vinkodex.

Mercedes-Benz E-Class E 200 CGI BlueEFFICIENCY Elegance common faults.

2009–2013, saloon, petrol, 184 HP.

The fault list covers: M271DE18AL engine, MB7229 transmission.

What you save stays on this device only. My saves

4 fault write-ups. All are important. 36 recalls.

If you know the year, pick it. Faults for other years drop out of the list.

Before you buy

Known faults

4 important faults

critical2

The solenoid of the camshaft adjuster is sealed from the factory by nothing more than a plain sealing ring, and over time that starts to leak. The maker's own bulletin names two places: if the leak is between the solenoid and the cylinder head, the sealing ring has to be replaced, and if it comes through the electrical connector, then the solenoid itself.

Show the rest

The more serious trouble is at the connector. Through it the engine oil gets into the engine wiring harness and travels under the insulation by capillary action, so it reaches the engine control unit and other important parts as well. The loss of the control unit is the end of that road, and serious engine damage can follow; alongside the contaminated harness the most varied fault messages can appear. Cases have been reported where the oil ran out of the connector, and the consequential damage after that was already large.

The check is simple: the connector of the solenoid has to be taken off and looked at to see whether it is oily. In the fault memory a faulty solenoid gives one of the codes 0059, 0060, 0063, 0064, 0271, 0272, 0275 and 0276. One thing is worth knowing: according to the maker only the solenoid that has a corresponding code has to be replaced, so if a workshop has changed all four of them alongside two codes, that is worth asking about.

The engine number decides what is in the car. Above engine number 2729..30 759427 (M272) and 2739..30 193592 (M273) the maker already fitted the improved solenoid, under part number A272 051 01 77. The oil-leaking solenoid is a problem on engine numbers below 2729..30 895140 and 2739..30 236360.

The prevention is the oil stop cable, which has to be fitted between the solenoid and the harness: the two wires contain a sealed copper sleeve covered with heat-shrink tubing, and that stops the oil from travelling further. It is available from the factory and is not expensive: the two solenoids were around 33 euros and the two oil stop cables around 31 euros, while replacing the control unit is a four-figure sum.

between 90,000 and 130,000 kmfrom 31 EUR

What to check

  • Ask whether an oil stop cable has been fitted between the camshaft solenoids and the harness
  • Ask for a check: taking the connector off the solenoid shows whether it is oily
  • Read the fault memory and look for codes 0059, 0060, 0063, 0064, 0271, 0272, 0275 and 0276
3 more steps in the write-up

On the four cylinder, supercharged 1.8 M271 the timing chain stretches and the sprockets of the camshaft adjuster (Nockenwellenversteller) wear out. The two go together: a stretched chain makes the adjuster work worse, and a worn adjuster loads the chain further.

Show the rest

The symptom shows up on a cold start first: a short, metallic rattle or knock from the front of the engine that quietens after a few seconds. Later an engine warning light and timing control fault codes join it.

In the official complaint database the four cylinder M271 model group (C 180/200/230/250, E 200, SLK 200/250, GLK 250, CLS 250) has 16 reports between 2008 and 2015, and 8 of those carry a mileage. The raw numbers fall between 61,000 and 152,000 km, from eight reports.

All 16 reports fall on the 2012 to 2014 model years of the C 250. The complaint texts repeatedly mention the maker's extended warranty.

On a warm engine the rattle cannot be heard.

reported complaints only

What to check

  • Start it cold: the chain rattle is audible in the first few seconds and disappears once warm
  • Do not accept the seller bringing the car warmed up; ask them to start it from standing, cold
  • Ask for a fault code read: timing control and camshaft position codes
3 more steps in the write-up

expensive2

In the Mercedes 7 speed 722.9 automatic (7G-Tronic / 7G-Tronic Plus) the mechatronics unit and the conductor plate (Leiterplatte) age over time: jerking on shifts, delayed engagement, a "Getriebe schützen" message, and fault codes on the gearbox electronics.

Show the rest

The repair is typically replacing the mechatronics unit or the conductor plate together with an oil change: not the whole gearbox. The complaint is most common on the longitudinal platforms from around 2005 to 2015 (C/E/ML and the early GLC).

