BMW X7 G07 common faults.

BMW of North America, LLC (BMW) is recalling certain 2026 X6, X7, X5, and X5 Plug-In Hybrid vehicles. The instrument panel may have been manufactured incorrectly and prevent the passenger-side air bag from deploying properly.

Risk: An air bag that does not deploy properly can increase the risk of injury during a crash.

Remedy: Dealers will replace the instrument panel trim, free of charge. The vehicles have not been sold from dealer inventory and therefore, no owner letters will be mailed. Owners may contact BMW customer service at 1-800-525-7417. Vehicle Identification Numbers (VINs) involved in this recall became searchable on NHTSA.gov on December 4, 2025.

The authority's notice

BMW of North America, LLC (BMW) is recalling certain 2020 340I, X6, 2020-2025 840I, 2020-2022 740LI, 2019-2020 X7, and X5 vehicles. After repeated attempts, the starter motor may overheat from an electrical overload.

Risk: An overheated starter motor can ignite nearby combustible material in the engine compartment, increasing the risk of a fire.

Remedy: Dealers will replace the engine starter, free of charge. This recall includes vehicles repaired under recall 24V576 and those owners will need to have their vehicle repaired again. Owner notification letters were mailed February 9, 2026. Owners may contact BMW customer service at 1-800-525-7417. Vehicle Identification Numbers (VINs) involved in this recall became searchable on NHTSA.gov November 17, 2025.

The authority's notice

BMW of North America, LLC (BMW) is recalling certain 2026 X5 Plug-in Hybrid, X5, and X7 vehicles. The windshield may not be sealed properly, which can allow water to enter the power distribution box or electronic control unit.

Risk: Water inside electrical components can lead to electronic function failures, such as a loss of headlights, increasing the risk of a crash. In addition, an electrical short-circuit may occur, increasing the risk of a fire while parked or driving.

Remedy: Dealers will inspect the windshield seal. If any leaks are detected, the seal will be repaired and vehicle control units and wiring will be replaced as necessary, free of charge. Owner notification letters were mailed December 3, 2025. Owners may contact BMW customer service at 1-800-525-7417.

The authority's notice

BMW of North America, LLC is recalling certain 2019-2020 X5, X7, 2020 3 Series Sedan, X6, 2020-2021 7 Series Sedan, 2020 8 Series Convertible, 8 Series Coupe, and 2020 8 Series Gran Coupe vehicles. Please see the recall report for the complete list of models. In the event the starter motor fails, repeated attempts to start the vehicle can cause the starter motor to overheat from an electrical overload.

Risk: A starter motor that overheats can ignite nearby combustible material in the engine compartment, increasing the risk of a fire.

Remedy: Dealers will update the vehicle software, free of charge. Owner notification letters were mailed September 27, 2024. Owners may contact BMW customer service at 1-800-525-7417.

The authority's notice

BMW of North America, LLC (BMW) is recalling certain 2024 X5 sDrive40i, X5 xDrive40i and X7 xDrive40i vehicles. The instrument panel may not have been manufactured properly, which can result in improper air bag deployment or the panel separating during air bag deployment.

Risk: Instrument panel separation during air bag deployment can result in pieces of the panel striking occupants. Improper air bag deployment may not restrain an occupant as intended during a crash. Either of these scenarios can increase the risk of injury.

Remedy: Dealers will replace the instrument panel, free of charge. Owner notification letters were mailed April 16, 2024. Owners may contact BMW customer service at 1-800-525-7417.

The authority's notice

BMW of North America, LLC (BMW) is recalling certain 2023 X5 sDrive40i, xDrive40i, xDrive45e, and X7 xDrive40i vehicles. The windshield may not have been properly bonded to the vehicle which could allow water to enter the vehicle and contact electrical components, possibly resulting in a short-circuit.

Risk: An electrical short-circuit increases the risk of a fire.

Remedy: Dealers will inspect the windshield seal and as necessary, remove and reinstall the windshield with a new seal, free of charge. Owner notification letters were mailed December 30, 2022. Owners may contact BMW customer service at 1-800-525-7417.

