BMW X7 X7 xDrive40i common faults.

2022–, SUV, petrol, 380 HP.

The fault list covers: B58B30M2 engine, ZF8HP70 transmission.

What you save stays on this device only. My saves

6 fault write-ups. 5 important. 39 recalls.

If you know the year, pick it. Faults for other years drop out of the list.

Before you buy

Known faults

5 important faults

critical1

Electric water pump: silent failure, immediate overheating

critical

In these engines the water pump is not belt driven but has its own electric motor. It gains on fuel consumption, but it opens a new failure path: the pump or its electronics often simply stops with no warning. Measured in the official complaints, the typical mileage is 161,000 km (a tenth of the complaints already at 81,000, a tenth only above 257,000 km). So the common wisdom of "around 100,000 km" is early: most of the failures happen between 130,000 and 250,000 km.

Show the rest

With a belt driven pump the flow weakens gradually, here the circulation stops in an instant. In urban traffic the temperature crosses the limit within minutes, the cylinder head distorts, and the repair is an engine rebuild.

Replacing a still good pump at around 120,000 to 150,000 km costs less than repairing an overheated engine. If the replacement is already in the service book, the pump has already been changed.

between 81,000 and 257,000 km

What to check

Watch the coolant temperature gauge after startup: it should settle evenly, not jump around
Standing still with a warm engine, listen for whether the cooling fan and the pump are working
Ask for a fault code read: codes pointing at coolant flow belong here

2 more steps in the write-up

expensive4

Oil filter housing gasket: oil leak onto the belt and the alternator

expensive

A rubber gasket seals the oil filter housing to the block. The gasket hardens over the years, and oil leaks from under the housing. The oil drips onto the drive belt and the alternator.

Show the rest

Three things can happen. The oil stretches the belt and it can jump off (on a single belt engine that means an instant loss of the water pump and the alternator); oil getting into the alternator destroys the windings; and oil reaching the hot exhaust smokes and gives a burnt smell, and the official complaints do include burning smells and smoke.

The leak is visible: five minutes on a lift settles it. The gasket itself is a cheap part; the labour, the ruined belt and the alternator take the money.

between 64,000 and 246,000 kmreported complaints only

What to check

On a lift look at the block surface around the oil filter housing: a wet, oily or oily dusty film
Look at the drive belt: an oily, cracked, stretched belt is the consequence of the leak
Look at the alternator housing from below: an oil trail indicates damage reaching the windings

2 more steps in the write-up

VANOS solenoid valve: a clogging filter screen and late camshaft adjustment

expensive

VANOS adjusts the position of the camshaft with the pressure of the engine oil, and a solenoid valve metres that pressure. The valve sits in the oil circuit, and a fine filter screen protects the spool inside it from larger particles. That screen clogs with carbon and deposits: less oil flows through, and VANOS then adjusts late or does not move at all. The symptoms are a rough idle, rough running, a lack of torque at low revs and higher fuel consumption, because the valve timing is off. A short metallic clacking can also come on a cold start and goes quiet after 10 to 20 seconds. The engine warning light comes on with a camshaft fault code, and depending on the severity the engine control unit switches to limp mode. The fault code narrows down the cause. P0010 and P0013 typically mean the solenoid valve itself, that is a circuit fault or reduced oil flow through the clogged screen. P0011 and P0014 point more to a mechanical cause: a stretched timing chain or a worn adjuster. P0012 and P0015 report late camshaft control, whose common cause is slow pressure build-up at the adjuster, so again the dirty valve. The valve itself is a small part, between 50 and 120 euro, and with a clean screen cleaning is often enough; replacing the whole adjuster, by contrast, is a four-figure job. The reported repairs ran between 80 and 1,200 euro, depending on whether cleaning is enough and how many valves are affected. The main cause of the screen clogging is a stretched oil change interval and carbon-laden oil.

between 70,000 and 120,000 km80–1,200 EUR

What to check

Read the fault memory and note the exact code: P0010 and P0013 point to the valve
If P0011 or P0014 is stored, the timing chain has to be checked as well
Start the engine cold and listen for metallic clacking in the first 10 to 20 seconds