The 9G-Tronic (725.0) is a different design; this applies only to the 7G.

between 100,000 and 220,000 km

What to check

  • Try it cold and warm: a delayed 1 to 2 or 2 to 3 shift is suspect
  • Watch for the gearbox warning or the "Getriebe schützen" message on the dash
  • Ask for a fault code read on the gearbox controller (not just the engine codes)
1 more steps in the write-up

The Mercedes Airmatic system holds the ride height with air springs and electronically controlled dampers. The most common faults over time are the relay, the compressor and a leaking air spring or air line.

Show the rest

The rear air springs of the 2003 to 2009 E-Class (W211) are particularly prone to leaking along the clamps. If the system leaks, the compressor runs continuously, overheats and fails, so an unrepaired leak takes the compressor with it.

Symptoms: one corner of the car sinks by morning, an "Air Suspension" or level control fault message, and compressor noise while standing. It was an option (or standard) across several generations from the W220 S-Class onwards; the estate E-Class often has air springs with level control on the rear axle as standard.

between 100,000 and 220,000 km

What to check

  • In the morning, before setting off, look at all four corners: an uneven stance means a suspected leak
  • With the car standing, listen to the compressor: continuous running indicates it is overworked
  • Ask for a fault code read on the suspension controller (level and pressure sensor codes of the C1132 / C1144 kind)
3 more steps in the write-up

Checklist

Mercedes-Benz E-Class E 200 CGI BlueEFFICIENCY Elegance

First what you would check on any car. Then the faults of this model.

Before you buy

Checklist

The printed sheet starts with what you would check on any car. What you tick stays on this device only.

On every car

Ask the owner

vinkodex.com · Before you buy it, see what can go wrong.

Official recall36 recallsShow

The manufacturer fixes these for free at a franchised dealer. Ask with the VIN whether it was done.

Most recent: 19 November 2024

24V874000VISIBILITY:SUN/MOON ROOF ASSEMBLYVISIBILITY:SUN/MOON ROOF ASSEMBLY19 November 2024 · NHTSA (USA)

Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2001-2011 C-Class, CLK, E-Class, and CLS vehicles. Please see the recall report for a complete list of models and model years. The glass sunroof panel may not be properly secured and can detach.

Risk: A detached sunroof panel can become a road hazard, increasing the risk of a crash.

Remedy: Dealers will inspect and replace the sunroof panel as necessary, free of charge. Owner notification letters were mailed January 10, 2025. Owners may contact MBUSA customer service at 1-800-367-6372. This recall is an expansion of previous NHTSA recall number 22V-954. MBUSA's number for this recall is 2024120001/2/3.

We could not check this: model year. The authority's notice

22V954000VISIBILITY:SUN/MOON ROOF ASSEMBLYVISIBILITY:SUN/MOON ROOF ASSEMBLY23 December 2022 · NHTSA (USA)

Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2001-2011 C-Class, CLK, E-Class, and CLS vehicles. Please refer to MBUSA's recall report for specific vehicle model details. The glass sunroof panel may not be properly secured and may detach.

Risk: A detached sunroof panel may become a road hazard, increasing the risk of a crash.

Remedy: Dealers will inspect and replace the sunroof panel as necessary free of charge. Owner notification letters were mailed February 3, 2023. Owners may contact MBUSA customer service at 1-800-367-6372. This recall expands NHTSA recall number 19V-918. MBUSA's numbers for this recall are 2023010004, 2023010005, and 2023010006.

We could not check this: model year. The authority's notice

22V168000EXTERIOR LIGHTING:LIGHTING CONTROL MODULE:SOFTWAREEXTERIOR LIGHTING:LIGHTING CONTROL MODULE:SOFTWARE18 March 2022 · NHTSA (USA)

Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2010 E350, 2014 G550, 2008-2009 C300, 2008 C350, 2009 CLK550, 2007 SL550, SLK280, and 2008 SLK350 vehicles. Various control units may have been updated with incorrect software configuration during a service repair. This can result in various system failures, such as loss of drive power, reduced exterior lighting, or loss of dynamic control functions, including stability and traction control.

Risk: Various system failures, such as loss of drive power, reduced exterior lighting, or loss of dynamic control functions including stability and traction control, can increase the risk of a crash.

Remedy: Dealers will update the software configuration on the affected control units, free of charge. Owner notification letters were mailed May 3, 2022. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2022040003.