The authority's notice

BMW of North America, LLC (BMW) is recalling certain 2023 X7 xDrive40i, and X7 M60i vehicles. In certain vehicle operating conditions, only one of the two front parking lights may remain illuminated. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard number 108, "Lamps, Reflective Devices, and Associated Equipment."

Risk: A loss of illumination from one of the parking lights can reduce visibility, increasing the risk of a crash.

Remedy: Dealers will reprogram the electronic control unit for the front parking lights, free of charge. Owner notification letters were mailed November 18, 2022. Owners may contact BMW customer service at 1-800-525-7417.

The authority's notice

BMW of North America, LLC (BMW) is recalling certain 2019-2022 BMW X7 xDrive40i, X7 Drive50i, X7 M50i vehicles with third-row seats. One or more of the compression springs that lock the backrest may not have been installed properly, and could dislodge or detach.

Risk: In a crash, the seat backrest may not fully lock, increasing the risk of injury.

Remedy: Dealers will inspect the third-row seat and, if necessary, remove and reinstall improperly installed compression springs, and reinstall any missing springs, free of charge. Owner notification letters were mailed November 4, 2022. Owners may contact BMW customer service at 1-800-525-7417.

The authority's notice

BMW of North America, LLC (BMW) is recalling certain 2022 4 Series Gran Coupe (430i, 430i xDrive, M440i xDrive); 2019-2022 X5 sDrive40i, X5 xDrive40i, X5 xDrive50i, X5 M50i, X5M; 2021-2022 X5 xdrive45e; 2020-2022 X6 sDrive40i, X6 xDrive40i, X6 xDrive50i, X6M and 2019-2023 X7 xDrive40i, X7 xDrive50i, X7 M50i, X7 xDrive60i, X7 M60i, X7M, Alpina XB7 vehicles. The roof function control unit may be programmed incorrectly, allowing the sunroof to close without the key fob present inside the vehicle. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard number 118, "Power-Operated Window Systems."

Risk: A sunroof that closes without the key fob present inside the vehicle can increase the risk of injury.

Remedy: Dealers will reprogram the roof function control unit, free of charge. Owner notification letters were mailed June 20, 2022. Owners may contact BMW customer service at 1-800-525-7417.

The authority's notice

BMW of North America, LLC (BMW) is recalling certain 2021 X5 sDrive40i, X5 xDrive50i, X5 M50i, X5 xDrive45e, 2021 X7 xDrive40i, X7 M50i, and XB7 vehicles. The head restraints on the second-row outer seats may be the incorrect type for the vehicle.

Risk: In the event of a crash, the head restraints could detach, and increase the risk of injury.

Remedy: BMW will notify owners, and dealers will inspect the head restraints, and replace them as necessary, free of charge. The recall began May 3, 2021. Owners may contact BMW customer service at 1-800-525-7417.

The authority's notice

BMW of North America, LLC (BMW) is recalling certain 2019-2021 X3 sDrive30i, X3 xDrive30i, X3 M40i, X3M, X4 xDrive30i, X4 M40i, M550i, X4M, X5 sDrive40i, X5 xDrive40i, X5 xDrive50i, X5M, X5 M50i, X7 xDrive40i, X7 xDrive50i, X7 M50i, Alpina XB7, 330i, 330i xDrive, M340i, M340i xDrive, and 8 Series Coupe, Convertible and Grand Coupe, 840i, 840i xDrive, M850i xDrive, M8, 2020-2021 530e, 530e xDrive, 330e, 330e xDrive, 745Le, 745Le xDrive, X5 xDrive45e, X3 xDrive30e, X6 sDrive40i, X6 xDrive40i, X6 xDrive50i, X6 M50i, X6M, 530i, 530i xDrive, 540i, 540i xDrive, M550i xDrive, M5, 740i, 740Li, 740Li xDrive, M760i Drive, M760Li xDrive, 750Li xDrive Alpina, Alpina B7 xDrive, and 2021 4 Series Coupe 430i, 430i xDrive, M440i xDrive vehicles. When shifting into Reverse, a small portion of the rearview image may be obscured, or the screen may not illuminate. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 111, "Rear Visibility."

