vinkodex.

Ford Galaxy 2.0 TDCi 140hp Titanium common faults.

2010–2015, MPV, diesel, 140 HP.

The fault list covers: QXBA, QXBB, UFBA, UFBB engine, M66, MMT6 transmission.

What you save stays on this device only. My saves

4 fault write-ups. All are important. No recall on the list.

If you know the year, pick it. Faults for other years drop out of the list.

Before you buy

Known faults

4 important faults

M66 manual: worn shift mechanism behind the powerful engines

expensive

The gearbox is reliable and durable, but it sits behind particularly powerful engines, and that shows on the shift mechanism: between 100,000 and 150,000 km it often wears out, which makes shifting stiff, and that is most obvious in winter.

Show the rest

Above 200,000 km the bearings can drone and the dual-mass flywheel can knock. The oil level is worth watching, because leaks are common and the gearbox tolerates a dropping level badly.

between 100,000 and 150,000 km

What to check

  • Set off from cold: every gear must engage without snagging
  • Stop and select reverse: it must not grate or need force
  • At a steady speed, listen for noise: a worn bearing drones
2 more steps in the write-up

MMT6 manual: worn shift mechanism, hard shifting when cold

expensive

The gearbox itself is reliable, but the shift mechanism wears noticeably between 100,000 and 150,000 km. Shifting becomes stiff, and it is most obvious when cold: the lever does not want to find its place, or the gear only goes in with force.

Show the rest

At high mileage the synchros on the first two gears wear out, and then the shift grates. The gearbox comes with a dual-mass flywheel, which is not the most durable part either.

between 100,000 and 150,000 km

What to check

  • Set off from cold: both first and second must engage without snagging
  • Stop and select reverse: it must not grate or need force
  • While rolling, change down into second: this is where worn synchros are audible
2 more steps in the write-up

Injector copper washer: the carbon glues the injector into the head

expensive

The copper washer under the injector is a one-time seal: it is permanently crushed when torqued, so once refitted it can no longer seal. If the seal goes, combustion gas escapes past the injector at over 2000 degrees and over 300 bar, carbonises the engine oil and eats into the seat of the injector. The fault appears at around 150 000 kilometres, but an early failure can also be caused by incorrect torque, a dirty seat and a reused washer.

Show the rest

The escaping gas mixes the unburnt hydrocarbons with the engine oil under the rocker cover, and a hard, coal-like crust bakes out of that. This deposit surrounds the injector and over time glues it into the cylinder head.

The symptoms are easy to recognise. At idle a rhythmic chuffing noise is audible, one per combustion event. A diesel smell comes from the engine bay, and through the ventilation into the cabin as well. Black, oily deposits are visible at the base of the injector. The engine oil becomes diluted with fuel, and whitish-blue smoke can appear too.

If things are taken past this point, the carbon literally welds the injector into place, and a dedicated injector puller or a slide hammer is needed to get it out. Prying damages the body of the injector. If the seat has already been eaten away, the cylinder head has to be machined or replaced.

The quality of the repair decides matters here. A new copper washer is needed, the old one can never be reused, the seat has to be cleaned with a hand-turned seat cutter, and the torque has to follow the factory figure. Cleaning the seat is the most important step and the one most often done wrong. If one injector needs replacing, typically all four do, because their state of wear is similar, and a new one alongside worn ones does not give the right metering.

above 150,000 km

What to check

  • Listen at idle: a rhythmic chuffing noise means a leaking copper washer
  • Look at the base of the injectors: black, oily, hard deposits belong here
  • Smell the cabin and the engine bay: a diesel smell points to the same thing
3 more steps in the write-up

High pressure pump: metal debris throughout the whole system

expensive

The high pressure fuel pump wears from the inside, and metal dust forms in the friction pairs. The debris gets into the system and blocks everything there. The wear is reported above 160 000 kilometres, and the upper limit of the pump's life is around 200 000 kilometres, beyond which an overhaul is needed.

Show the rest

The metal dust travels on to the injectors and destroys those too, so a pump fault easily turns into a repair of the whole injection system: the system has to be flushed and the injectors replaced. The pump can also give up suddenly, even on a motorway, and the engine then stops while driving.

The injectors themselves also give up at around 200 000 kilometres, and their symptoms are easy to recognise. The most characteristic is difficult starting on a warm engine. With it comes damaged atomisation at the nozzle, a back-leak through the worn nozzle which makes starting worse still, and fuel getting into the crankcase and raising the oil level.

That last sign is the one that can be caught on the dipstick: if the oil has risen above MAX and smells of diesel, it belongs to the injection system.

above 160,000 km

What to check

  • Look at the oil on the dipstick: oil risen above MAX and smelling of diesel belongs to the injection system
  • Start it with a warm engine too: difficulty starting warm is the most characteristic symptom
  • Ask for the last fuel filter change and ask whether the filter was checked for metal debris
3 more steps in the write-up

Checklist

Ford Galaxy 2.0 TDCi 140hp Titanium

First what you would check on any car. Then the faults of this model.

Before you buy

Checklist

The printed sheet starts with what you would check on any car. What you tick stays on this device only.

On every car

Ask the owner

Faults of this model

vinkodex.com · Before you buy it, see what can go wrong.

Engine and transmission

4 engines · 2 transmissions

QXBA · 2.0 TDCI FLH

103 kW (140 HP) · diesel

M66 · 6-speed manual

manual · 6 speed

Torque limit450 Nm
MakerFord/Getrag

We built the code from the model and the gear count. The factory sheet does not state it. More than one engine code is possible. The fault list shows the faults of each. More than one transmission is possible. The gear count does not tell them apart. The code is on the side of the transmission.

Variant data

What is in this version

Factory data

Trim
Titanium
Body
MPV
Fuel
diesel
Transmission
manual
Engine size
1997 cc
Power
103 kW (140 HP)
Drive
FWD
Production
2010–2015

Factory service interval

The manufacturer specifies this for this version. Of the mileage and the time, the one that comes first is the one that counts.

  • Air filter

    • 60,000 km or 4 years

  • Cabin (pollen) filter

    • 30,000 km or 2 years

  • Brake fluid change

    • first: 3 years, then 2 years(first change at 3 years, then every two years)

  • Fuel filter, diesel

    • 60,000 km or 2 years
All Mk2.5 versions

Information, not an expert opinion

We write the descriptions, and we put the source next to them. A person reviews them before they go out. They are still information, not a technical expert opinion.

  • A fault on the list does not mean the car you are looking at has it.
  • A fault missing from the list does not mean the model is fault-free. Write-ups are made model by model. Not all of them are done.
  • You decide whether to buy. This is no substitute for an inspection. That needs a workshop and a history check.
Details in the terms