We could not check this: model year. The authority's notice

21V638000AIR BAGS:FRONTALAIR BAGS:FRONTAL13 August 2021 · NHTSA (USA)

Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2015-2016 E400 Coupe, 2012-2015 C250 Coupe, C350 Coupe, C63 AMG Coupe, 2011-2014 E350 Coupe, and 2012-2014 E350 Cabrio vehicles. An incorrect front passenger air bag may have been installed during a prior repair.

Risk: An incorrect air bag may not function properly in a crash, increasing the risk of injury.

Remedy: Dealers will replace the front passenger air bag on the affected vehicles, free of charge. Owner notification letters were mailed on September 10, 2021. Owners may contact MBUSA customer service at 1-800-367-6372.

We could not check this: model year. The authority's notice

19V918000VISIBILITY:SUN/MOON ROOF ASSEMBLYVISIBILITY:SUN/MOON ROOF ASSEMBLY20 December 2019 · NHTSA (USA)

Mercedes-Benz USA, LLC. (MBUSA) is recalling certain 2001-2011 vehicles. The bonding between the glass panel and the sliding roof frame may deteriorate, possibly resulting in the glass panel detaching from the vehicle. For a full list of the affected models visit: https://static.nhtsa.gov/odi/rcl/2019/RMISC-19V918-4126.pdf

Risk: A detached glass panel can separate from the vehicle and become a road hazard, increasing the risk of a crash.

Remedy: MBUSA will notify owners, and dealers will inspect the glass panel bonding and replace the sliding roof, as necessary, free of charge. The recall began July 10, 2020. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2020040011.

We could not check this: model year. The authority's notice

18V043000AIR BAGS:FRONTAL:PASSENGER SIDE:INFLATOR MODULEAIR BAGS:FRONTAL:PASSENGER SIDE:INFLATOR MODULE10 January 2018 · NHTSA (USA)

Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2013 C250, C250 Coupe, C350 Coupe 4Matic, C300 4Matic, C350, C350 Coupe, C63 AMG, C63 Coupe, E350 Cabrio, E350 Coupe, E550 Cabrio, E350 Coupe 4Matic, E550 Coupe, GLK350 4Matic, GLK250 Bluetec 4Matic, GLK350, SLS Coupe, SLS AMG GT Coupe, and SLS Roadster vehicles sold, or ever registered, in the states of Alabama, California, Florida, Georgia, Hawaii, Louisiana, Mississippi, South Carolina, Texas, Puerto Rico, American Samoa, Guam, the Northern Mariana Islands (Saipan), and the U.S. Virgin Islands or "Zone A." Additionally, MBUSA is recalling certain 2010 C300, C300 4Matic, C63 AMG, E350 Coupe, E550 Coupe, GLK350, and GLK350 4Matic vehicles ever registered in the states of Arizona, Arkansas, Delaware, District of Columbia, Illinois, Indiana, Kansas, Kentucky, Maryland, Missouri, Nebraska, Nevada, New Jersey, New Mexico, North Carolina, Ohio, Oklahoma, Pennsylvania, Tennessee, Virginia, and West Virginia or "Zone B." MBUSA is also recalling certain 2009 C300, C300 4Matic, C63 AMG, and C350 vehicles ever registered in the states of AK, CO, CT, ID, IA, ME, MA, MI, MN, MO, NH, NY, ND, OR, RI, SD, UT, VT, WA, WI and WY or "Zone C." In the event of a crash necessitating deployment of the passenger frontal air bag, these passenger air bag inflator may explode due to propellant degradation occurring after long-term exposure to absolute humidity and temperature cycling.

Risk: An inflator explosion may result in sharp metal fragments striking the driver or other occupants resulting in serious injury or death.

Remedy: MBUSA will notify owners, and dealers will replace the passenger frontal air bag module, free of charge. Mercedes issued an interim notification to owners on February 23, 2018. A second notice will be mailed when remedy parts are available. Owners may contact MBUSA customer service at 1-877-496-3691.

