vinkodex.

BMW Z4 Z4 Roadster sDrive28i High Executive common faults.

2009–2013, convertible, petrol, 245 HP.

The fault list covers: N20B20 engine, ZF6HP-BMW, ZF8HP transmission.

What you save stays on this device only. My saves

5 fault write-ups. 4 important. 6 recalls.

If you know the year, pick it. Faults for other years drop out of the list.

Before you buy

Known faults

4 important faults

critical1

Oil pump chain: the plastic guide disintegrates and blocks the pickup

critical

The oil pump is driven by a separate, smaller chain from the crankshaft, behind the timing chain at the front of the engine. This chain runs on plastic guides, and under heat cycles the plastic cracks, flakes off and finally disintegrates. From then on the chain works against the aluminium, the tension is lost, and the stretch progresses fast.

Show the rest

It causes damage along two paths, and the less known one comes first. The broken pieces of plastic are sucked into the oil pickup tube, block the way of the oil there, and destroy the bearings before the chain has even jumped. The other path is the chain or the tensioner letting go: then the oil pressure disappears within seconds, and the engine can seize without stopping.

The warning is not the lamp. This fault does not always light a warning, so the noise is what to listen for: between 1500 and 2500 revs a high, whistling whine comes from the lower part of the engine, and at a cold start a rattle of one to five seconds is audible. The maker issued its own service bulletin for the whining noise on the N20 and the N26.

On the factory chain the fault is reported above 80 000 miles, that is above roughly 129 000 kilometres, but in the American settlement the maker took it on earlier as well: below 70 000 miles, that is 113 000 kilometres, the full cost, and above 100 000 miles or eight years nothing at all. The affected set is the N20 and N26 engines built between 2012 and 2015.

The repair costs between 4000 and 6000 dollars, because the work on the timing and on the oil pump go together. If someone has replaced the timing chain, the oil pump chain has to be replaced with it: if the job is left half done, the engine has to come apart again in a few years.

above 129,000 km

What to check

  • Rev it to between 1500 and 2500 and listen to the bottom of the engine: a high, whistling noise points here
  • Start it cold and listen for a rattle of one to five seconds
  • Do not wait for a warning light: this fault does not always light a lamp
3 more steps in the write-up

expensive3

Oil filter housing gasket: oil leak onto the belt and the alternator

expensive

A rubber gasket seals the oil filter housing to the block. The gasket hardens over the years, and oil leaks from under the housing. The oil drips onto the drive belt and the alternator.

Show the rest

Three things can happen. The oil stretches the belt and it can jump off (on a single belt engine that means an instant loss of the water pump and the alternator); oil getting into the alternator destroys the windings; and oil reaching the hot exhaust smokes and gives a burnt smell, and the official complaints do include burning smells and smoke.

The leak is visible: five minutes on a lift settles it. The gasket itself is a cheap part; the labour, the ruined belt and the alternator take the money.

between 64,000 and 246,000 kmreported complaints only

What to check

  • On a lift look at the block surface around the oil filter housing: a wet, oily or oily dusty film
  • Look at the drive belt: an oily, cracked, stretched belt is the consequence of the leak
  • Look at the alternator housing from below: an oil trail indicates damage reaching the windings
2 more steps in the write-up

ZF 6HP automatic: mechatronics connector sealing sleeve leaks

expensive

In the ZF six speed automatic (BMW codes GA6HP19Z / GA6HP26Z) the electrical connector of the valve body control leaves the gearbox housing through a plastic sleeve. That sleeve and its seals age, and they let oil through.

Show the rest

The symptom is irregular shifting, a gear slipping at higher revs, limp mode, a drivetrain fault code and a message on the display. The cause is the same in each case: the leak drops the hydraulic pressure, and the valve body cannot close the clutches with enough force.

The sleeve can be replaced without removing the gearbox, you only have to drop the oil pan. If it leaks for a long time, the slipping clutch and the overheating pump take the inside of the gearbox with them, and from then on it is a rebuild. The factory calls the oil a lifetime fill, but in practice the sleeve wears out around 60,000 to 70,000 miles, roughly 100,000 to 115,000 km.

between 100,000 and 200,000 km

What to check

  • On a lift look at the right side of the gearbox housing, above the oil pan: a wet, oily connector is the characteristic picture
  • On the test drive watch the shifts cold and warm: jerking, delay, slipping at higher revs
  • Ask for a fault code read from the gearbox controller: gear ratio fault, pressure regulation
2 more steps in the write-up

ZF 8HP automatic: mechatronics unit and connector sleeve leak

expensive

The ZF eight speed automatic (BMW Steptronic 8HP family) has two faults, and you can feel both.