2 more steps in the write-up

Crankcase ventilation (CCV) in the valve cover: oil consumption, rough running

expensive

The crankcase ventilation leads the gas that forms in the crankcase back to the intake and separates the oil out of it on the way. If the system clogs or the membrane tears, the pressure cannot get away: it finds a way out past the seals, or it pushes the oil through the piston rings. This is where the oil consumption comes from, and the oil that appears around the valve cover gasket. In the other direction a faulty breather takes unmetered air into the intake, and that is what makes the idle rough, the throttle response hesitant and the running coarse. Starting also gets harder, and in an extreme case the engine stalls at idle. Two characteristic signs help: weak or absent suction at the oil filler with the engine running, and noticeably rough running around 3,000 rpm. The hose at the rear of the valve cover can also let oil out. The sound insulation then soaks itself with oil, and oil gets everywhere in the engine bay. On the six-cylinder engines the breather is built into the valve cover, so the repair is replacing the cover or the whole oil separator together with the hoses, between 80 and 900 euro.

between 80,000 and 150,000 km80–900 EUR

What to check

With the engine running unscrew the oil filler cap: weak or absent suction is a sign
Look around the valve cover and at the rear of the engine bay for oil traces
Watch the idle, and the rough running around 3,000 rpm

2 more steps in the write-up

ZF 8HP automatic: mechatronics unit and connector sleeve leak

expensive

The ZF eight speed automatic (BMW Steptronic 8HP family) has two faults, and you can feel both.

Show the rest

The first is the mechatronics unit: the valve body and the control electronics in one. If the solenoids or the pressure regulation weaken, the gearbox jerks, the D/R engagement is delayed, it logs a gear ratio fault code, and finally drops into limp mode (often staying in 2nd or 3rd).

The second, and often misdiagnosed, is the connector sleeve of the mechatronics unit: the O-ring of the plastic sleeve ages, and ATF leaks from the side of the housing, exactly where the wiring harness enters. This is easy to mistake for a rear crankshaft seal. The trail starts from the driver's side of the housing, not from the clutch side.

On cars built in 2023 there was also a separate safety recall for a welding fault in the mechatronics unit. That is not the same as the wear related sleeve and the valves.

Check the fluid level, the area around the sleeve and the fault codes first; do not accept a "full gearbox replacement" quote straight away.

above 120,000 km

What to check

On the test drive watch for delayed D/R engagement, a jerk when shifting, and limp mode (a stuck gear)
Look at the driver's side of the gearbox housing where the wiring harness enters: an ATF trail from the sleeve is suspect
Do not confuse it with a rear crankshaft seal leak: the direction of the trail decides

3 more steps in the write-up

cheap repair1

Plastic charge pipe: it goes brittle and cracks at the throttle body

cheap repair

The maker builds the charge pipe out of plastic, and the coupler at the throttle body is the critical point. The material goes brittle from heat cycles, from boost pressure and from the heat of the engine bay, and then it cracks. Three things coincide here: the moulded coupler carries both pressure and movement, the vibration of the engine arrives here through the throttle body, and the spot gets continuous heat load. The crack starts on the inner radius of the coupler. The symptom is a loss of pressure under load: the engine pulls cleanly at part throttle but flattens out at full throttle, and a hissing noise is audible from the engine bay at the same time. A yellow drivetrain warning comes with it, which often disappears after a restart, and sometimes a brief limp mode. One thing is worth knowing: a clean fault memory does not rule the crack out. The pipe has no sensor of its own, so the control unit can only log a boost pressure fault, and the leak is intermittent, appearing only under load. At a viewing two things are visible without tools. On the inner radius of the coupler the hairline crack sometimes comes with dark staining, because the oil mist in the boost air escapes through it. For the same reason a greasy, dark ring can appear at the joint of the coupler. The crack is reported above 80 000 kilometres, and replacing the pipe costs between 100 and 400 euros, because the part itself is not expensive. The most common misdiagnosis against that is replacing the turbocharger, which costs an order of magnitude more, and a pressure test protects against it. The factory repair is the same plastic part, which can crack again at a similar mileage; replaced with an aluminium pipe this failure mode disappears, and the driveability does not change.

above 80,000 km100–400 EUR

What to check

Look at the inner radius of the coupler at the throttle body: the hairline crack sometimes comes with dark staining
Look for a greasy, dark ring at the joint of the coupler
On a motorway slip road at full throttle watch for the loss of pressure and the hissing noise

2 more steps in the write-up

Official recall39 recallsShow

The manufacturer fixes these for free at a franchised dealer. Ask with the VIN whether it was done.

