BMW X5 X5 xDrive50i common faults.

2013–2018, SUV, petrol, 450 HP.

The fault list covers: N63B44 engine, ZF8HP70 transmission.

What you save stays on this device only. My saves

7 fault write-ups. All are important. 10 recalls.

If you know the year, pick it. Faults for other years drop out of the list.

Before you buy

Known faults

7 important faults

critical2

N63 V8: failing piezo injectors and hydraulic lock in the cylinder

critical

On this engine the injectors were also listed as parts to be replaced in the maker's own programme, which means their failure is a known one. A faulty injector puts too much fuel into the cylinder. The liquid cannot be compressed, so the piston hits it on its way up: this is hydraulic lock, and it can damage the connecting rod bearing and the connecting rod as well. The early sign is rough running and hard starting. The fault can start from 60,000 km. The maker ran a separate programme for this engine, called the Customer Care Package, from December 2014. The franchised dealers had to check seven parts: the timing chain, the fuel injectors, the mass air flow sensor, the crankcase vent lines, the battery, the vacuum pump and the low pressure fuel sensor. These had to be replaced free of charge, even if the car had already fallen out of the four-year, 50,000-mile warranty. The same programme also shortened the oil change interval: 10,000 miles or one year instead of 15,000 miles or two years. Before buying it is therefore worth asking whether this programme was carried out on the car.

above 60,000 km

What to check

Ask whether the Customer Care Package was carried out, and whether the injectors were replaced
Start the engine cold and watch for hard starting and rough running
Read the fault memory and look for a code reporting a misfire on a specific cylinder

2 more steps in the write-up

N63 V8: a stretching timing chain and broken guides blocking the oil system

critical

The timing chain stretches between 80,000 and 120,000 km, and the plastic chain guides break. The broken pieces end up in the sump and block the lubrication system. From then on the engine is starved of oil, which takes the bearings and the turbochargers with it. The early sign is a metallic rattling from the front of the engine on a cold start. The stretching of the chain also features in the American class actions, alongside the extreme oil consumption. The maker ran a separate programme for this engine, called the Customer Care Package, from December 2014. The franchised dealers had to check seven parts: the timing chain, the fuel injectors, the mass air flow sensor, the crankcase vent lines, the battery, the vacuum pump and the low pressure fuel sensor. These had to be replaced free of charge, even if the car had already fallen out of the four-year, 50,000-mile warranty. The same programme also shortened the oil change interval: 10,000 miles or one year instead of 15,000 miles or two years. Before buying it is therefore worth asking whether this programme was carried out on the car.

between 80,000 and 120,000 km

What to check

Start the engine cold and listen for metallic rattling from the front of the engine
Ask whether the Customer Care Package was carried out, and whether the chain was replaced
Read the fault memory and look for a code reporting a camshaft position deviation

2 more steps in the write-up

expensive5

XDrive transfer case (ATC): binding in corners, plastic actuator gear

expensive

The heart of the four wheel drive in the longitudinal engine BMW X models (X3, X5 and the X1 E84) is the ATC transfer case. It has two faults, and you can feel both while driving.

Show the rest

The first is wear of the clutch pack and the fluid: in a slow, tight corner (a car park, a roundabout) the car jerks and "hops", as if the drive grabbed and let go. You can also get a jerk when pulling away on a slope. The second is the plastic actuator gear: the position signal is lost, the brake, ABS and 4x4/DSC lights come on together on the dash, and a clicking is audible from the transfer case when you switch the ignition off.

Workshops often propose a full transfer case replacement straight away. But the plastic gear can be replaced on its own, and the wrong tyre size or a mixed set of tyres also imitates the jerking, because the transfer case then slips continuously. So clear up the tyres and the fault code first, before you pay for a transfer case replacement.

between 72,000 and 175,000 km

What to check

In a slow, tight corner (a car park) watch for jerking, binding and a "skipping" feel
When pulling away on light throttle, can you feel the drivetrain jerk
Watch the dash: 4x4, ABS, DSC and brake lights together point at the actuator

4 more steps in the write-up

N63 V8: the valve stem seals leak and oil consumption is extreme

expensive

The valve stem seals start to lose their sealing from 90,000 km, and oil gets into the combustion chamber along the valve stem. The burning oil lays soot on the piston rings, they start to stick, and from then on the consumption grows further; the lubrication also gets tighter and the exhaust smokes. The scale of the consumption on this engine is extraordinary. In the American class action the plaintiffs report around one litre every 1,200 km, and one of them one litre every 1,600 km. In 2013 the maker issued a new oil consumption standard for this engine in a bulletin, and took the position that this is not a defect: according to it every one of its engines may use that much. The lawsuit points out that with this standard the owner has to top up the oil twenty times before reaching the factory 15,000-mile oil change interval. The maker ran a separate programme for this engine, called the Customer Care Package, from December 2014. The franchised dealers had to check seven parts: the timing chain, the fuel injectors, the mass air flow sensor, the crankcase vent lines, the battery, the vacuum pump and the low pressure fuel sensor. These had to be replaced free of charge, even if the car had already fallen out of the four-year, 50,000-mile warranty. The same programme also shortened the oil change interval: 10,000 miles or one year instead of 15,000 miles or two years. Before buying it is therefore worth asking whether this programme was carried out on the car. The repair means opening the cylinder head, and because of the V layout of the engine on both sides.

above 90,000 km

What to check

Ask how much oil has to be added between two changes, and ask for a figure
Ask whether the Customer Care Package programme was carried out, and ask for the confirmation
Read the service book: the shortened, one-year oil change cycle is expected here

2 more steps in the write-up

Rear air suspension: the back sinks overnight, overworked compressor

expensive

On the E70/F15 (and the air sprung G05) X5 the self levelling air spring on the rear axle starts to leak over time. The characteristic picture: after standing for a long time the back sits lower than the nose; on startup the compressor runs for minutes, the car comes up, then sinks again hours later. Sinking on one side points more to that corner's air spring or to the valve block, while sinking on both points to the shared supply (compressor, dryer, lines).