We could not check this: model year. The authority's notice

A12/1352/17Safety recallFire1 September 2017 · EU Safety Gate

The starter current limiter may be overloaded and overheat. As a consequence, the surrounding components could ignite, leading to a fire.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: 01/09/2017

We could not check this: model year. The authority's notice

17V017000AIR BAGS:FRONTAL:PASSENGER SIDE:INFLATOR MODULEAIR BAGS:FRONTAL:PASSENGER SIDE:INFLATOR MODULE10 January 2017 · NHTSA (USA)

Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2012 C300 4Matic, C250, C250 Coupe, C350, C350 Coupe 4Matic, C350 Coupe, C63 AMG, C63 AMG Coupe, E350 Coupe 4Matic, E350 Cabrio, E350 Coupe, E550 Cabrio, E550 Coupe, GLK350 4Matic, GLK350, SLS AMG Cabrio, and SLS AMG Coupe vehicles originally sold, or ever registered, in Alabama, California, Florida, Georgia, Hawaii, Louisiana, Mississippi, South Carolina, Texas, Puerto Rico, American Samoa, Guam, the Northern Mariana Islands (Saipan), and the U.S. Virgin Islands, or "Zone A." Additionally, unless included in "Zone A" above MBUSA is recalling certain 2009 C300 4Matic, C300, C350 and C63 AMG vehicles originally sold, or ever registered, in Arizona, Arkansas, Delaware, District of Columbia, Illinois, Indiana, Kansas, Kentucky, Maryland, Missouri, Nebraska, Nevada, New Jersey, New Mexico, North Carolina, Ohio, Oklahoma, Pennsylvania, Tennessee, Virginia, and West Virginia, or "Zone B." Additionally, unless included in "Zone A" or "Zone B" above MBUSA is recalling certain 2008 C300 4Matic, C300, and C350 vehicles originally sold, or ever registered, in Alaska, Colorado, Connecticut, Idaho, Iowa, Maine, Massachusetts, Michigan, Minnesota, Montana, New Hampshire, New York, North Dakota, Oregon, Rhode Island, South Dakota, Utah, Vermont, Washington, Wisconsin, and Wyoming. These vehicles are equipped with certain air bag inflators assembled as part of the passenger frontal air bag modules, and used as original equipment or replacement equipment. In the event of a crash necessitating deployment of the front air bags, these inflators may rupture due to propellant degradation occurring after long-term exposure to absolute humidity and temperature cycling.

Risk: An inflator rupture may result in metal fragments striking the vehicle occupants resulting in serious injury or death.

Remedy: MBUSA will notify owners, and dealers will replace the front passenger air bag modules, free of charge. Owners were sent an interim notification in March 2017. Second notices started going out in October 2018 and continue to be mailed as parts become available. Owners may contact MBUSA customer service at 1-877-496-3691

We could not check this: model year. The authority's notice

16V363000AIR BAGS:FRONTAL:PASSENGER SIDE:INFLATOR MODULEAIR BAGS:FRONTAL:PASSENGER SIDE:INFLATOR MODULE26 May 2016 · NHTSA (USA)

Mercedes-Benz USA, LLC (MBUSA) is recalling certain model year 2008-2011 C300 Sedan, C300 4matic Sedan, C350 Sedan, C63 AMG Sedan vehicles, 2010-2011 GLK350, GLK350 4-Matic and E350 Coupe vehicles, 2011 SLS AMG, E350 Convertible, E550 Coupe and E550 Convertible vehicles originally sold, or ever registered, in Alabama, California, Florida, Georgia, Hawaii, Louisiana, Mississippi, South Carolina, Texas, Puerto Rico, American Samoa, Guam, the Northern Mariana Islands (Saipan), and the U.S. Virgin Islands, or "Zone A." Additionally, unless included in "Zone A" above, MBUSA is recalling certain model year 2008 C300 Sedan, C350 Sedan, C63 AMG Sedan and C300 4-Matic Sedan vehicles originally sold, or ever registered, in Arizona, Arkansas, Delaware, District of Columbia, Illinois, Indiana, Kansas, Kentucky, Maryland, Missouri, Nebraska, Nevada, New Jersey, New Mexico, North Carolina, Ohio, Oklahoma, Pennsylvania, Tennessee, Virginia, and West Virginia, or "Zone B." Vehicles not originally sold or ever registered in either Zones A or B are not subject to this safety recall. These vehicles are equipped with certain air bag inflators assembled as part of the passenger frontal air bag modules, and used as original equipment or replacement equipment. In the event of a crash necessitating deployment of the front air bags, these inflators may rupture due to propellant degradation occurring after long-term exposure to absolute humidity and temperature cycling.

Risk: An inflator rupture may result in metal fragments striking the vehicle occupants resulting in serious injury or death.