Show the rest

The first is the mechatronics unit: the valve body and the control electronics in one. If the solenoids or the pressure regulation weaken, the gearbox jerks, the D/R engagement is delayed, it logs a gear ratio fault code, and finally drops into limp mode (often staying in 2nd or 3rd).

The second, and often misdiagnosed, is the connector sleeve of the mechatronics unit: the O-ring of the plastic sleeve ages, and ATF leaks from the side of the housing, exactly where the wiring harness enters. This is easy to mistake for a rear crankshaft seal. The trail starts from the driver's side of the housing, not from the clutch side.

On cars built in 2023 there was also a separate safety recall for a welding fault in the mechatronics unit. That is not the same as the wear related sleeve and the valves.

Check the fluid level, the area around the sleeve and the fault codes first; do not accept a "full gearbox replacement" quote straight away.

above 120,000 km

What to check

  • On the test drive watch for delayed D/R engagement, a jerk when shifting, and limp mode (a stuck gear)
  • Look at the driver's side of the gearbox housing where the wiring harness enters: an ATF trail from the sleeve is suspect
  • Do not confuse it with a rear crankshaft seal leak: the direction of the trail decides
3 more steps in the write-up

cheap repair1

Plastic charge pipe: it goes brittle and cracks at the throttle body

cheap repair

The maker builds the charge pipe out of plastic, and the coupler at the throttle body is the critical point. The material goes brittle from heat cycles, from boost pressure and from the heat of the engine bay, and then it cracks. Three things coincide here: the moulded coupler carries both pressure and movement, the vibration of the engine arrives here through the throttle body, and the spot gets continuous heat load. The crack starts on the inner radius of the coupler. The symptom is a loss of pressure under load: the engine pulls cleanly at part throttle but flattens out at full throttle, and a hissing noise is audible from the engine bay at the same time. A yellow drivetrain warning comes with it, which often disappears after a restart, and sometimes a brief limp mode. One thing is worth knowing: a clean fault memory does not rule the crack out. The pipe has no sensor of its own, so the control unit can only log a boost pressure fault, and the leak is intermittent, appearing only under load. At a viewing two things are visible without tools. On the inner radius of the coupler the hairline crack sometimes comes with dark staining, because the oil mist in the boost air escapes through it. For the same reason a greasy, dark ring can appear at the joint of the coupler. The crack is reported above 80 000 kilometres, and replacing the pipe costs between 100 and 400 euros, because the part itself is not expensive. The most common misdiagnosis against that is replacing the turbocharger, which costs an order of magnitude more, and a pressure test protects against it. The factory repair is the same plastic part, which can crack again at a similar mileage; replaced with an aluminium pipe this failure mode disappears, and the driveability does not change.

above 80,000 km100–400 EUR

What to check

  • Look at the inner radius of the coupler at the throttle body: the hairline crack sometimes comes with dark staining
  • Look for a greasy, dark ring at the joint of the coupler
  • On a motorway slip road at full throttle watch for the loss of pressure and the hissing noise
2 more steps in the write-up

Checklist

BMW Z4 Z4 Roadster sDrive28i High Executive

First what you would check on any car. Then the faults of this model.

Before you buy

Checklist

The printed sheet starts with what you would check on any car. What you tick stays on this device only.

On every car

Ask the owner

Faults of this model

vinkodex.com · Before you buy it, see what can go wrong.

Official recall6 recallsShow

The manufacturer fixes these for free at a franchised dealer. Ask with the VIN whether it was done.

Most recent: 20 October 2023

23V707000ENGINE AND ENGINE COOLING:ENGINEENGINE AND ENGINE COOLING:ENGINE20 October 2023 · NHTSA (USA)

BMW of North America, LLC (BMW) is recalling certain 2010-2012 1 Series Coupe, 1 Series Convertible, 3 Series Sedan, 3 Series Convertible, 2010-2011 3 Series Sportswagon, 3 Series Coupe, 5 Series Sedan, X3 xDrive 28i, X3 xDrive 30i, X5 xDrive30i, and Z4 sDrive30i vehicles. The aluminum bolts that secure the housing for the variable camshaft timing adjustment (VANOS) unit can loosen over time and possibly break.

