vinkodex.

Volkswagen Jetta 1.9 TDI 105hp Comfortline common faults.

2005–2011, saloon, diesel, 105 HP.

The fault list covers: BKC, BLS, BXE engine, DQ200, DQ250 transmission.

What you save stays on this device only. My saves

8 fault write-ups. 6 important. 3 recalls.

If you know the year, pick it. Faults for other years drop out of the list.

Before you buy

Known faults

6 important faults

critical1

PD TDI: the injector seat works loose, cylinder head damage

critical

The PD (pump injector) unit is held in the cylinder head by a single side bolt. Over time the seat works itself loose: the mounting slackens, the copper ring no longer seals, and hot combustion gas blows past. First you hear a characteristic "puffing", rhythmic blowing noise from the top of the engine when cold, soot appears under the cam cover, and then the seat surface in the cylinder head erodes. At that point replacing the seal is not enough: the head has to be refurbished or replaced. It affects PD engines between 1998 and 2010, regardless of size.

What to check

  • After a cold start open the bonnet and listen above the cam cover for a rhythmic blowing, "puffing" noise
  • Shine a light around the cam cover and the injectors: oily soot indicates blow-by
  • Ask whether a PD unit or a copper ring was replaced, and whether a compression test was done afterwards
1 more steps in the write-up

expensive5

DQ250 (6 speed wet DSG): mechatronics and clutch pack

expensive

The solenoids of the mechatronics unit wear out: slow or harsh shifting, then limp mode. A characteristic sign is the partial or complete loss of reverse. Wear of the clutch pack or the wrong spring force causes jerking and slipping. Because of the wet design it fails less often and at higher mileage than the dry DQ200, but when it does fail, it is expensive.

above 150,000 km

What to check

  • Pull away slowly from standstill and watch how smooth the 1 to 2 and 2 to 3 shifts are
  • Select reverse several times, cold and warm: is it delayed, does it engage at all
  • Under load (on a slope) watch whether the clutch slips
2 more steps in the write-up

DQ200 (7 speed dry DSG): mechatronics

expensive

A thin wall of the mechatronics valve body can crack, which causes a loss of pressure. The typical signs: jerking and harsh shifting from 1st to 2nd at low speed, a flashing PRNDS display, then a gear engagement fault, intermittently at first.

What to check

  • Pull away slowly from standstill and watch the 1 to 2 shift: does it jerk, is it harsh
  • Check whether the PRNDS display flashes or the dash reports a gearbox fault
  • In creep mode (brake released), does the car move off evenly
1 more steps in the write-up

Dual mass flywheel: diesel

expensive

The internal springs of the flywheel tire, and the two discs knock against each other. The signs are a rattling or knocking from the bellhousing at idle and when releasing the clutch pedal, and vibration through the floor. If the clutch slips without a burnt smell, that also points to the flywheel. It is worth replacing in time: a disintegrated flywheel can destroy the bellhousing too. At a clutch replacement the two go together anyway.

What to check

  • At idle, without touching the clutch pedal, listen for the rattle from the bellhousing, then press the pedal: if it stops, that is suspect
  • Watch for the characteristic clatter on starting and switching off
  • Put your foot on the floor at idle: a noticeable vibration indicates tired springs
2 more steps in the write-up

PD TDI: camshaft and rocker wear

expensive

The PD injectors (on the 1.4, 1.9 and 2.0 TDI alike) are driven by the camshaft itself, against more than 2,000 bar. That wears the lobes and the rockers quickly: first a knocking noise, then a rough idle, hard starting and loss of power. The cause is the wrong oil: the PD engine requires a 5W-40 lubricant to the VW 505.01 specification, with PD approval. A plain synthetic is not enough, and on an everyday 5W-30 the lobes can wear through.

What to check

  • Listen for knocking from the cam cover when cold: that is the first sign
  • Ask for the service book and check what oil was used (VW 505.01)
  • Watch how even the idle is, and whether it starts hard when cold
2 more steps in the write-up

TDI: the vanes of the variable geometry (VNT) turbo stick

expensive

The vanes of the variable geometry turbo are glued together by soot and oil arriving through the EGR. First you get overboost or a lack of boost, then loss of power above 2,000 rpm, and finally limp mode. Caught in time it is enough to remove the turbo, clean it and fit a new actuator rod. Short urban trips and gentle, low rev driving speed up the deposits.

What to check

  • On the motorway, load it above 2,000 rpm: does it pull evenly, or does the power break up
  • Watch whether the warning light flashes up under acceleration (overboost protection)
  • Ask what kind of journeys it did: a daily short urban run is the worst
1 more steps in the write-up

cheap repair2

DSG selector lever: failure of the P position switch

cheap repair

The dash shows "Error: Workshop! Only leave vehicle in position P" with an audible warning. The message appears in whatever language the car is set to, for example "Fehler: Werkstatt! Fahrzeug nur in Stellung P verlassen" in German.