Most recent: 4 December 2025

25V837000AIR BAGS:CRITICAL FASTENERSAIR BAGS:CRITICAL FASTENERS4 December 2025 · NHTSA (USA)

BMW of North America, LLC (BMW) is recalling certain 2026 X6, X7, X5, and X5 Plug-In Hybrid vehicles. The instrument panel may have been manufactured incorrectly and prevent the passenger-side air bag from deploying properly.

Risk: An air bag that does not deploy properly can increase the risk of injury during a crash.

Remedy: Dealers will replace the instrument panel trim, free of charge. The vehicles have not been sold from dealer inventory and therefore, no owner letters will be mailed. Owners may contact BMW customer service at 1-800-525-7417. Vehicle Identification Numbers (VINs) involved in this recall became searchable on NHTSA.gov on December 4, 2025.

We could not check this: model year. The authority's notice

25V644000ELECTRICAL SYSTEM:STARTER ASSEMBLYELECTRICAL SYSTEM:STARTER ASSEMBLY25 September 2025 · NHTSA (USA)

BMW of North America, LLC (BMW) is recalling certain 2020 340I, X6, 2020-2025 840I, 2020-2022 740LI, 2019-2020 X7, and X5 vehicles. After repeated attempts, the starter motor may overheat from an electrical overload.

Risk: An overheated starter motor can ignite nearby combustible material in the engine compartment, increasing the risk of a fire.

Remedy: Dealers will replace the engine starter, free of charge. This recall includes vehicles repaired under recall 24V576 and those owners will need to have their vehicle repaired again. Owner notification letters were mailed February 9, 2026. Owners may contact BMW customer service at 1-800-525-7417. Vehicle Identification Numbers (VINs) involved in this recall became searchable on NHTSA.gov November 17, 2025.

We could not check this: model year. The authority's notice

25V556000VISIBILITY:WINDSHIELD:CRITICAL FASTENERSVISIBILITY:WINDSHIELD:CRITICAL FASTENERS27 August 2025 · NHTSA (USA)

BMW of North America, LLC (BMW) is recalling certain 2026 X5 Plug-in Hybrid, X5, and X7 vehicles. The windshield may not be sealed properly, which can allow water to enter the power distribution box or electronic control unit.

Risk: Water inside electrical components can lead to electronic function failures, such as a loss of headlights, increasing the risk of a crash. In addition, an electrical short-circuit may occur, increasing the risk of a fire while parked or driving.

Remedy: Dealers will inspect the windshield seal. If any leaks are detected, the seal will be repaired and vehicle control units and wiring will be replaced as necessary, free of charge. Owner notification letters were mailed December 3, 2025. Owners may contact BMW customer service at 1-800-525-7417.

We could not check this: model year. The authority's notice

24V576000ELECTRICAL SYSTEM:STARTER ASSEMBLYELECTRICAL SYSTEM:STARTER ASSEMBLY1 August 2024 · NHTSA (USA)

BMW of North America, LLC is recalling certain 2019-2020 X5, X7, 2020 3 Series Sedan, X6, 2020-2021 7 Series Sedan, 2020 8 Series Convertible, 8 Series Coupe, and 2020 8 Series Gran Coupe vehicles. Please see the recall report for the complete list of models. In the event the starter motor fails, repeated attempts to start the vehicle can cause the starter motor to overheat from an electrical overload.

Risk: A starter motor that overheats can ignite nearby combustible material in the engine compartment, increasing the risk of a fire.

Remedy: Dealers will update the vehicle software, free of charge. Owner notification letters were mailed September 27, 2024. Owners may contact BMW customer service at 1-800-525-7417.

We could not check this: model year. The authority's notice

24V138000STRUCTURE:INTERIOR PANELS:DASHBOARDSTRUCTURE:INTERIOR PANELS:DASHBOARD23 February 2024 · NHTSA (USA)

BMW of North America, LLC (BMW) is recalling certain 2024 X5 sDrive40i, X5 xDrive40i and X7 xDrive40i vehicles. The instrument panel may not have been manufactured properly, which can result in improper air bag deployment or the panel separating during air bag deployment.

Risk: Instrument panel separation during air bag deployment can result in pieces of the panel striking occupants. Improper air bag deployment may not restrain an occupant as intended during a crash. Either of these scenarios can increase the risk of injury.

Remedy: Dealers will replace the instrument panel, free of charge. Owner notification letters were mailed April 16, 2024. Owners may contact BMW customer service at 1-800-525-7417.