Risk: Loose or broken VANOS unit bolts can result in an engine stall, increasing the risk of a crash.

Remedy: Dealers will replace the four VANOS bolts, free of charge. Interim letters notifying owners of the safety risk are expected to be mailed December 18, 2023. Owner notification letters were mailed June 19, 2024. Owners may contact BMW customer service at 1-800-525-7417.

The authority's notice

22V119000ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CRANKCASE (PCV)ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CRANKCASE (PCV)2 March 2022 · NHTSA (USA)

BMW of North America, LLC (BMW) is recalling certain 2008-2013 1 Series Coupe (128i); 2007-2013 3 Series Coupe (328i, 328xi, 328i xDrive); 2007-2010 X3 SAV (X3 3.0si, X3 xDrive30i); 2008-2013 1 Series Convertible (128i); 2006-2011 3 Series Sedan (325i, 325xi, 328i, 328xi, 328i xDrive, 330i, 330xi); 2006-2012 3 Series Wagon (328i, 328i xDrive); 2007-2013 3 Series Convertible (328i); 2006-2010 5 Series Sedan (525i, 525xi, 528i, 528xi, 530i, 530xi); 2006-2007 5 Series Wagon (530xi); 2007-2010 X5 SAV (X5 3.0si, X5 xDrive30i); 2006-2008 Z4 Coupe (Z4 3.0si); and 2006-2011 Z4 Roadster (Z4 3.0i, Z4 3.0si, Z4 sDrive30i) vehicles. The heater for the positive crankcase ventilation (PCV) valve may short circuit.

Risk: An electrical short can cause the PCV valve heater to overheat, increasing the risk of a fire while driving or, soon after driving when parked.

Remedy: This recall supersedes and expands previous NHTSA recalls 17V-683 and 19V-273. Dealers will install an electrical wiring harness with fuse protection for the PCV Valve heater in potentially affected vehicles, free of charge. This recall supersedes and expands previous NHTSA recalls 17V-683 and 19V-273. Vehicles previously repaired under the prior recalls will need to come back for the new recall remedy. The remedy is currently being developed. Interim owner notification letters informing owners of the safety risk were mailed on April 1, 2022. Owner notification letters were mailed on July 22, 2022. Owners may contact BMW customer service at 1-800-525-7417.

The authority's notice

17V683000ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CRANKCASE (PCV)ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CRANKCASE (PCV)30 October 2017 · NHTSA (USA)

BMW of North America, LLC (BMW) is recalling certain 2008-2011 128i and 2007-2011 328i, 328xi, 328i xDrive, 525i, 525xi, 528i, 528xi, 530i, 530xi, X3 3.0si, X3 xDrive30i, X5 xDrive30i, Z4 3.0i, Z4 3.0si and Z4 sDrive30i vehicles. The heater for the positive crankcase ventilation (PCV) valve may short circuit.

Risk: An electrical short can cause the parts within the PCV valve to melt, increasing the risk of a fire, even when the vehicle is not in use.

Remedy: BMW will notify owners, and dealers will replace the PCV valve heater, free of charge. Interim letters were mailed on November 27, 2017. Owners will receive a second notification by the end of October 2018. Owners may contact BMW customer service at 1-800-525-7417.

The authority's notice

14V176000ENGINE AND ENGINE COOLING:ENGINEENGINE AND ENGINE COOLING:ENGINE10 April 2014 · NHTSA (USA)

BMW of North America, LLC (BMW) is recalling certain model year 2010-2011 128i Coupe, 128i Convertible, 328i Sedan, 328i xDrive Sedan, 328i Coupe, 328i Convertible, 328i Sports Wagon and Z4 sDrive 30i, 2011-2012 135i Coupe, 135i Convertible, 335i Sedan, X5 xDrive 35i, and X6 xDrive 35i, 2011 335i xDrive Sedan, 335i Coupe, 335i Convertible, 528i Sedan, 535i Sedan, 535i xDrive Sedan, X3 xDrive 28i, and X3 xDrive 35i, 2010 X3 xDrive 30i, and X5 xDrive 30i, 2012 640i Coupe, and 640i Convertible and 2010-2012 535i Gran Turismo vehicles. In the affected vehicles, the bolts that secure the housing for the variable camshaft timing adjustment (VANOS) unit can loosen over time and may possibly break.

