vinkodex.

Volkswagen Jetta 2.0 TDI Highline common faults.

2011–2014, saloon, diesel, 140 HP.

The fault list covers: CFFB, CLCB engine, DQ250 transmission.

What you save stays on this device only. My saves

7 fault write-ups. 6 important. 18 recalls.

If you know the year, pick it. Faults for other years drop out of the list.

Before you buy

Known faults

6 important faults

critical2

The EGR cooler cools the recirculated exhaust gas before it enters the intake again, and coolant flows through it while it does so. The temperature difference between the two sides is large, so the wall can crack or the gasket can let through, and then the coolant reaches the exhaust or the intake side. This leaves no puddle under the car and the place of the leak is not visible from outside: the coolant evaporates and the level drops slowly, over weeks. The accompanying signs are whitish smoke, a rising coolant temperature, raised pressure in the cooling system and a sweetish smell. If it goes on for months the cylinder head can be damaged too, because the cooling gradually gets worse. On the EA189 engines the fault code P2425 usually comes with it. The problem is reported above 100,000 km, and replacing the cooler costs 600 to 1,500 euro.

above 100,000 km600–1,500 EUR

What to check

  • Look at the level in the expansion tank and ask how much has to be topped up
  • Look for traces outside: if the level drops but there is no puddle or streak, the leak is internal
  • After a cold start watch the exhaust, because lasting whitish smoke is not only condensation
2 more steps in the write-up

The balance shaft module drives the oil pump through a hexagonal shaft stub. That hex and its mating part gradually round off, until the shaft finally turns freely: the oil pump stops and the oil pressure is gone. The process gives no warning, and that is exactly what makes it dangerous. The failure typically happens at high revs, and the oil pressure light comes on only once the damage is already done. The factory hex is undersized, so it knocks against the wall of the bore, and the wear accelerates itself. The maker classed it as a "tolerance deviation" and, given the small number of cases against total production, did not recommend preventive repair; Audi alone ran a service action (13D7). The replacement is expensive: on the German market the module replacement is 1,300 to 1,700 euro, and an independent repair touching only the hex is around 650 euro. The reported cases cluster around the Passat B6, Sharan, Audi A4/A6, Superb and Alhambra, in model years between 2005 and 2009. This layout is not only on the pump-injector (PD) engines, it is on the common rail EA189 engines too: the same module, the same hex, the same wear. The failure is typically reported between 100,000 and 160,000 km. The first sign is a short flash of the oil pressure light, in a long bend or a few seconds after a cold start, and then quiet again. The versions without balance shafts (BKD, BMM, BMN, AZV) drive the oil pump differently and are not affected by this wear. If the light stays on or flashes, stop as soon as it is safe, switch the engine off, and do not restart it until the oil pressure has been measured.

between 100,000 and 160,000 km

What to check

  • Ask whether the balance shaft module or the oil pump drive has been replaced, and if so, with a factory or a strengthened hex
  • Read through the service book: has an oil pressure warning ever flashed, even once
  • Unscrew the oil filler cap and look for metallic glitter in the lubricant
3 more steps in the write-up

expensive4

The EGR valve and its cooler block up with soot and oily deposits; the particulate filter cannot regenerate on short urban trips. The signs are reduced power, a warning light, and frequent regeneration. The software update after the diesel emissions affair made the EGR operate more often, which accelerated the phenomenon: the maker gave goodwill repairs in several cases.

between 140,000 and 160,000 km

What to check

  • Ask what kind of journeys the car did: a daily short urban run is the worst for the filter
  • With a code reader look at the stored faults (P0401/P0402, and P2002 for the filter)
  • Ask whether it received the post emissions affair software update, and when
1 more steps in the write-up

The solenoids of the mechatronics unit wear out: slow or harsh shifting, then limp mode. A characteristic sign is the partial or complete loss of reverse. Wear of the clutch pack or the wrong spring force causes jerking and slipping. Because of the wet design it fails less often and at higher mileage than the dry DQ200, but when it does fail, it is expensive.

