vinkodex.

Volkswagen Golf 2.0 TDI 150hp Style common faults.

2020–2024, hatchback, diesel, 150 HP.

The fault list covers: DSRB, DTSB engine, DQ381 transmission.

What you save stays on this device only. My saves

6 fault write-ups. 4 important. 10 recalls.

If you know the year, pick it. Faults for other years drop out of the list.

Before you buy

Known faults

4 important faults

critical1

On short urban trips the particulate filter cannot burn through. The engine control unit then injects extra fuel late in the cycle to heat the filter, and part of that fuel passes down the cylinder wall into the sump. The oil level rises, the oil thins out, and it lubricates worse.

Show the rest

The maker addresses this itself. Audi's 2015 service bulletin (01-15-18) tells the technician how to read the oil level on 2.0 TDI engines, because an overfilled level triggers an oil change message with no engine warning light and no stored fault code.

An oil level above the maximum calls for an immediate oil change, and it points to short urban trips. A diesel driven only in town is a bigger risk from both the particulate filter and the turbo.

A thinned, rising oil level is one precondition of a runaway engine. A diesel controls torque with the quantity of fuel injected, and it has no throttle. So if enough combustible liquid reaches the intake, the engine starts running on its own oil, and cutting the injection or switching off the ignition will not stop it. The revs climb on their own until the engine destroys itself.

A raised oil level alone is rarely enough for this. The classic trigger is a failed turbo shaft seal that feeds oil mist into the intake. But the two go together: thinned oil lubricates worse, and poorer lubrication damages the turbo bearing first.

If it happens while driving, the key does not help. Only cutting off the air does: cover the intake, discharge a dry powder extinguisher into the intake tract, or on a manual select a high gear with the parking brake on and release the clutch quickly.

What to check

  • Pull the dipstick with a cold engine on level ground: the level must not be above the maximum mark
  • Smell the oil on the dipstick: a diesel smell means it is thinned with fuel
  • Ask whether the dash has ever shown an oil level sensor or oil change message
5 more steps in the write-up

expensive3

On AdBlue (SCR) diesels the NOx sensor after the catalyst ages, and the tip of the dosing valve crystallises. An AdBlue warning appears on the dash, often with a countdown ("X km of starts remaining"), while the tank is full. Crystallisation typically forms with short trip, urban use, or from poor quality AdBlue; on a car standing below freezing the circuit can freeze up too.

Show the rest

At the end of the countdown there is a start inhibit: the car can become undriveable until it is repaired. The fault is not always the SCR catalyst: the cause is the sensor or the dosing valve.

between 100,000 and 160,000 km

What to check

  • Check whether there is an AdBlue filler (next to the fuel cap or in the boot): if there is not, this car does not have the system
  • Read all the dash messages after switching the ignition on: there should be no AdBlue warning and no km countdown
  • Ask for a fault code read: the codes P20EE, P2202 and P229F belong here. A cleared code comes back after a few tens of kilometres
2 more steps in the write-up

The 7 speed, wet clutch DSG that replaced the DQ250 in the MQB models (0GC / DQ381) is vulnerable from the mechatronics side. Typical faults are a harsh 2 to 3 shift, delayed D/R engagement and limp mode; a fault in the clutch position sensors gives a separate group of codes.

Show the rest

The wet clutch is more durable than the dry one, but as it wears you get shuddering and slipping when pulling away: the revs flare and the acceleration does not follow.

What to check

  • Standing still on the brake, shift between D and R and watch the engagement time and any jolt
  • Try pulling away on a slope too: shuddering, or revving without pulling, points to clutch wear
  • On the test drive watch the 2 to 3 shift specifically, cold and warm
2 more steps in the write-up

The internal springs of the flywheel tire, and the two discs knock against each other. The signs are a rattling or knocking from the bellhousing at idle and when releasing the clutch pedal, and vibration through the floor. If the clutch slips without a burnt smell, that also points to the flywheel. It is worth replacing in time: a disintegrated flywheel can destroy the bellhousing too. At a clutch replacement the two go together anyway.