We could not check this: model year. The authority's notice

22V820000VISIBILITY:WINDSHIELDVISIBILITY:WINDSHIELD2 November 2022 · NHTSA (USA)

BMW of North America, LLC (BMW) is recalling certain 2023 X5 sDrive40i, xDrive40i, xDrive45e, and X7 xDrive40i vehicles. The windshield may not have been properly bonded to the vehicle which could allow water to enter the vehicle and contact electrical components, possibly resulting in a short-circuit.

Risk: An electrical short-circuit increases the risk of a fire.

Remedy: Dealers will inspect the windshield seal and as necessary, remove and reinstall the windshield with a new seal, free of charge. Owner notification letters were mailed December 30, 2022. Owners may contact BMW customer service at 1-800-525-7417.

We could not check this: model year. The authority's notice

22V725000EXTERIOR LIGHTINGEXTERIOR LIGHTING29 September 2022 · NHTSA (USA)

BMW of North America, LLC (BMW) is recalling certain 2023 X7 xDrive40i, and X7 M60i vehicles. In certain vehicle operating conditions, only one of the two front parking lights may remain illuminated. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard number 108, "Lamps, Reflective Devices, and Associated Equipment."

Risk: A loss of illumination from one of the parking lights can reduce visibility, increasing the risk of a crash.

Remedy: Dealers will reprogram the electronic control unit for the front parking lights, free of charge. Owner notification letters were mailed November 18, 2022. Owners may contact BMW customer service at 1-800-525-7417.

We could not check this: model year. The authority's notice

22V670000SEATSSEATS7 September 2022 · NHTSA (USA)

BMW of North America, LLC (BMW) is recalling certain 2019-2022 BMW X7 xDrive40i, X7 Drive50i, X7 M50i vehicles with third-row seats. One or more of the compression springs that lock the backrest may not have been installed properly, and could dislodge or detach.

Risk: In a crash, the seat backrest may not fully lock, increasing the risk of injury.

Remedy: Dealers will inspect the third-row seat and, if necessary, remove and reinstall improperly installed compression springs, and reinstall any missing springs, free of charge. Owner notification letters were mailed November 4, 2022. Owners may contact BMW customer service at 1-800-525-7417.

We could not check this: model year. The authority's notice

22V267000VISIBILITY:SUN/MOON ROOF ASSEMBLYVISIBILITY:SUN/MOON ROOF ASSEMBLY20 April 2022 · NHTSA (USA)

BMW of North America, LLC (BMW) is recalling certain 2022 4 Series Gran Coupe (430i, 430i xDrive, M440i xDrive); 2019-2022 X5 sDrive40i, X5 xDrive40i, X5 xDrive50i, X5 M50i, X5M; 2021-2022 X5 xdrive45e; 2020-2022 X6 sDrive40i, X6 xDrive40i, X6 xDrive50i, X6M and 2019-2023 X7 xDrive40i, X7 xDrive50i, X7 M50i, X7 xDrive60i, X7 M60i, X7M, Alpina XB7 vehicles. The roof function control unit may be programmed incorrectly, allowing the sunroof to close without the key fob present inside the vehicle. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard number 118, "Power-Operated Window Systems."

Risk: A sunroof that closes without the key fob present inside the vehicle can increase the risk of injury.

Remedy: Dealers will reprogram the roof function control unit, free of charge. Owner notification letters were mailed June 20, 2022. Owners may contact BMW customer service at 1-800-525-7417.

We could not check this: model year. The authority's notice

21V156000SEATS:MID/REAR ASSEMBLY:HEAD RESTRAINTSEATS:MID/REAR ASSEMBLY:HEAD RESTRAINT10 March 2021 · NHTSA (USA)

BMW of North America, LLC (BMW) is recalling certain 2021 X5 sDrive40i, X5 xDrive50i, X5 M50i, X5 xDrive45e, 2021 X7 xDrive40i, X7 M50i, and XB7 vehicles. The head restraints on the second-row outer seats may be the incorrect type for the vehicle.

Risk: In the event of a crash, the head restraints could detach, and increase the risk of injury.

Remedy: BMW will notify owners, and dealers will inspect the head restraints, and replace them as necessary, free of charge. The recall began May 3, 2021. Owners may contact BMW customer service at 1-800-525-7417.

