The PD (pump injector) unit is held in the cylinder head by a single side bolt. Over time the seat works itself loose: the mounting slackens, the copper ring no longer seals, and hot combustion gas blows past. First you hear a characteristic "puffing", rhythmic blowing noise from the top of the engine when cold, soot appears under the cam cover, and then the seat surface in the cylinder head erodes. At that point replacing the seal is not enough: the head has to be refurbished or replaced. It affects PD engines between 1998 and 2010, regardless of size.

The solenoids of the mechatronics unit wear out: slow or harsh shifting, then limp mode. A characteristic sign is the partial or complete loss of reverse. Wear of the clutch pack or the wrong spring force causes jerking and slipping. Because of the wet design it fails less often and at higher mileage than the dry DQ200, but when it does fail, it is expensive.

The internal springs of the flywheel tire, and the two discs knock against each other. The signs are a rattling or knocking from the bellhousing at idle and when releasing the clutch pedal, and vibration through the floor. If the clutch slips without a burnt smell, that also points to the flywheel. It is worth replacing in time: a disintegrated flywheel can destroy the bellhousing too. At a clutch replacement the two go together anyway.

The ABS control unit fails. First the ABS and ESP lights come on intermittently, then they stay on, and the stability control drops out. The fault typically appears with code `01435`: that points at the controller of the hydraulic brake unit. The unit can often be refurbished, because the fault is in the soldering. A new controller is not always needed.

The first series Touran fails the roadworthiness test for rust more often than average, and the reports single out the tailgate. The corrosion starts along the edge and the seams, initially only as blistering paint. Added to that, oil leaks are above average on every model year and engine version, which contaminates the metal from below.

The rubber seals of the rear doors age and become porous, and the sunroof drains block up. The water gets into the rear footwell and the side wall of the boot; it stays under the carpet, so it goes unnoticed for a long time. The rear is full of electronics and trim, and the connectors corrode.

The PD injectors (on the 1.4, 1.9 and 2.0 TDI alike) are driven by the camshaft itself, against more than 2,000 bar. That wears the lobes and the rockers quickly: first a knocking noise, then a rough idle, hard starting and loss of power. The cause is the wrong oil: the PD engine requires a 5W-40 lubricant to the VW 505.01 specification, with PD approval. A plain synthetic is not enough, and on an everyday 5W-30 the lobes can wear through.

The vanes of the variable geometry turbo are glued together by soot and oil arriving through the EGR. First you get overboost or a lack of boost, then loss of power above 2,000 rpm, and finally limp mode. Caught in time it is enough to remove the turbo, clean it and fit a new actuator rod. Short urban trips and gentle, low rev driving speed up the deposits.

The G62 sensor tells the engine control unit how hot the coolant is. If it is faulty, the control unit thinks a warm engine is cold, and runs it rich: hard warm or cold starting, a rough idle, markedly increased fuel consumption, and a dash temperature gauge that jumps around or never reaches its usual reading. The part is cheap and can be replaced in half an hour: the trouble is that many people do not recognise it and replace an injector or a lambda sensor instead. If the fault persists, the rich mixture can destroy the catalytic converter too.

The dash shows "Error: Workshop! Only leave vehicle in position P" with an audible warning. The message appears in whatever language the car is set to, for example "Fehler: Werkstatt! Fahrzeug nur in Stellung P verlassen" in German.

The G28 sensor drops out as it heats up. While driving the car stops, then starts again after a few minutes. When warm it starts with difficulty or not at all, while cold it starts, so the workshop often cannot reproduce it. The fault code does not always stay stored either.