Remedy: MBUSA will notify owners, and dealers will replace the passenger frontal air bag modules, free of charge. Owners were sent an interim notification October 2016. A second notice will be mailed when remedy parts are available. Owners may contact MBUSA customer service at 1-877-496-3691.

We could not check this: model year. The authority's notice

16V081000AIR BAGS:FRONTAL:DRIVER SIDE:INFLATOR MODULEAIR BAGS:FRONTAL:DRIVER SIDE:INFLATOR MODULE11 February 2016 · NHTSA (USA)

Mercedes-Benz USA, LLC. (MBUSA) is recalling certain model year 2009-2010 ML320 BlueTec 4Matic, GL320 BlueTec 4Matic and R320 CDI 4Matic, 2011 E350 Cabriolet and E550 Cabriolet, 2009-2011 ML350, ML350 4Matic, ML550 4Matic, ML63 AMG, and C63 AMG, 2010-2011 ML450 4Matic Hybrid, E350 Coupe, E350 4Matic, E550 Coupe, E550 4Matic, and E63 AMG, 2011-2012 GL350 BlueTec 4Matic and R350 BlueTec 4Matic, 2009-2012 GL450 4Matic, GL550 4Matic and R350 4Matic, 2007-2008 SLK280, SLK350, and SLK55 AMG, 2011-2014 SLS AMG Coupe, 2012 SLS AMG Cabriolet, 2013-2014 SLS AMG GT and SLS AMG GT Cabriolet, 2005 C230 Kompressor and C320, 2006-2007 C230, 2006-2011 C350, 2008-2011 C300 and C300 4Matic, 2010-2012 GLK350 and GLK350 4Matic and 2007-2008 Chrysler Crossfire vehicles. Upon deployment of the driver's frontal air bag, excessive internal pressure may cause the inflator to rupture.

Risk: In the event of a crash necessitating deployment of the driver's frontal air bag, the inflator could rupture with metal fragments striking the driver or other occupants resulting in serious injury or death.

Remedy: MBUSA will their notify owners, and Fiat Chrysler will notify the affected Chrysler owners. Dealers for the respective brands will replace the driver's frontal air bag module, free of charge. This recall began November 2016. Mercedes-Benz owners may contact MBUSA customer service at 1-800-367-6372 and Chrysler owners may contact Fiat Chrysler customer service at 1-800-853-1403.

We could not check this: model year. The authority's notice

15V792000FUEL SYSTEM, GASOLINE:DELIVERYFUEL SYSTEM, GASOLINE:DELIVERY24 November 2015 · NHTSA (USA)

Mercedes-Benz USA, LLC. (MBUSA) is recalling certain model year 2014 E350 and E350 4Matic sedans manufactured June 4, 2014, to July 9, 2014. The affected vehicles were built with a fuel feed line that has a single flare fitting instead of a double flare fitting.

Risk: If the fuel feed line has the incorrect flare fitting, the connection between the fuel hose and the fuel feed line might develop a leak or may completely disconnect. Leaking fuel in the presence of an ignition source increases the risk of a fire and if the fuel feed line disconnects, the vehicle would stall, increasing the risk of a crash.

Remedy: MBUSA will notify owners, and dealers will install the correct fuel line, free of charge. This recall began on January 11, 2016. Owners may contact Mercedes-Benz customer service at 1-800-367-6372.

We could not check this: model year. The authority's notice

15V505000ENGINE AND ENGINE COOLING:ENGINEENGINE AND ENGINE COOLING:ENGINE11 August 2015 · NHTSA (USA)

Mercedes-Benz USA, LLC (MBUSA) is recalling certain model year 2016 Mercedes Benz E350, E400, E400 4Matic, E63 4M S AMG, E350 4Matic, E63-4M S AMG, 2015 CLS400, CLS400 4Matic, CLS550, CLS63-4M "P" AMG, and CLS550 4Matic vehicles manufactured April 16, 2015, to April 22, 2015. The integral steel cable that secures the rubber seal to the bulkhead might have been damaged due to the supplier rework of the rubber seal. In the event the rubber seal is not properly secured around the engine compartment, it is possible for the rubber seal to temporarily stick to the hood when it is opened and then may fall into the engine bay when the hood is closed.