We could not check this: model year. The authority's notice

21V096000BACK OVER PREVENTION: SENSING SYSTEM: CAMERABACK OVER PREVENTION: SENSING SYSTEM: CAMERA19 February 2021 · NHTSA (USA)

BMW of North America, LLC (BMW) is recalling certain 2019-2021 X3 sDrive30i, X3 xDrive30i, X3 M40i, X3M, X4 xDrive30i, X4 M40i, M550i, X4M, X5 sDrive40i, X5 xDrive40i, X5 xDrive50i, X5M, X5 M50i, X7 xDrive40i, X7 xDrive50i, X7 M50i, Alpina XB7, 330i, 330i xDrive, M340i, M340i xDrive, and 8 Series Coupe, Convertible and Grand Coupe, 840i, 840i xDrive, M850i xDrive, M8, 2020-2021 530e, 530e xDrive, 330e, 330e xDrive, 745Le, 745Le xDrive, X5 xDrive45e, X3 xDrive30e, X6 sDrive40i, X6 xDrive40i, X6 xDrive50i, X6 M50i, X6M, 530i, 530i xDrive, 540i, 540i xDrive, M550i xDrive, M5, 740i, 740Li, 740Li xDrive, M760i Drive, M760Li xDrive, 750Li xDrive Alpina, Alpina B7 xDrive, and 2021 4 Series Coupe 430i, 430i xDrive, M440i xDrive vehicles. When shifting into Reverse, a small portion of the rearview image may be obscured, or the screen may not illuminate. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 111, "Rear Visibility."

Risk: If the driver relies on only the rearview camera image, the missing or reduced rearview image view can increase the risk of a crash or injury.

Remedy: BMW will notify owners, and dealers will inspect the rearview camera software and update it if necessary, free of charge. The recall began April 16, 2021. Owners may contact BMW customer service at 1-800-525-7417.

We could not check this: model year. The authority's notice

21V062000SERVICE BRAKES, HYDRAULICSERVICE BRAKES, HYDRAULIC10 February 2021 · NHTSA (USA)

BMW of North America, LLC (BMW) is recalling certain 2020-2021 8 Series Coupe, Grand Coupe and convertible 840i, 840i xDrive, M850i xDrive, M8 and 740 Li, 740 Li xDrive, 750 Li xDrive, M760 Li xDrive, X6 sDrive40i, X6 xDrive40i, X6 xdrive50i, X6 M50i, X6M, and 2019-2021 X5 sDrive40i, X5 xDrive40i, X5 xDrive50i, X5 M50i, X5M, X7 xDrive40i, X7 xDrive50i, X7 M50i, and 2021 M3, M3 Competition, M4 Coupe, M4 Competition Coupe, X5 xDrive45e, 745 Le xDrive. The rotor and shaft within the integrated brake system may not have been welded properly and could separate during a hard braking event, possibly resulting in a loss of the Antilock Brake System (ABS) and braking assistance.

Risk: A loss of ABS and a reduction in braking assistance can increase the risk of a crash.

Remedy: BMW will notify owners, and dealers will replace the integrated brake system, free of charge. Owner notification letters were mailed on May 25, 2021. Owners may contact BMW customer service at 1-800-525-7417.

We could not check this: model year. The authority's notice

21V031000STEERING:COLUMNSTEERING:COLUMN29 January 2021 · NHTSA (USA)

BMW of North America, LLC (BMW) is recalling certain 2021 X5 sDrive40i, X5 xDrive40i, X5M, X5 xDrive45e, X6 sDrive40i, X6 xDrive40i, X7 xDrive40i, X7 M50i vehicles. The steering column shaft's universal joint connection may not have been tightened to specifications, and can become loose.

Risk: A loose steering column shaft universal joint connection can affect vehicle handling and control, increasing the risk of a crash.

Remedy: BMW will notify owners, and dealers will inspect and, depending upon the inspection, either the bolt will be replaced and tightened to specifications, or the steering column shaft, universal joint, and bolt will be replaced and tightened to specifications, free of charge. The recall began March 30, 2021. Owners may contact BMW customer service at 1-800-525-7417.

We could not check this: model year. The authority's notice

20V761000ELECTRICAL SYSTEM:12V/24V/48V BATTERYELECTRICAL SYSTEM:12V/24V/48V BATTERY9 December 2020 · NHTSA (USA)

BMW of North America, LLC (BMW) is recalling certain 2021 M340i xDrive, M440i xDrive Coupe, 530i, 530i xDrive, 540i, 540i xDrive, 740Li, 740Li xDrive, 840i Gran Coupe, 840i xDrive Gran Coupe, X5 sDrive40i, X5 xDrive40i, X6 sDrive40i, X6 xDrive40i, and X7 xDrive40i vehicles. The connection between the 48-Volt battery and the starter-generator may not have been assembled properly, which can cause increased electrical resistance at the connections.

