether an oil stop cable has been fitted between the camshaft solenoids and the harness
  • Ask for a check: taking the connector off the solenoid shows whether it is oily
  • Read the fault memory and look for codes 0059, 0060, 0063, 0064, 0271, 0272, 0275 and 0276
3 more steps in the write-up

M271 1.8: stretching timing chain and worn camshaft adjuster

critical

On the four cylinder, supercharged 1.8 M271 the timing chain stretches and the sprockets of the camshaft adjuster (Nockenwellenversteller) wear out. The two go together: a stretched chain makes the adjuster work worse, and a worn adjuster loads the chain further.

Show the rest

The symptom shows up on a cold start first: a short, metallic rattle or knock from the front of the engine that quietens after a few seconds. Later an engine warning light and timing control fault codes join it.

In the official complaint database the four cylinder M271 model group (C 180/200/230/250, E 200, SLK 200/250, GLK 250, CLS 250) has 16 reports between 2008 and 2015, and 8 of those carry a mileage. The raw numbers fall between 61,000 and 152,000 km, from eight reports.

All 16 reports fall on the 2012 to 2014 model years of the C 250. The complaint texts repeatedly mention the maker's extended warranty.

On a warm engine the rattle cannot be heard.

reported complaints only

What to check

  • Start it cold: the chain rattle is audible in the first few seconds and disappears once warm
  • Do not accept the seller bringing the car warmed up; ask them to start it from standing, cold
  • Ask for a fault code read: timing control and camshaft position codes
3 more steps in the write-up

expensive2

7G-Tronic (722.9): mechatronics and conductor plate

expensive

In the Mercedes 7 speed 722.9 automatic (7G-Tronic / 7G-Tronic Plus) the mechatronics unit and the conductor plate (Leiterplatte) age over time: jerking on shifts, delayed engagement, a "Getriebe schützen" message, and fault codes on the gearbox electronics.

Show the rest

The repair is typically replacing the mechatronics unit or the conductor plate together with an oil change: not the whole gearbox. The complaint is most common on the longitudinal platforms from around 2005 to 2015 (C/E/ML and the early GLC).

The 9G-Tronic (725.0) is a different design; this applies only to the 7G.

between 100,000 and 220,000 km

What to check

  • Try it cold and warm: a delayed 1 to 2 or 2 to 3 shift is suspect
  • Watch for the gearbox warning or the "Getriebe schützen" message on the dash
  • Ask for a fault code read on the gearbox controller (not just the engine codes)
1 more steps in the write-up

Airmatic air suspension: leaking air spring, overworked compressor

expensive

The Mercedes Airmatic system holds the ride height with air springs and electronically controlled dampers. The most common faults over time are the relay, the compressor and a leaking air spring or air line.

Show the rest

The rear air springs of the 2003 to 2009 E-Class (W211) are particularly prone to leaking along the clamps. If the system leaks, the compressor runs continuously, overheats and fails, so an unrepaired leak takes the compressor with it.

Symptoms: one corner of the car sinks by morning, an "Air Suspension" or level control fault message, and compressor noise while standing. It was an option (or standard) across several generations from the W220 S-Class onwards; the estate E-Class often has air springs with level control on the rear axle as standard.

between 100,000 and 220,000 km

What to check

  • In the morning, before setting off, look at all four corners: an uneven stance means a suspected leak
  • With the car standing, listen to the compressor: continuous running indicates it is overworked
  • Ask for a fault code read on the suspension controller (level and pressure sensor codes of the C1132 / C1144 kind)
3 more steps in the write-up

Checklist

Mercedes-Benz E-Class E 200 BlueEFFICIENCY Avantgarde

First what you would check on any car. Then the faults of this model.

Before you buy

Checklist

The printed sheet starts with what you would check on any car. What you tick stays on this device only.

On every car

Ask the owner

Faults of this model

vinkodex.com · Before you buy it, see what can go wrong.

Official recall6 recallsShow

The manufacturer fixes these for free at a franchised dealer. Ask with the VIN whether it was done.

Most recent: 13 August 2021

21V638000AIR BAGS:FRONTALAIR BAGS:FRONTAL13 August 2021 · NHTSA (USA)

Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2015-2016 E400 Coupe, 2012-2015 C250 Coupe, C350 Coupe, C63 AMG Coupe, 2011-2014 E350 Coupe, and 2012-2014 E350 Cabrio vehicles. An incorrect front passenger air bag may have been installed during a prior repair.

Risk: An incorrect air bag may not function properly in a crash, increasing the risk of injury.