Show the rest

The message points at the gearbox, but the fault is not there. A tiny switch sits in the module under the selector lever and signals that the lever is in park (P). Its contact wears and can also burn. That makes the signal unreliable, and the car warns you. The fault codes appear as 617752, P173400 or B116229.

At first it is intermittent. Sometimes the message comes up, sometimes not, so a short test drive easily misses it. Later it becomes permanent, and the gearbox can drop into limp mode.

This fault looks more expensive than it is. The maker released a separate retrofit switch kit for it (5Q0713128A for the black module, 3Q0713128 for the white one), which can be fitted in half an hour. The kit costs 70 to 100 pounds. At a franchised dealer, however, the whole selector lever module sometimes gets replaced, which costs 626 to 1,000 pounds there. So the difference between the two routes is roughly tenfold.

The affected group is post 2013 MQB platform Volkswagen, Audi, Seat and Skoda cars with a DSG gearbox. The switch is in these gearboxes, because that is what these cars have in common. The part itself is not part of the gearbox but of the module under the lever.

What to check

  • Watch the dash after starting: the message is intermittent and can be missed on a short loop
  • Move the lever from P to D and back several times, then get out and lock the car
  • Ask whether the selector lever switch has been replaced already, and ask for the invoice
2 more steps in the write-up

G28 crankshaft speed sensor dropping out

cheap repair

The G28 sensor drops out as it heats up. While driving the car stops, then starts again after a few minutes. When warm it starts with difficulty or not at all, while cold it starts, so the workshop often cannot reproduce it. The fault code does not always stay stored either.

What to check

  • Ask specifically: has it ever stopped while driving, and did it start again afterwards
  • Run it up to temperature, switch it off for 10 minutes, then restart: long cranking is suspect
  • With a code reader look for the stored (not just the active) engine control faults
1 more steps in the write-up

Checklist

Volkswagen Jetta 1.9 TDI 105hp Comfortline

First what you would check on any car. Then the faults of this model.

Before you buy

Checklist

The printed sheet starts with what you would check on any car. What you tick stays on this device only.

On every car

Ask the owner

Faults of this model

vinkodex.com · Before you buy it, see what can go wrong.

Official recall3 recallsShow

The manufacturer fixes these for free at a franchised dealer. Ask with the VIN whether it was done.

Most recent: 10 December 2010

10V621000FUEL SYSTEM, GASOLINE:DELIVERY:HOSES, LINES/PIPING, AND FITTINGSFUEL SYSTEM, GASOLINE:DELIVERY:HOSES, LINES/PIPING, AND FITTINGS10 December 2010 · NHTSA (USA)

VOLKSWAGEN IS RECALLING CERTAIN MODEL YEAR 2006-2010 JETTA, NEW BEETLE, NEW BEETLE CONVERTIBLE, MODEL YEAR 2009 JETTA SPORTWAGEN AND MODEL YEAR 2007-2009 RABBIT VEHICLES EQUIPPED WITH 2.5L ENGINES. THE JETTA, JETTA SPORTWAGEN, AND RABBIT VEHICLES MAY HAVE A SMALL PLASTIC TAB LOCATED ON THE WINDSHIELD WASHER FLUID RESERVOIR THAT MAY CHAFE AGAINST AN UNDERHOOD FUEL SUPPLY LINE. THE NEW BEETLE AND THE NEW BEETLE CONVERTIBLE VEHICLES MAY HAVE A FASTENING CLAMP ON A HYDRAULIC HOSE OF THE POWER STEERING SYSTEM THAT MAY BE LOCATED IN AN IMPROPER POSITION WHICH COULD CAUSE CHAFING AGAINST AN UNDERHOOD FUEL SUPPLY LINE.

Risk: IF CHAFING OCCURS, THERE IS THE POTENTIAL FOR A FUEL LEAK TO DEVELOP. FUEL LEAKAGE, IN THE PRESENCE OF AN IGNITION SOURCE, COULD RESULT IN A FIRE.

Remedy: DEALERS WILL INSPECT AND IF NECESSARY REPLACE THE UNDERHOOD FUEL LINE. ADDITIONALLY, DEPENDING ON THE VEHICLE MODEL, DEALERS WILL EITHER REMOVE THE PLASTIC TAB FROM THE WINDSHIELD WASHER FLUID RESERVOIR, OR INSPECT THE POSITION OF THE FASTENING CLAMP AND ADJUST THE RELATED FASTENING CLAMP INTO THE CORRECT POSITION. THIS SERVICE WILL BE PERFORMED FREE OF CHARGE. THE SAFETY RECALL IS EXPECTED TO BEGIN ON OR BEFORE JANUARY 31, 2011. OWNERS MAY CONTACT VOLKSWAGEN AT 1-800-822-8987.