Risk: Increased electrical resistance can increase the risk of a fire.

Remedy: BMW will notify owners, and dealers will inspect the connection between the 48-Volt battery and the starter-generator assembly, replacing it if necessary, free of charge. The recall is expected to begin April 12, 2021. Owners may contact BMW customer service at 1-800-525-7417.

We could not check this: model year. The authority's notice

20V678000SUSPENSION:FRONT:CONTROL ARMSUSPENSION:FRONT:CONTROL ARM4 November 2020 · NHTSA (USA)

BMW of North America, LLC (BMW) is recalling certain 2020 X5 sDrive40i, xDrive40i, X5 M50i, X5M, X7 xDrive40i, X7 M50i, X6 xDrive40i, X6 M50i and X6M vehicles and 2021 X5 xDrive45e vehicles. The weld between the front axle support and the right front control arm bearing bracket may separate.

Risk: If the weld between the front axle support and the right front control arm bearing bracket separates, vehicle handling and control may be affected, increasing the risk of a crash.

Remedy: BMW will notify owners, and dealers will replace the front axle support, free of charge. The recall began December 18, 2020. Owners may contact BMW customer service at 1-800-525-7417.

We could not check this: model year. The authority's notice

20V528000EXTERIOR LIGHTING:HEADLIGHTSEXTERIOR LIGHTING:HEADLIGHTS1 September 2020 · NHTSA (USA)

BMW of North America, LLC (BMW) is recalling certain 2020-2021 X5 sDrive40i, xDrive40i, xDrive50i, X5 M50i, X5M, X6 sDrive40i, xDrive40i, X6 M50i, X6M, X7 M50i and 2021 X5 xDrive45e vehicles. The headlamps may allow a blue light to illuminate. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard number 108, "Lamps, Reflective Devices, and Associated Equipment."

Risk: Oncoming drivers may be confused by the blue light of approaching vehicles, which could potentially increase the risk of a crash.

Remedy: BMW will notify owners, and dealers will inspect the headlamps and, if necessary, replace them, free of charge. The recall began October 30, 2020. Owners may contact BMW customer service at 1-800-525-7417.

We could not check this: model year. The authority's notice

20V514000EQUIPMENT:OTHER:LABELSEQUIPMENT:OTHER:LABELS27 August 2020 · NHTSA (USA)

BMW of North America, LLC (BMW) is recalling certain X7 xDrive40i and M50i vehicles. The tire information labels may contain tire size and cold tire inflation pressure information that does not match the specific tires that were installed on these vehicles. As such, these vehicles fail to conform to Federal Motor Vehicle Safety Standard number 110, "Tire Selection and Rims."

Risk: The vehicle operator may be confused by the tire information on the label and this could lead to the installation of an inappropriate size tire and/or inflation pressure, potentially increasing the risk of a crash.

Remedy: BMW will notify owners, and dealers will replace the tire information label, free of charge. The recall began October 26, 2020. Owners may contact BMW customer service at 1-800-525-7417.

We could not check this: model year. The authority's notice

20V465000POWER TRAIN:AUTOMATIC TRANSMISSIONPOWER TRAIN:AUTOMATIC TRANSMISSION7 August 2020 · NHTSA (USA)

BMW of North America, LLC (BMW) is recalling certain 2020 X5 sDrive 40i, X5 xDrive 40i and one X7 xDrive 40i vehicle. The starter motor may have an extra bolt that could potentially fall into the transmission housing and cause an engine stall.

Risk: An engine stall increases the risk of a crash.

Remedy: BMW will notify owners, and dealers will inspect the starter motor for the extra bolt, removing it if necessary. Dealers will also inspect the starter for damage, and check if the bolt has fallen into the transmission housing, replacing any damaged parts as necessary. All repairs will be performed free of charge. The recall began on October 2, 2020. Owners may contact BMW customer service at 1-800-525-7417.