Remedy: Dealers will replace the front passenger air bag on the affected vehicles, free of charge. Owner notification letters were mailed on September 10, 2021. Owners may contact MBUSA customer service at 1-800-367-6372.

The authority's notice

18V043000AIR BAGS:FRONTAL:PASSENGER SIDE:INFLATOR MODULEAIR BAGS:FRONTAL:PASSENGER SIDE:INFLATOR MODULE10 January 2018 · NHTSA (USA)

Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2013 C250, C250 Coupe, C350 Coupe 4Matic, C300 4Matic, C350, C350 Coupe, C63 AMG, C63 Coupe, E350 Cabrio, E350 Coupe, E550 Cabrio, E350 Coupe 4Matic, E550 Coupe, GLK350 4Matic, GLK250 Bluetec 4Matic, GLK350, SLS Coupe, SLS AMG GT Coupe, and SLS Roadster vehicles sold, or ever registered, in the states of Alabama, California, Florida, Georgia, Hawaii, Louisiana, Mississippi, South Carolina, Texas, Puerto Rico, American Samoa, Guam, the Northern Mariana Islands (Saipan), and the U.S. Virgin Islands or "Zone A." Additionally, MBUSA is recalling certain 2010 C300, C300 4Matic, C63 AMG, E350 Coupe, E550 Coupe, GLK350, and GLK350 4Matic vehicles ever registered in the states of Arizona, Arkansas, Delaware, District of Columbia, Illinois, Indiana, Kansas, Kentucky, Maryland, Missouri, Nebraska, Nevada, New Jersey, New Mexico, North Carolina, Ohio, Oklahoma, Pennsylvania, Tennessee, Virginia, and West Virginia or "Zone B." MBUSA is also recalling certain 2009 C300, C300 4Matic, C63 AMG, and C350 vehicles ever registered in the states of AK, CO, CT, ID, IA, ME, MA, MI, MN, MO, NH, NY, ND, OR, RI, SD, UT, VT, WA, WI and WY or "Zone C." In the event of a crash necessitating deployment of the passenger frontal air bag, these passenger air bag inflator may explode due to propellant degradation occurring after long-term exposure to absolute humidity and temperature cycling.

Risk: An inflator explosion may result in sharp metal fragments striking the driver or other occupants resulting in serious injury or death.

Remedy: MBUSA will notify owners, and dealers will replace the passenger frontal air bag module, free of charge. Mercedes issued an interim notification to owners on February 23, 2018. A second notice will be mailed when remedy parts are available. Owners may contact MBUSA customer service at 1-877-496-3691.

The authority's notice

16V363000AIR BAGS:FRONTAL:PASSENGER SIDE:INFLATOR MODULEAIR BAGS:FRONTAL:PASSENGER SIDE:INFLATOR MODULE26 May 2016 · NHTSA (USA)

Mercedes-Benz USA, LLC (MBUSA) is recalling certain model year 2008-2011 C300 Sedan, C300 4matic Sedan, C350 Sedan, C63 AMG Sedan vehicles, 2010-2011 GLK350, GLK350 4-Matic and E350 Coupe vehicles, 2011 SLS AMG, E350 Convertible, E550 Coupe and E550 Convertible vehicles originally sold, or ever registered, in Alabama, California, Florida, Georgia, Hawaii, Louisiana, Mississippi, South Carolina, Texas, Puerto Rico, American Samoa, Guam, the Northern Mariana Islands (Saipan), and the U.S. Virgin Islands, or "Zone A." Additionally, unless included in "Zone A" above, MBUSA is recalling certain model year 2008 C300 Sedan, C350 Sedan, C63 AMG Sedan and C300 4-Matic Sedan vehicles originally sold, or ever registered, in Arizona, Arkansas, Delaware, District of Columbia, Illinois, Indiana, Kansas, Kentucky, Maryland, Missouri, Nebraska, Nevada, New Jersey, New Mexico, North Carolina, Ohio, Oklahoma, Pennsylvania, Tennessee, Virginia, and West Virginia, or "Zone B." Vehicles not originally sold or ever registered in either Zones A or B are not subject to this safety recall. These vehicles are equipped with certain air bag inflators assembled as part of the passenger frontal air bag modules, and used as original equipment or replacement equipment. In the event of a crash necessitating deployment of the front air bags, these inflators may rupture due to propellant degradation occurring after long-term exposure to absolute humidity and temperature cycling.

Risk: An inflator rupture may result in metal fragments striking the vehicle occupants resulting in serious injury or death.