Risk: If the rubber seal falls into the engine compartment, it may contact parts of the engine or exhaust system, increasing the risk of a fire.

Remedy: MBUSA will notify owners, and dealers will replace the rubber seal, in the engine compartment, free of charge. The recall began on September 2, 2015. MBUSA's number is 2015080001. Owners may contact MBUSA customer service at 1-201-573-5339.

We could not check this: model year. The authority's notice

15V088000STRUCTURE:BODY:HOODSTRUCTURE:BODY:HOOD13 February 2015 · NHTSA (USA)

Mercedes-Benz USA, LLC. (MBUSA) is recalling certain model year 2013-2015 E350 Sedan, E350 4Matic Sedan, E350 4Matic Station Wagon, E400 Hybrid Sedan, CLS 550 CGI, and CLS550 4Matic, 2013-2014 E550 4Matic Sedan, 2013 E63 Sedan, E63 Station Wagon and CLS63, 2014-2015 CLS63 4Matic, E63 4Matic Sedan, E63 4Matic Sedan "S", and E63 4Matic Station Wagon, 2015 CLS400, 2015 E400 Sedan, E400 4Matic Sedan and CLS400 4Matic and 2014 CLS63 "S". The affected vehicles have a rubber seal at the back of the engine bay that may temporarily stick to the hood when it is opened and then may fall into the engine bay when the hood is closed.

Risk: If the rubber seal falls into the engine compartment, it may contact parts of the exhaust system, increasing the risk of a fire.

Remedy: MBUSA will notify owners, and dealers will attach four additional retaining clips to the rubber seal, free of charge. The recall began March 6, 2015. Owners may contact MBUSA customer service at 1-201-573-5339. MBUSA's number for this recall is 2015020001.

We could not check this: model year. The authority's notice

14V818000SEAT BELTS: REAR/OTHER:BUCKLE ASSEMBLYSEAT BELTS: REAR/OTHER:BUCKLE ASSEMBLY24 December 2014 · NHTSA (USA)

Mercedes-Benz USA, LLC. (MBUSA) is recalling certain model year 2015 E250 Diesel, E250 Blue Tec 4 Matic, E350 Sedan, E350 Sedan 4 Matic, E350 Wagon 4 Matic, E400 Sedan, E400 Sedan 4 Matic, E63 Sedan, and E63 Wagon vehicles manufactured October 8, 2014, to October 24, 2014. In the affected vehicles, the double seat belt buckle for the middle position of the rear passenger seat could fail under loading experienced in a severe frontal crash.

Risk: If the middle position double seat belt buckle assembly fails under load such as in a severe frontal crash, there is an increased risk of injury to the seat occupant.

Remedy: MBUSA will notify owners, and dealers will replace the double seat belt buckle, free of charge. The recall began February 2, 2015. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2014120006.

We could not check this: model year. The authority's notice

12V492000AIR BAGS:SIDE/WINDOWAIR BAGS:SIDE/WINDOW9 October 2012 · NHTSA (USA)

Mercedes-Benz is recalling certain model year 2012 E350 and E550 Coupe vehicles, manufactured April 2, 2012, through June 29, 2012. Improper stitching of the right side window curtain air bag may cause it to not deploy as intended in the affected vehicles.

Risk: In the event of an accident necessitating the deployment of the right window curtain air bag, the improper stitching may cause it to deflate more quickly than intended, reducing the protection it may provide, resulting in an increased risk of injury to vehicle occupants.

Remedy: Mercedes-Benz will notify owners, and dealers will replace the right side window curtain air bag. The recall began on December 21, 2012. Owners may contact Mercedes-Benz at 1-800-367-6372.

We could not check this: model year. The authority's notice

12V264000SUSPENSION:REARSUSPENSION:REAR12 June 2012 · NHTSA (USA)

MERCEDES-BENZ IS RECALLING CERTAIN MODEL YEAR 2007-2009 E350 4MATIC WAGON VEHICLES MANUFACTURED FROM JULY 1, 2006, THROUGH APRIL 30, 2009. A CONNECTING ROD FOR THE LOAD LEVELING REAR SUSPENSION SYSTEM MAY FAIL.

Risk: IF THIS OCCURS, THE DRIVER MAY HAVE REDUCED VEHICLE CONTROL, INCREASING THE RISK OF A CRASH.