Risk: If the bolts loosen or break the engine may have reduced power or stall. An engine stall increases the risk of a crash.

Remedy: BMW will notify owners, and dealers will replace the four VANOS housing bolts for both VANOS units (intake and exhaust), free of charge. In addition, owners of approximately 170,172 model year 2010-2012 BMW vehicles equipped with inline 6 cylinder engines not covered by this recall, will receive an extended warranty to address this condition. The recall began on September 24, 2014. Owners may contact BMW at 1-800-525-7417.

The authority's notice

13V044000ELECTRICAL SYSTEMELECTRICAL SYSTEM7 February 2013 · NHTSA (USA)

BMW is recalling certain model year 2008-2012 1-Series coupes and convertibles manufactured December 2007 through September 2011; and 2007-2011 3-Series coupes and convertibles manufactured March 2007 through October 2011; 2007-2011 3-Series sedans manufactured March 2007 through October 2011; 2007-2011 3-Series sports wagons manufactured March 2007 through June 2011; and 2009-2011 Z4 vehicles manufactured March 2009 through June 2011. In February 2013, BMW recalled 504,545 vehicles. In July 2013, BMW informed the agency that it was adding 1-Series, 3-Series, and Z4 vehicles, representing an additional 12,094 vehicles. The total number of vehicles being recalled is now 516,791. The connector for the positive battery cable connector and the corresponding terminal on the fuse box may degrade over time. Over time, the high current flow and heat from electrical resistance may lead to a breakage of the connection, and a loss of electrical power to the vehicle.

Risk: If there is a loss of electrical power to the vehicle, the vehicle may unexpectedly stall, increasing the risk of a crash.

Remedy: BMW will notify owners, and dealers will replace the positive battery cable connector and secure it with an improved method, free of charge. The recall began on March 13, 2013. Owners may call BMW at 1-800-525-7417 or email BMW at CustomerRelations@bmwusa.com.

The authority's notice

A12/0202/17Safety recallInjuriesno date · EU Safety Gate

The universal joint of the drive shaft might break, causing a sudden loss of propulsion.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

The authority's notice

Engine and transmission

1 engines · 2 transmissions

N20B20

115–180 kW (156–245 HP) · petrol

Model year2011–2017

ZF6HP-BMW · 6-speed automatic, longitudinal (ZF 6HP19/21, BMW GA6HP)

automatic · 6 speed

Torque limit450 Nm
MakerZF

We built the code from the model and the gear count. The factory sheet does not state it. More than one transmission is possible. 6 gears = ZF6HP-BMW, 8 gears = ZF8HP.

Variant data

What is in this version

Factory data

Trim
Z4 Roadster sDrive28i High Executive
Body
convertible
Fuel
petrol
Transmission
automatic
Engine size
1997 cc
Power
180 kW (245 HP)
Drive
RWD
Production
2009–2013

Factory service interval

The manufacturer specifies this for this version. Of the mileage and the time, the one that comes first is the one that counts.

  • Air filter

    • 60,000 km or 4 years

  • Cabin (pollen) filter

    • 30,000 km or 2 years

  • Brake fluid change

    • first: 3 years, then 2 years(first change at 3 years, then every two years)

  • Engine oil and oil filter (BMW condition-based service)

    • LongLife25,000 km or 2 years

  • Automatic gearbox oil (ZF 8HP / 6HP)

    • 160,000 km

  • Spark plugs, petrol

    • 60,000 km or 6 years
All E89 versions

Information, not an expert opinion

We write the descriptions, and we put the source next to them. A person reviews them before they go out. They are still information, not a technical expert opinion.

  • A fault on the list does not mean the car you are looking at has it.
  • A fault missing from the list does not mean the model is fault-free. Write-ups are made model by model. Not all of them are done.
  • You decide whether to buy. This is no substitute for an inspection. That needs a workshop and a history check.
Details in the terms