above 150,000 km

What to check

  • Pull away slowly from standstill and watch how smooth the 1 to 2 and 2 to 3 shifts are
  • Select reverse several times, cold and warm: is it delayed, does it engage at all
  • Under load (on a slope) watch whether the clutch slips
2 more steps in the write-up

The internal springs of the flywheel tire, and the two discs knock against each other. The signs are a rattling or knocking from the bellhousing at idle and when releasing the clutch pedal, and vibration through the floor. If the clutch slips without a burnt smell, that also points to the flywheel. It is worth replacing in time: a disintegrated flywheel can destroy the bellhousing too. At a clutch replacement the two go together anyway.

What to check

  • At idle, without touching the clutch pedal, listen for the rattle from the bellhousing, then press the pedal: if it stops, that is suspect
  • Watch for the characteristic clatter on starting and switching off
  • Put your foot on the floor at idle: a noticeable vibration indicates tired springs
2 more steps in the write-up

The vanes of the variable geometry turbo are glued together by soot and oil arriving through the EGR. First you get overboost or a lack of boost, then loss of power above 2,000 rpm, and finally limp mode. Caught in time it is enough to remove the turbo, clean it and fit a new actuator rod. Short urban trips and gentle, low rev driving speed up the deposits.

What to check

  • On the motorway, load it above 2,000 rpm: does it pull evenly, or does the power break up
  • Watch whether the warning light flashes up under acceleration (overboost protection)
  • Ask what kind of journeys it did: a daily short urban run is the worst
1 more steps in the write-up

cheap repair1

The dash shows "Error: Workshop! Only leave vehicle in position P" with an audible warning. The message appears in whatever language the car is set to, for example "Fehler: Werkstatt! Fahrzeug nur in Stellung P verlassen" in German.

Show the rest

The message points at the gearbox, but the fault is not there. A tiny switch sits in the module under the selector lever and signals that the lever is in park (P). Its contact wears and can also burn. That makes the signal unreliable, and the car warns you. The fault codes appear as 617752, P173400 or B116229.

At first it is intermittent. Sometimes the message comes up, sometimes not, so a short test drive easily misses it. Later it becomes permanent, and the gearbox can drop into limp mode.

This fault looks more expensive than it is. The maker released a separate retrofit switch kit for it (5Q0713128A for the black module, 3Q0713128 for the white one), which can be fitted in half an hour. The kit costs 70 to 100 pounds. At a franchised dealer, however, the whole selector lever module sometimes gets replaced, which costs 626 to 1,000 pounds there. So the difference between the two routes is roughly tenfold.

The affected group is post 2013 MQB platform Volkswagen, Audi, Seat and Skoda cars with a DSG gearbox. The switch is in these gearboxes, because that is what these cars have in common. The part itself is not part of the gearbox but of the module under the lever.

What to check

  • Watch the dash after starting: the message is intermittent and can be missed on a short loop
  • Move the lever from P to D and back several times, then get out and lock the car
  • Ask whether the selector lever switch has been replaced already, and ask for the invoice
2 more steps in the write-up

Checklist

Volkswagen Jetta 2.0 TDI Highline

First what you would check on any car. Then the faults of this model.

Before you buy

Checklist

The printed sheet starts with what you would check on any car. What you tick stays on this device only.

On every car

Ask the owner

vinkodex.com · Before you buy it, see what can go wrong.

Official recall18 recallsShow

The manufacturer fixes these for free at a franchised dealer. Ask with the VIN whether it was done.

Most recent: 21 October 2020

20V648000FUEL SYSTEM, GASOLINE:FUEL INJECTION SYSTEM:FUEL RAILFUEL SYSTEM, GASOLINE:FUEL INJECTION SYSTEM:FUEL RAIL21 October 2020 · NHTSA (USA)

Volkswagen Group of America, Inc. (Volkswagen) is recalling certain 2016-2018 Jetta vehicles. The fuel rail bolts may become loose over time, allowing fuel to leak.