Remedy: MBUSA will notify owners, and dealers will replace the passenger frontal air bag modules, free of charge. Owners were sent an interim notification October 2016. A second notice will be mailed when remedy parts are available. Owners may contact MBUSA customer service at 1-877-496-3691.

The authority's notice

16V081000AIR BAGS:FRONTAL:DRIVER SIDE:INFLATOR MODULEAIR BAGS:FRONTAL:DRIVER SIDE:INFLATOR MODULE11 February 2016 · NHTSA (USA)

Mercedes-Benz USA, LLC. (MBUSA) is recalling certain model year 2009-2010 ML320 BlueTec 4Matic, GL320 BlueTec 4Matic and R320 CDI 4Matic, 2011 E350 Cabriolet and E550 Cabriolet, 2009-2011 ML350, ML350 4Matic, ML550 4Matic, ML63 AMG, and C63 AMG, 2010-2011 ML450 4Matic Hybrid, E350 Coupe, E350 4Matic, E550 Coupe, E550 4Matic, and E63 AMG, 2011-2012 GL350 BlueTec 4Matic and R350 BlueTec 4Matic, 2009-2012 GL450 4Matic, GL550 4Matic and R350 4Matic, 2007-2008 SLK280, SLK350, and SLK55 AMG, 2011-2014 SLS AMG Coupe, 2012 SLS AMG Cabriolet, 2013-2014 SLS AMG GT and SLS AMG GT Cabriolet, 2005 C230 Kompressor and C320, 2006-2007 C230, 2006-2011 C350, 2008-2011 C300 and C300 4Matic, 2010-2012 GLK350 and GLK350 4Matic and 2007-2008 Chrysler Crossfire vehicles. Upon deployment of the driver's frontal air bag, excessive internal pressure may cause the inflator to rupture.

Risk: In the event of a crash necessitating deployment of the driver's frontal air bag, the inflator could rupture with metal fragments striking the driver or other occupants resulting in serious injury or death.

Remedy: MBUSA will their notify owners, and Fiat Chrysler will notify the affected Chrysler owners. Dealers for the respective brands will replace the driver's frontal air bag module, free of charge. This recall began November 2016. Mercedes-Benz owners may contact MBUSA customer service at 1-800-367-6372 and Chrysler owners may contact Fiat Chrysler customer service at 1-800-853-1403.

The authority's notice

A12/1733/17Safety recallInjuriesno date · EU Safety Gate

The steering column is not sufficiently earthed. As a result, in the event of an electrostatic discharge, the driver's airbag may be triggered when not required. This could cause an accident.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

The authority's notice

SR/03711/24Safety recallInjuriesno date · EU Safety Gate

The three aluminium screws of the steering box may corrode due to exposure to spray water and aggressive road-grit (salt) used for melting ice. Advanced corrosion could weaken the screws, leading to potential breakage during manoeuvring or parking. If all fixing screws fail, the power-assisted steering could detach, resulting in a loss of power steering and an increased risk of an accident. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

The authority's notice

Engine and transmission

M271DE18AL

135–150 kW (184–204 HP) · petrol

MB7229 · 7G-Tronic / 7G-Tronic Plus, longitudinal (Mercedes 722.9 / NAG2)

automatic · 7 speed

Torque limit700 Nm
MakerMercedes-Benz

We built the code from the model and the gear count. The factory sheet does not state it.

Variant data

What is in this version

Factory data

Trim
E 200 BlueEFFICIENCY Avantgarde
Body
saloon
Fuel
petrol
Transmission
automatic
Engine size
1796 cc
Power
135 kW (184 HP)
Drive
RWD
Production
2009–2013

Factory service interval

The manufacturer specifies this for this version. Of the mileage and the time, the one that comes first is the one that counts.

  • Air filter

    • 60,000 km or 4 years

  • Cabin (pollen) filter

    • 30,000 km or 2 years

  • Brake fluid change

    • first: 3 years, then 2 years(first change at 3 years, then every two years)

  • Spark plugs, petrol

    • 60,000 km or 6 years
All W212 versions

Information, not an expert opinion

We write the descriptions, and we put the source next to them. A person reviews them before they go out. They are still information, not a technical expert opinion.

  • A fault on the list does not mean the car you are looking at has it.
  • A fault missing from the list does not mean the model is fault-free. Write-ups are made model by model. Not all of them are done.
  • You decide whether to buy. This is no substitute for an inspection. That needs a workshop and a history check.
Details in the terms