The authority's notice

09V164000POWER TRAIN:DRIVELINE:DRIVESHAFTPOWER TRAIN:DRIVELINE:DRIVESHAFT19 May 2009 · NHTSA (USA)

VOLKSWAGEN IS RECALLING 25,594 MY 2006-2009 JETTA 5TH GENERATION EQUIPPED WITH 2.01 ENGINE. THE FASTENING SCREW CONTACT SURFACES ON THE DRIVESHAFT COVER PLATE MAY NOT HAVE BEEN MANUFACTURED TO FACTORY SPECIFICATIONS. SOME SCREWS MAY NOT HAVE BEEN TORQUED PROPERLY DURING ASSEMBLY AND COULD LOOSEN OVER TIME, CAUSING A KNOCKING SOUND WHEN THE VEHICLE IS IN MOTION. THE DRIVESHAFT SCREWS COULD LOOSEN TO THE POINT WHERE THE DRIVESHAFT DETACHES FROM THE GEARBOX.

Risk: IF THE VEHICLE IS MOVING WHEN THIS HAPPENS, THE DETACHED DRIVESHAFT COULD CAUSE DAMAGE THE GEARBOX HOUSING. A DAMAGE GEARBOX HOUSING COULD LEAK GEARBOX OIL ONTO THE STREET AND CREATE A RISK OF A VEHICLE CRASH FOR BOTH THE DRIVER AND OTHER MOTORISTS.

Remedy: DEALERS WILL INSPECT THE DRIVESHAFT SCREWS AND REPLACE THE SCREWS FREE OF CHARGE. THE RECALL BEGAN ON JUNE 24, 2009. OWNERS MAY CONTACT VOLKSWAGEN AT 1-800-822-8987.

The authority's notice

07V442000EXTERIOR LIGHTING:HEADLIGHTSEXTERIOR LIGHTING:HEADLIGHTS24 September 2007 · NHTSA (USA)

CERTAIN VEHICLES FAIL TO COMPLY WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 108, "LAMPS, REFLECTIVE DEVICES, AND ASSOCIATED EQUIPMENT." SOME VEHICLES MAY NOT HAVE HAD A REQUIRED CAP INSTALLED WHICH DISABLES THE HEADLIGHT HORIZONTAL AIM AND SOME VEHICLES MAY CONTAIN A CAP THAT DISABLES THE VERTICAL AIMING SCREW.

Risk: NONCOMPLIANCE CAN INHIBIT PROPER HEADLAMP AIM ADJUSTMENT FOR ROADWAY ILLUMINATION, IMPROPERLY AIMED HEADLAMPS COULD CAUSE REDUCED ROAD VISIBILITY, INCREASING THE RISK OF A CRASH.

Remedy: DEALERS WILL INSPECT FOR THE PRESENCE OF A CAP IN THE SOCKET OF THE LOW BEAM HORIZONTAL AIMING SCREW AND INSTALL ONE IF MISSING, AND INSPECT FOR THE PRESENCE OF A CAP IN THE SOCKET OF THE VERTICAL AIMING SCREW AND IF PRESENT, THE CAP WILL BE REMOVED. THE RECALL WILL BEGIN ON OCTOBER 31, 2007. OWNERS MAY CONTACT VW AT 1-800-822-8987.

The authority's notice

Engine and transmission

3 engines · 2 transmissions

BKC · 1.9 TDI

77 kW (105 HP) · diesel

DQ200 · 7-speed DSG, dry clutch

DSG · 7 speed

Clutchdry
Torque limit250 Nm
MakerVolkswagen

We built the code from the model and the gear count. The factory sheet does not state it. More than one engine code is possible. The fault list shows the faults of each. More than one transmission is possible. 6 gears = DQ250, 7 gears = DQ200.

Variant data

What is in this version

Factory data

Trim
Comfortline
Body
saloon
Fuel
diesel
Transmission
automatic
Engine size
1896 cc
Power
77 kW (105 HP)
Drive
FWD
Production
2005–2011

Factory service interval

The manufacturer specifies this for this version. Of the mileage and the time, the one that comes first is the one that counts.

  • Air filter

    • 60,000 km or 4 years

  • DQ200: lifetime fill by the maker, not in practice

    • lifetime fill: the maker does NOT specify a change

  • Cabin (pollen) filter

    • 30,000 km or 2 years

  • Engine oil and oil filter

    • LongLife30,000 km or 2 years(valid only with LongLife-approved oil)
    • 15,000 km or 1 year

  • Brake fluid change

    • first: 3 years, then 2 years(first change at 3 years, then every two years)

  • Timing belt, 1.9 PD TDI

    • 130,000 km or 5 years(60,000 or 80,000 miles depending on the build year)

  • Coolant (antifreeze) change

    • first: 193,000 km or 10 years, then 97,000 km or 5 years(G13 / G12++: first change at 120,000 miles or 10 years, then every 60,000 miles or 5 years)

  • Fuel filter, diesel

    • 60,000 km or 2 years
All V versions

Information, not an expert opinion

We write the descriptions, and we put the source next to them. A person reviews them before they go out. They are still information, not a technical expert opinion.

  • A fault on the list does not mean the car you are looking at has it.
  • A fault missing from the list does not mean the model is fault-free. Write-ups are made model by model. Not all of them are done.
  • You decide whether to buy. This is no substitute for an inspection. That needs a workshop and a history check.
Details in the terms