Remedy: MERCEDES-BENZ WILL NOTIFY OWNERS, AND DEALERS WILL REPLACE ALL THE CONNECTING RODS, FREE OF CHARGE. THE SAFETY RECALL BEGAN ON SEPTEMBER 7, 2012. OWNERS MAY CONTACT MERCEDES-BENZ AT 1-800-367-6372.

We could not check this: model year. The authority's notice

A12/00017/22Safety recallFireno date · EU Safety Gate

A trapped particle may damage the sealing between the fuel rail and fuel injector, which could cause fuel to leak into the engine compartment. Consequently, leaking fuel may come into contact with hot parts of the engine, increasing the risk of fire. The product does not comply with the requirements laid down in the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

We could not check this: model year. The authority's notice

A12/00280/20Safety recallInjuriesno date · EU Safety Gate

The adhesive bond between the glass panel and the sliding-roof frame may not meet the specifications. As a result, the glass panel could become completely detached from the vehicle, posing the risk to the following traffic.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

We could not check this: model year. The authority's notice

A12/00391/23Safety recallInjuriesno date · EU Safety Gate

Due to improper adhesive bonding of the glass panel to the sliding roof frame, the panel may detach from the moving vehicle, creating a risk of an accident, injuries. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

We could not check this: model year. The authority's notice

A12/00618/20Safety recallFireno date · EU Safety Gate

Moisture can penetrate into the busbar, giving rise to conductive contacts between the individual lines inside it. The resulting current flows could overheat the plastic material of the busbar, increasing the risk of fire.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

We could not check this: model year. The authority's notice

A12/0082/17Safety recallInjuriesno date · EU Safety Gate

The power-assisted steering control units may have been fitted with defectively welded contacts. As a result, a permanent electrical connection between the contacts cannot be guaranteed, which could lead to loss of support to the power-assisted steering and thus an increased risk of accidents.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

We could not check this: model year. The authority's notice

A12/01236/20Safety recallInjuriesno date · EU Safety Gate

The driver and passenger airbags of the company Takata in vehicles with ammonium nitrate gas generators without drying agents could, under certain climate conditions, lead over time to a chemical change in the fuel. In the event of an accident triggering the release of the driver or passenger airbag, this change could cause the gas generators to burst. If a gas generator ruptures, the airbag would then have no restraining function and loose parts from the gas generator could reach the vehicle interior. This would increase the risk of injury for passengers.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

We could not check this: model year. The authority's notice

A12/01237/22Safety recallFireno date · EU Safety Gate

The seal for the special plug-in contact of the gearbox designed to protect against contact with moisture and splashing water is improperly installed. Thus splashed water can enter the socket contact when driving in wet conditions and can lead to a short circuit, increasing the risk of a fire. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

We could not check this: model year. The authority's notice

A12/01448/22Safety recallEnvironment, Injuriesno date · EU Safety Gate

Faulty configurations of the control units (traction systems, signal recording triggering modules, engine control units and headlights) could cause one or more control units to malfunction, which could increase the risk of an accident. The exhaust emissions exceed the legal limits, posing a risk to the environment. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

We could not check this: model year. The authority's notice

A12/0164/19Safety recallInjuriesno date · EU Safety Gate

There may be cracks in a securing nut in the steering gear of rear-wheel-drive vehicles. The nut could consequently break if the steering system is subject to a very high lateral force, which could result in rotating parts in the steering gear affecting the casing and thereby blocking the steering system.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

We could not check this: model year. The authority's notice

A12/0296/19Safety recallInjuriesno date · EU Safety Gate

In vehicles with rear-wheel drive, a lock nut in the steering gear may be cracked. Consequently, when the steering is placed under high forces it could break, which would block the steering gear and increase the risk of accident.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

We could not check this: model year. The authority's notice

A12/0334/17Safety recallInjuriesno date · EU Safety Gate

The front passenger occupant detection control unit may have been incorrectly installed and could misclassify a passenger as a child seat. That would cause the front passenger airbag to be deactivated in the event of an accident and would thereby increase the risk of injury for the passenger.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

We could not check this: model year. The authority's notice

A12/0457/17Safety recallInjuriesno date · EU Safety Gate

Following the update of the control unit coding, the coding parameters of the control unit could be defective. This could give rise to various unplanned reactions in the vehicle: the wrong airbag could be triggered in the event of an accident, the airbag control unit may not recognise the belt buckle status, the engine control unit could be coded with a false maximum speed or various assistance systems may not function.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