What to check

  • At idle, without touching the clutch pedal, listen for the rattle from the bellhousing, then press the pedal: if it stops, that is suspect
  • Watch for the characteristic clatter on starting and switching off
  • Put your foot on the floor at idle: a noticeable vibration indicates tired springs
2 more steps in the write-up

comfort1

On early Golf VIII cars the MIB3 infotainment can freeze or restart, the reversing camera image can stay black, and the key recognition and the driver assistance systems can misbehave. In December 2020 the maker started a service action to update the software. It is more common on the 2020 model year, and rarer from 2021. The touch slider under the display is not illuminated in the dark.

What to check

  • Cycle the ignition two or three times, and check whether the screen comes up every time
  • Select reverse and check whether the camera image appears immediately
  • Ask for the service book or the dealer history: was the software update done
3 more steps in the write-up

cheap repair1

The dash shows "Error: Workshop! Only leave vehicle in position P" with an audible warning. The message appears in whatever language the car is set to, for example "Fehler: Werkstatt! Fahrzeug nur in Stellung P verlassen" in German.

Show the rest

The message points at the gearbox, but the fault is not there. A tiny switch sits in the module under the selector lever and signals that the lever is in park (P). Its contact wears and can also burn. That makes the signal unreliable, and the car warns you. The fault codes appear as 617752, P173400 or B116229.

At first it is intermittent. Sometimes the message comes up, sometimes not, so a short test drive easily misses it. Later it becomes permanent, and the gearbox can drop into limp mode.

This fault looks more expensive than it is. The maker released a separate retrofit switch kit for it (5Q0713128A for the black module, 3Q0713128 for the white one), which can be fitted in half an hour. The kit costs 70 to 100 pounds. At a franchised dealer, however, the whole selector lever module sometimes gets replaced, which costs 626 to 1,000 pounds there. So the difference between the two routes is roughly tenfold.

The affected group is post 2013 MQB platform Volkswagen, Audi, Seat and Skoda cars with a DSG gearbox. The switch is in these gearboxes, because that is what these cars have in common. The part itself is not part of the gearbox but of the module under the lever.

What to check

  • Watch the dash after starting: the message is intermittent and can be missed on a short loop
  • Move the lever from P to D and back several times, then get out and lock the car
  • Ask whether the selector lever switch has been replaced already, and ask for the invoice
2 more steps in the write-up

Checklist

Volkswagen Golf 2.0 TDI 150hp Style

First what you would check on any car. Then the faults of this model.

Before you buy

Checklist

The printed sheet starts with what you would check on any car. What you tick stays on this device only.

On every car

Ask the owner

vinkodex.com · Before you buy it, see what can go wrong.

Official recall10 recallsShow

The manufacturer fixes these for free at a franchised dealer. Ask with the VIN whether it was done.

Most recent: 7 October 2026

SR/02935/26Safety recallInjuries7 October 2026 · EU Safety Gate

Moisture ingress could lead to corrosion of a steering rack bolt, which may result in a fracture of the bolt and a loss of steering capability, increasing the risk of accidents. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: 07/10/2026

We could not check this: model year. The authority's notice

A12/00188/24Safety recallFireno date · EU Safety Gate

The thermal protection between the brake force booster and the emissions control device in front of the coupling support with the brake fluid reservoir may not have been correctly fitted. The coupling support could melt, leading to a leak of brake fluid, which could ignite if it comes into contact with hot components. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

We could not check this: model year. The authority's notice

A12/00262/21Safety recallInjuriesno date · EU Safety Gate

Due to a manufacturing error, the brake-pedal plate may not have been adequately welded and could become completely detached when the brake pedal is suddenly applied. As a result, the application of the brakes will be impaired, increasing the risk of an accident.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

We could not check this: model year. The authority's notice

A12/00565/22Safety recallFire, Injuriesno date · EU Safety Gate

The amount of extinguishing sand in the fuse of the high-voltage system is not sufficient in the event of a short circuit to the high-voltage safety system. This may cause it to burst, increasing the risk of injuries. Furthermore, the blown fuse can interrupt electrical flow of current leading to a voltage drop inside the vehicle, increasing the risk of fire. The product does not comply with the Regulation on the approval and market surveillance of Motor Vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