Show the rest

A "compressor replacement" on its own often does not fix it: if the air spring keeps leaking, the new pump fails soon too. Air suspension is not fitted to every version, so the equipment list has to be checked separately.

The repair starts with finding the leak (soapy water, ride height sensor, valve block), not with replacing parts blind.

above 100,000 km

What to check

Look at the car cold, after standing at least one night: does the back sit lower than the nose, or does one rear corner sink
Listen to the compressor after startup: how long it runs, and whether the back comes up
Measure the arch height at all four corners: a difference means a sensor or a spring fault

3 more steps in the write-up

ZF 8HP automatic: mechatronics unit and connector sleeve leak

expensive

The ZF eight speed automatic (BMW Steptronic 8HP family) has two faults, and you can feel both.

Show the rest

The first is the mechatronics unit: the valve body and the control electronics in one. If the solenoids or the pressure regulation weaken, the gearbox jerks, the D/R engagement is delayed, it logs a gear ratio fault code, and finally drops into limp mode (often staying in 2nd or 3rd).

The second, and often misdiagnosed, is the connector sleeve of the mechatronics unit: the O-ring of the plastic sleeve ages, and ATF leaks from the side of the housing, exactly where the wiring harness enters. This is easy to mistake for a rear crankshaft seal. The trail starts from the driver's side of the housing, not from the clutch side.

On cars built in 2023 there was also a separate safety recall for a welding fault in the mechatronics unit. That is not the same as the wear related sleeve and the valves.

Check the fluid level, the area around the sleeve and the fault codes first; do not accept a "full gearbox replacement" quote straight away.

above 120,000 km

What to check

On the test drive watch for delayed D/R engagement, a jerk when shifting, and limp mode (a stuck gear)
Look at the driver's side of the gearbox housing where the wiring harness enters: an ATF trail from the sleeve is suspect
Do not confuse it with a rear crankshaft seal leak: the direction of the trail decides

3 more steps in the write-up

Powered tailgate: breaking wiring at the hinge, spindle drive

expensive

The automatic tailgate (an option) is covered by a maker service bulletin on the E70: the wiring harness around the hinge wears through, the spindle drive fails, the lock sticks or the connectors corrode. The symptom: the tailgate stops halfway, moves in one direction only, only clicks when you press the button, or the lower part of the split tailgate does not close fully.

Show the rest

The fault is often not the "expensive motor" but the wiring fraying at the hinge. And that can only be found with the trim off. If the seller says "the spindle has already been replaced" but the wiring is damaged, the fault will come back.

This applies only to versions with the powered tailgate.

What to check

Open and close the powered tailgate five times: from the key, the interior button and the button in the boot
Watch whether it stops halfway, reverses, or only clicks at the lock
On a split tailgate, try the closing of the lower part separately: there should be no gap left

2 more steps in the write-up

Official recall10 recallsShow

The manufacturer fixes these for free at a franchised dealer. Ask with the VIN whether it was done.

Most recent: 29 July 2021

21V586000FUEL SYSTEM, DIESEL:DELIVERY:FUEL PUMPFUEL SYSTEM, DIESEL:DELIVERY:FUEL PUMP29 July 2021 · NHTSA (USA)

BMW of North America, LLC (BMW) is recalling certain 2014-2018 328d, 328d xDrive, X5 xDrive35d, 2014-2016 535d, 535d xDrive, 2015 740Ld xDrive, and 2015-2017 X3 xDrive28d vehicles. The high-pressure fuel pump may fail.

Risk: Fuel pump failure can cause an engine stall while driving, increasing the risk of a crash.

Remedy: Dealers will replace the high-pressure fuel pump, free of charge. Owner notification letters were mailed on January 14, 2022. Owners may contact BMW customer service at 1-800-525-7417.

The authority's notice

18V652000EQUIPMENT:ELECTRICALEQUIPMENT:ELECTRICAL20 September 2018 · NHTSA (USA)

BMW of North America, LLC (BMW) is recalling certain 2018 BMW 330e iPerformance, i3 Rex, i3 Sport Rex, X5 xDrive40e, i3 BEV, i3 Sport BEV and 2019 i8 and i8 Roadster vehicles and 2018-2019 530e iPerformance, 530e xDrive iPerformance and 740Le xDrive iPerformance vehicles. Capacitors within the TurboCord Portable Chargers may fail, possibly resulting in a shock hazard or a fire.

Risk: An electrical shock or a fire can increase the risk of injury or death.

Remedy: BMW will notify owners, and dealers will inspect the charging cable, and replace it if necessary, free of charge. The recall began February 22, 2019. Owners may contact BMW customer service at 1-800-525-7417.

The authority's notice

A12/00068/19Safety recallInjuriesno date · EU Safety Gate

The press-in force of the counterbalance shaft’s bearing shells may not have met the specifications, which could cause the counterbalance shaft to become loose. As a result, the engine could be damaged and locked in motion, increasing the risk of an accident.