We could not check this: model year. The authority's notice

20V052000EXTERIOR LIGHTINGEXTERIOR LIGHTING30 January 2020 · NHTSA (USA)

BMW of North America, LLC (BMW) is recalling certain 2020 X7 xDrive40i and X7 xDrive50i vehicles. The rear reflex reflectors may not reflect an adequate amount of light. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 108, "Lamps, Reflective Devices, and Associated Equipment."

Risk: An inadequate amount of reflected light will decrease the vehicle's visibility to other drivers, increasing the risk of a crash.

Remedy: BMW will notify owners, and dealers will replace both rear reflex reflectors, free of charge. The recall began March 30, 2020. Owners may contact BMW customer service at 1-800-525-7417.

We could not check this: model year. The authority's notice

19V631000STEERING:RACK AND PINION:RACKSTEERING:RACK AND PINION:RACK28 August 2019 · NHTSA (USA)

BMW of North America, LLC (BMW) is recalling certain 2020 X5 sDrive40i, X5 xDrive40i, X5 M50i, X7 xDrive40i and X7 M50i vehicles. The steering rack pinion teeth may break under load, resulting in a loss of steering control.

Risk: A loss of steering control increases risk of a crash.

Remedy: BMW will notify owners, and dealers will replace the steering rack, free of charge. The recall began August 21, 2019. Owners may contact BMW customer service at 1-800-525-7417.

We could not check this: model year. The authority's notice

19V541000WHEELS:LUGS/NUTS/BOLTS/STUDSWHEELS:LUGS/NUTS/BOLTS/STUDS23 July 2019 · NHTSA (USA)

BMW of North America, LLC (BMW) is recalling certain 2019 X5 xDrive50i and X7 xDrive40i vehicles. The left side wheel bolts may have been insufficiently tightened and may loosen over time.

Risk: Loose bolts may allow a wheel to detach from the vehicle, increasing the risk of a crash.

Remedy: BMW will notify owners, and dealers will replace and tighten the left side wheel bolts, free of charge. The recall began July 16, 2019. Owners may contact BMW customer service at 1-800-525-7417.

We could not check this: model year. The authority's notice

19V513000FUEL SYSTEM, OTHER:DELIVERY:FUEL PUMPFUEL SYSTEM, OTHER:DELIVERY:FUEL PUMP3 July 2019 · NHTSA (USA)

BMW of North America, LLC (BMW) is recalling certain 2020 750i xDrive, 2019 M850i xDrive Coupe, M850i xDrive Convertible, X5 xDrive50i, X7 xDrive50i, and M5 vehicles. The high pressure fuel pump may not have been properly attached to the engine, which may cause the fuel pump flange to crack, resulting in a fuel leak.

Risk: A fuel leak in the presence of an ignition source can increase the risk of a fire.

Remedy: BMW will notify owners, and dealers will replace the high pressure fuel pumps, free of charge. The recall began August 27, 2019. Owners may contact BMW customer service at 1-800-525-7417.

We could not check this: model year. The authority's notice

19V386000AIR BAGS:SIDE/WINDOWAIR BAGS:SIDE/WINDOW23 May 2019 · NHTSA (USA)

BMW of North America, LLC (BMW) is recalling certain 2019 X7 xDrive40i and X7 xDrive50i vehicles. The driver and passenger head air bags may not have been properly aligned with the trim during installation.

Risk: The head air bags may be impaired during deployment, increasing the risk of injury.

Remedy: BMW will notify owners, and dealers will inspect and, as necessary, reinstall the head air bags, free of charge. The recall began July 18, 2019. Owners may contact BMW customer service at 1-800-525-7417.

We could not check this: model year. The authority's notice

19V135000SEATSSEATS27 February 2019 · NHTSA (USA)

BMW of North America, LLC is recalling certain 2019 BMW X7 xDrive40i and X7 xDrive50i vehicles equipped with the "business lounge seat" option. The attachment bolts between the seat adapter and the vehicle may not have been properly tightened.

Risk: If the bolts were not properly tightened, in the event of a crash, the occupants may have an increased risk of injury.

Remedy: None of the affected vehicles have been sold and are quarantined on dealer lots. BMW dealers will replace the attachment bolts for the seat adapter, free of charge. The recall began on February 27, 2019. Owners may contact BMW's customer service at 1-800-525-7417.

We could not check this: model year. The authority's notice

A12/00307/21Safety recallInjuriesno date · EU Safety Gate

The steering spindle may not have been properly bolted and could become detached. As a result the steering control would be lost, increasing the risk of an accident.