We could not check this: model year. The authority's notice

A12/0626/17Safety recallInjuriesno date · EU Safety Gate

The propellant mixing ratio in certain seat-belt pre-tensioner igniters may be incorrect. As a result, in the event of an accident where the front seat-belt pre-tensioners are activated, the pre-tensioners would not provide the restraint performance required if the igniter did not ignite as intended. This could put the occupants at a greater risk of injury.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

We could not check this: model year. The authority's notice

A12/0763/17Safety recallInjuriesno date · EU Safety Gate

The mixture ratio of the fuel in the inflators of the front-passenger knee, pelvic and side curtain airbags may not be correct. In the event of an accident requiring the deployment of the airbags, this could lead to the airbags not inflating properly.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

We could not check this: model year. The authority's notice

A12/0837/17Safety recallInjuriesno date · EU Safety Gate

The bonding between the top and the lower part of the roof-mounted taxi sign may not be adequate. As a consequence, the top of the taxi sign may become detached from the lower part with a risk of accidents for other road users.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

We could not check this: model year. The authority's notice

A12/1259/17Safety recallInjuriesno date · EU Safety Gate

The mixing ratio of the propellant for the seat-belt pre-tensioner igniters may be incorrect. In an accident in which the rear seat-belt pre-tensioners were activated, the igniters might not ignite as intended and the pre-tensioners would not provide the restraint performance required.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

We could not check this: model year. The authority's notice

A12/1608/18Safety recallInjuriesno date · EU Safety Gate

The operation of the active bonnet may be faulty because of a wrong positioning of the sensor hose in the front bumper. In the event of a collision with a pedestrian, the pedestrian would not be detected and the active bonnet would not be triggered. This could increase the potential risk of injury for the pedestrian.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

We could not check this: model year. The authority's notice

A12/1733/17Safety recallInjuriesno date · EU Safety Gate

The steering column is not sufficiently earthed. As a result, in the event of an electrostatic discharge, the driver's airbag may be triggered when not required. This could cause an accident.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

We could not check this: model year. The authority's notice

A12/1753/19Safety recallInjuriesno date · EU Safety Gate

The rear spoiler might not have been attached in accordance with requirements. As a result, the rear spoiler could become completely detached from the vehicle at high speeds, posing a risk to the following traffic.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

We could not check this: model year. The authority's notice

SR/03711/24Safety recallInjuriesno date · EU Safety Gate

The three aluminium screws of the steering box may corrode due to exposure to spray water and aggressive road-grit (salt) used for melting ice. Advanced corrosion could weaken the screws, leading to potential breakage during manoeuvring or parking. If all fixing screws fail, the power-assisted steering could detach, resulting in a loss of power steering and an increased risk of an accident. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

We could not check this: model year. The authority's notice

Engine and transmission

M271DE18AL

135–150 kW (184–204 HP) · petrol

MB7229 · 7G-Tronic / 7G-Tronic Plus, longitudinal (Mercedes 722.9 / NAG2)

automatic · 7 speed

Torque limit700 Nm
MakerMercedes-Benz

We built the code from the model and the gear count. The factory sheet does not state it.

Variant data

What is in this version

Factory data

Trim
E 200 CGI BlueEFFICIENCY Elegance
Body
saloon
Fuel
petrol
Transmission
automatic
Engine size
1796 cc
Power
135 kW (184 HP)
Drive
RWD
Production
2009–2013

Factory service interval

The manufacturer specifies this for this version. Of the mileage and the time, the one that comes first is the one that counts.

  • Air filter

    • 60,000 km or 4 years
  • Cabin (pollen) filter

    • 30,000 km or 2 years
  • Brake fluid change

    • first: 3 years, then 2 years(first change at 3 years, then every two years)
  • Spark plugs, petrol

    • 60,000 km or 6 years

Information, not an expert opinion

We write the descriptions, and we put the source next to them. A person reviews them before they go out. They are still information, not a technical expert opinion.

  • A fault on the list does not mean the car you are looking at has it.
  • A fault missing from the list does not mean the model is fault-free. Write-ups are made model by model. Not all of them are done.
  • You decide whether to buy. This is no substitute for an inspection. That needs a workshop and a history check.
Details in the terms