Risk: If the driver relies on only the rearview camera image, the missing or reduced rearview image view can increase the risk of a crash or injury.

Remedy: BMW will notify owners, and dealers will inspect the rearview camera software and update it if necessary, free of charge. The recall began April 16, 2021. Owners may contact BMW customer service at 1-800-525-7417.

The authority's notice

BMW of North America, LLC (BMW) is recalling certain 2020-2021 8 Series Coupe, Grand Coupe and convertible 840i, 840i xDrive, M850i xDrive, M8 and 740 Li, 740 Li xDrive, 750 Li xDrive, M760 Li xDrive, X6 sDrive40i, X6 xDrive40i, X6 xdrive50i, X6 M50i, X6M, and 2019-2021 X5 sDrive40i, X5 xDrive40i, X5 xDrive50i, X5 M50i, X5M, X7 xDrive40i, X7 xDrive50i, X7 M50i, and 2021 M3, M3 Competition, M4 Coupe, M4 Competition Coupe, X5 xDrive45e, 745 Le xDrive. The rotor and shaft within the integrated brake system may not have been welded properly and could separate during a hard braking event, possibly resulting in a loss of the Antilock Brake System (ABS) and braking assistance.

Risk: A loss of ABS and a reduction in braking assistance can increase the risk of a crash.

Remedy: BMW will notify owners, and dealers will replace the integrated brake system, free of charge. Owner notification letters were mailed on May 25, 2021. Owners may contact BMW customer service at 1-800-525-7417.

The authority's notice

BMW of North America, LLC (BMW) is recalling certain 2021 X5 sDrive40i, X5 xDrive40i, X5M, X5 xDrive45e, X6 sDrive40i, X6 xDrive40i, X7 xDrive40i, X7 M50i vehicles. The steering column shaft's universal joint connection may not have been tightened to specifications, and can become loose.

Risk: A loose steering column shaft universal joint connection can affect vehicle handling and control, increasing the risk of a crash.

Remedy: BMW will notify owners, and dealers will inspect and, depending upon the inspection, either the bolt will be replaced and tightened to specifications, or the steering column shaft, universal joint, and bolt will be replaced and tightened to specifications, free of charge. The recall began March 30, 2021. Owners may contact BMW customer service at 1-800-525-7417.

The authority's notice

BMW of North America, LLC (BMW) is recalling certain 2021 M340i xDrive, M440i xDrive Coupe, 530i, 530i xDrive, 540i, 540i xDrive, 740Li, 740Li xDrive, 840i Gran Coupe, 840i xDrive Gran Coupe, X5 sDrive40i, X5 xDrive40i, X6 sDrive40i, X6 xDrive40i, and X7 xDrive40i vehicles. The connection between the 48-Volt battery and the starter-generator may not have been assembled properly, which can cause increased electrical resistance at the connections.

Risk: Increased electrical resistance can increase the risk of a fire.

Remedy: BMW will notify owners, and dealers will inspect the connection between the 48-Volt battery and the starter-generator assembly, replacing it if necessary, free of charge. The recall is expected to begin April 12, 2021. Owners may contact BMW customer service at 1-800-525-7417.

The authority's notice

BMW of North America, LLC (BMW) is recalling certain 2020 X5 sDrive40i, xDrive40i, X5 M50i, X5M, X7 xDrive40i, X7 M50i, X6 xDrive40i, X6 M50i and X6M vehicles and 2021 X5 xDrive45e vehicles. The weld between the front axle support and the right front control arm bearing bracket may separate.

Risk: If the weld between the front axle support and the right front control arm bearing bracket separates, vehicle handling and control may be affected, increasing the risk of a crash.

Remedy: BMW will notify owners, and dealers will replace the front axle support, free of charge. The recall began December 18, 2020. Owners may contact BMW customer service at 1-800-525-7417.

The authority's notice

BMW of North America, LLC (BMW) is recalling certain 2020-2021 X5 sDrive40i, xDrive40i, xDrive50i, X5 M50i, X5M, X6 sDrive40i, xDrive40i, X6 M50i, X6M, X7 M50i and 2021 X5 xDrive45e vehicles. The headlamps may allow a blue light to illuminate. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard number 108, "Lamps, Reflective Devices, and Associated Equipment."