We could not check this: model year. The authority's notice

A12/00584/22Safety recallBurns, Fireno date · EU Safety Gate

The engine covers installed on affected vehicles could detach from their fixings depending on the conditions of use (e.g. very sporty driving, or poor road surfaces) and their age. A loose engine cover could come into contact with the hot area of the exhaust gas turbocharger, increasing the risk of burns or fire. The product does not comply with the Regulation on the approval and market surveillance of Motor Vehicles and their trailers, and of systems, components and separate technical units intended for such vehicle.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

We could not check this: model year. The authority's notice

A12/01007/20Safety recallInjuriesno date · EU Safety Gate

The emergency call service may not be functioning. As a result, the system may not assist the car occupants by contacting the call centre/rescue coordination centre in the event of an accident.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

We could not check this: model year. The authority's notice

A12/01322/21Safety recallInjuriesno date · EU Safety Gate

The luggage net may be incorrectly affixed. As a result, luggage could end up in the passenger compartment, causing injury to the occupants.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

We could not check this: model year. The authority's notice

INFO/00090/21Safety recallInjuriesno date · EU Safety Gate

Faulty crash sensors for the airbag restraint systems may have been installed in the doors. This could impair the protective effect of the side airbags, head airbags and/or belt tensioners, increasing the risk of injury in the event of an accident.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

We could not check this: model year. The authority's notice

SR/02758/25Safety recallInjuriesno date · EU Safety Gate

The safety belt on the front passenger side may not be correctly secured to the lower anchorage point, compromising the restraining effect of the safety-belt. In the event of an accident, this may result injuries to the person sitting in the passenger seat. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

We could not check this: model year. The authority's notice

SR/02762/25Safety recallInjuriesno date · EU Safety Gate

The front-seat belt assemblies may not be correctly secured to the anchorage point near the bottom of the B-pillar. If the lower anchorage point of the belt assembly is not secured, the restraining effect of the safety-belt is severely compromised. In the event of an accident, this may result in injuries to the persons sitting in the driver’s seat and/or the passenger seat. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

We could not check this: model year. The authority's notice

Engine and transmission

2 engines · 1 transmissions

DSRB · 2.0 TDI

110 kW (150 HP) · diesel

DQ381 · 7-speed DSG, wet clutch

DSG · 7 speed

Clutchwet
Torque limit420 Nm
MakerVolkswagen

We built the code from the model and the gear count. The factory sheet does not state it. More than one engine code is possible. The fault list shows the faults of each.

Variant data

What is in this version

Factory data

Trim
Style
Body
hatchback
Fuel
diesel
Transmission
automatic
Engine size
1968 cc
Power
110 kW (150 HP)
Drive
FWD
Production
2020–2024

Factory service interval

The manufacturer specifies this for this version. Of the mileage and the time, the one that comes first is the one that counts.

  • Air filter

    • 60,000 km or 4 years
  • Cabin (pollen) filter

    • 30,000 km or 2 years
  • Engine oil and oil filter

    • LongLife30,000 km or 2 years(valid only with LongLife-approved oil)
    • 15,000 km or 1 year
  • Brake fluid change

    • first: 3 years, then 2 years(first change at 3 years, then every two years)
  • DSG oil change, WET clutch gearbox

    • 60,000 km or 4 years
  • Timing belt, 1.6 / 2.0 TDI (EA188/EA189/EA288)

    • 210,000 km(EA288, including the 1.6 TDI, with no time limit. 130,000 miles = 209,215 km. Parts maker repair specification, read by a human. The interval chart at https://www.rwcmotorsport.com/tech/tdi-maintenance.php gives the same figure independently.)
  • Coolant (antifreeze) change

    • first: 193,000 km or 10 years, then 97,000 km or 5 years(G13 / G12++: first change at 120,000 miles or 10 years, then every 60,000 miles or 5 years)
  • Fuel filter, diesel

    • 60,000 km or 2 years

Information, not an expert opinion

We write the descriptions, and we put the source next to them. A person reviews them before they go out. They are still information, not a technical expert opinion.

  • A fault on the list does not mean the car you are looking at has it.
  • A fault missing from the list does not mean the model is fault-free. Write-ups are made model by model. Not all of them are done.
  • You decide whether to buy. This is no substitute for an inspection. That needs a workshop and a history check.
Details in the terms