Risk: Oncoming drivers may be confused by the blue light of approaching vehicles, which could potentially increase the risk of a crash.

Remedy: BMW will notify owners, and dealers will inspect the headlamps and, if necessary, replace them, free of charge. The recall began October 30, 2020. Owners may contact BMW customer service at 1-800-525-7417.

The authority's notice

BMW of North America, LLC (BMW) is recalling certain X7 xDrive40i and M50i vehicles. The tire information labels may contain tire size and cold tire inflation pressure information that does not match the specific tires that were installed on these vehicles. As such, these vehicles fail to conform to Federal Motor Vehicle Safety Standard number 110, "Tire Selection and Rims."

Risk: The vehicle operator may be confused by the tire information on the label and this could lead to the installation of an inappropriate size tire and/or inflation pressure, potentially increasing the risk of a crash.

Remedy: BMW will notify owners, and dealers will replace the tire information label, free of charge. The recall began October 26, 2020. Owners may contact BMW customer service at 1-800-525-7417.

The authority's notice

BMW of North America, LLC (BMW) is recalling certain 2020 X5 sDrive 40i, X5 xDrive 40i and one X7 xDrive 40i vehicle. The starter motor may have an extra bolt that could potentially fall into the transmission housing and cause an engine stall.

Risk: An engine stall increases the risk of a crash.

Remedy: BMW will notify owners, and dealers will inspect the starter motor for the extra bolt, removing it if necessary. Dealers will also inspect the starter for damage, and check if the bolt has fallen into the transmission housing, replacing any damaged parts as necessary. All repairs will be performed free of charge. The recall began on October 2, 2020. Owners may contact BMW customer service at 1-800-525-7417.

The authority's notice

BMW of North America, LLC (BMW) is recalling certain 2020 X7 xDrive40i and X7 xDrive50i vehicles. The rear reflex reflectors may not reflect an adequate amount of light. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 108, "Lamps, Reflective Devices, and Associated Equipment."

Risk: An inadequate amount of reflected light will decrease the vehicle's visibility to other drivers, increasing the risk of a crash.

Remedy: BMW will notify owners, and dealers will replace both rear reflex reflectors, free of charge. The recall began March 30, 2020. Owners may contact BMW customer service at 1-800-525-7417.

The authority's notice

BMW of North America, LLC (BMW) is recalling certain 2020 X5 sDrive40i, X5 xDrive40i, X5 M50i, X7 xDrive40i and X7 M50i vehicles. The steering rack pinion teeth may break under load, resulting in a loss of steering control.

Risk: A loss of steering control increases risk of a crash.

Remedy: BMW will notify owners, and dealers will replace the steering rack, free of charge. The recall began August 21, 2019. Owners may contact BMW customer service at 1-800-525-7417.

The authority's notice

BMW of North America, LLC (BMW) is recalling certain 2019 X5 xDrive50i and X7 xDrive40i vehicles. The left side wheel bolts may have been insufficiently tightened and may loosen over time.

Risk: Loose bolts may allow a wheel to detach from the vehicle, increasing the risk of a crash.

Remedy: BMW will notify owners, and dealers will replace and tighten the left side wheel bolts, free of charge. The recall began July 16, 2019. Owners may contact BMW customer service at 1-800-525-7417.

The authority's notice

BMW of North America, LLC (BMW) is recalling certain 2020 750i xDrive, 2019 M850i xDrive Coupe, M850i xDrive Convertible, X5 xDrive50i, X7 xDrive50i, and M5 vehicles. The high pressure fuel pump may not have been properly attached to the engine, which may cause the fuel pump flange to crack, resulting in a fuel leak.

Risk: A fuel leak in the presence of an ignition source can increase the risk of a fire.

Remedy: BMW will notify owners, and dealers will replace the high pressure fuel pumps, free of charge. The recall began August 27, 2019. Owners may contact BMW customer service at 1-800-525-7417.

The authority's notice

BMW of North America, LLC (BMW) is recalling certain 2019 X7 xDrive40i and X7 xDrive50i vehicles. The driver and passenger head air bags may not have been properly aligned with the trim during installation.

Risk: The head air bags may be impaired during deployment, increasing the risk of injury.

Remedy: BMW will notify owners, and dealers will inspect and, as necessary, reinstall the head air bags, free of charge. The recall began July 18, 2019. Owners may contact BMW customer service at 1-800-525-7417.

The authority's notice

BMW of North America, LLC is recalling certain 2019 BMW X7 xDrive40i and X7 xDrive50i vehicles equipped with the "business lounge seat" option. The attachment bolts between the seat adapter and the vehicle may not have been properly tightened.

Risk: If the bolts were not properly tightened, in the event of a crash, the occupants may have an increased risk of injury.

Remedy: None of the affected vehicles have been sold and are quarantined on dealer lots. BMW dealers will replace the attachment bolts for the seat adapter, free of charge. The recall began on February 27, 2019. Owners may contact BMW's customer service at 1-800-525-7417.

The authority's notice

The steering spindle may not have been properly bolted and could become detached. As a result the steering control would be lost, increasing the risk of an accident.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

The authority's notice

Defective hydraulic unit of the braking system may cause a limited braking support and increased braking distance. Moreover, in such cases the ABS system would not be available. This will lead to increased risk of an accident.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

The authority's notice

The dashboard in the affected vehicles may not have been manufactured to the manufacturer specifications. In the event of an accident, the passenger side airbag may not deploy as intended which could increase the risk of injury to the front passenger. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

The authority's notice

The integrated braking system could be compromised, which could lead to an unexpected failure of the hydraulic braking assistance, thereby requiring greater pressure on the brake pedal. This can result in a longer braking distance, as well as failure of the Anti-lock Braking System (ABS) and the Dynamic Stability Control (DSC), increasing the risk of an accident. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

The authority's notice

Due to a faulty installation of the compression springs of the lock in the third seat row, the backrest may not be fully locked. This could lead to an increased risk of injury in the event of an accident. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

The authority's notice

Due to defective welding, the push bars on the front axle beam may become detached. Moreover, a failure of the welding quality may result in a crack of the bearing bracket. This could lead to loss of wheel control, increasing the risk of an accident.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

The authority's notice

The gas generator in knee airbag modules was not properly inserted into the air cushion, resulting in the cushion failing to unfold sufficiently. As a result, it may not be able to deploy correctly in the event of an accident, leading to a reduction in the restraint effect, increasing the risk of injury to the occupants. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

The authority's notice

The software-based overload protection function cannot sufficiently prevent the starter being overloaded in the event of repeated long start-up attempts. The starter may overheat or sparks may be produced as a result of an increased current flow. This increases the risk of a fire. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

The authority's notice

The screw fitting used to attach the front left-hand seat and/or safety belt may not have been tightened with the correct torque. This could affect the attachment of the seat and/or safety belt, increasing the risk of injury in the event of an accident.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

The authority's notice

The head airbags may be incorrectly installed. This may result in insufficient deployment of the airbags in the event of an accident, increasing the risk of injuries.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

The authority's notice

Due to inadequate screwing the high-pressure pump could become detached and fuel may leak out. This could lead to engine failure and to increased risk of the vehicle catching fire.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

The authority's notice

The nuts on the left-hand side wheels may not have been tightened in accordance with the specifications. This may cause a wheel to detach from the vehicle, increasing the risk of an accident.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

The authority's notice

The hollow shaft of the servomotor was not welded correctly. The weld may not be able to withstand high braking pressure build-up and may break. In this case, the reduced braking performance requires greater force and the braking distance may increase. In addition, the ABS and DSC brake control systems are not assisted. This increases the risk of an accident. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

The authority's notice

The engine starter’s electrical contacts may overheat and cause the vehicle to start improperly. Continued starting attempts can intensify the overheating and ignite surrounding components, potentially leading to a vehicle fire while driving or shortly after parking. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

The authority's notice

Water may come into contact with the starter relay and gradually cause corrosion. This could affect the electrical connection inside the relay and make the engine difficult to start. It may also result in a short circuit and could cause the starter to overheat leading to a fire when the vehicle is in motion or when it is parked with the ignition off. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

The authority's notice