Risk: A fuel leak increases the risk of a fire.

Remedy: Volkswagen will notify owners, and dealers will replace the fuel rail bolts and, as necessary, the fuel rail. The recall began March 31, 2021. Owners may contact Volkswagen customer service at 1-800-893-5298. Volkswagen's number for this recall is 24Gi.

We could not check this: model year. The authority's notice

19V615000ELECTRICAL SYSTEM:IGNITION:ANTI-THEFT:CONTROL MODULEELECTRICAL SYSTEM:IGNITION:ANTI-THEFT:CONTROL MODULE22 August 2019 · NHTSA (USA)

Volkswagen Group of America, Inc. (Volkswagen) is recalling certain 2015-2019 GTI, 2015-2016 and 2018-2019 Golf, 2012-2019 Beetle and Beetle Convertible, 2017-2019 Golf SportWagen and 2011-2018 Jetta vehicles equipped with an automatic transmission, manual handbrake and keyless entry. A build-up of silicate on the shift lever micro switch contacts may enable the key to be removed from the ignition when the transmission shift lever is not in "Park."

Risk: Removing the key while the shift lever is in a position other than "Park" increases the risk of an unintended vehicle rollaway that may result in personal injury or a crash.

Remedy: Volkswagen will notify owners, and dealers will install an additional switch and circuit board, free of charge. The recall began November 19, 2019. Owners may contact Volkswagen customer service at 1-800-893-5298. Volkswagen's number for this recall is 37M2.

We could not check this: model year. The authority's notice

INFO/00145/21Safety recallInjuries13 May 2019 · EU Safety Gate

Defective material may be used in the rear suspension helical springs. As a result, the springs could break, impairing the driving stability and increasing the risk of an accident. The product does not comply with the requirements laid down in the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles

Remedy: Type of economic operator taking notified measure(s): Importer Category of measure(s): Recall of the product from end users Date of entry into force: 13/05/2019

We could not check this: model year. The authority's notice

17V352000EQUIPMENT:OTHER:LABELSEQUIPMENT:OTHER:LABELS31 May 2017 · NHTSA (USA)

Volkswagen Group of America, Inc. (Volkswagen) is recalling certain 2017 Jetta vehicles. The affected vehicles have Vehicle Identification Number (VIN) markings on the body that do not match the VIN plate near the windshield. As such, these vehicles fail to comply with the requirements of 49 CFR Part 567, "Certification."

Risk: The mismatched VINs make the vehicle noncompliant with regulatory requirements.

Remedy: Volkswagen has notified owners and has replaced the vehicles, free of charge. The recall began on July 7, 2017. Owners may contact Volkswagen customer service at 1-800-893-5298. Volkswagen's number for this recall is 06A8.

We could not check this: model year. The authority's notice

17V136000EQUIPMENT:OTHER:LABELSEQUIPMENT:OTHER:LABELS2 March 2017 · NHTSA (USA)

Volkswagen Group of America, Inc. (Volkswagen) is recalling certain 2017 Beetle and Jetta GLI vehicles. The affected vehicles have incorrect information on the tire information label, possibly causing the operator to overload the vehicle. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 110, "Tire Selection and Rims."

Risk: Overloading the vehicle may affect vehicle handling or result in tire damage, increasing the risk of a crash.

Remedy: Volkswagen will notify owners, and dealers will install a corrected tire information label, free of charge. The recall began March 30, 2017. Owners may contact Volkswagen customer service at 1-800-893-5298. Volkswagen's number for the recall is 01B9.

We could not check this: model year. The authority's notice

17V137000EQUIPMENT:OTHER:LABELSEQUIPMENT:OTHER:LABELS2 March 2017 · NHTSA (USA)

Volkswagen Group of America, Inc. (Volkswagen) is recalling certain 2017 Jetta vehicles. The affected vehicles have incorrect information on the tire information label, possibly causing the operator to overload the vehicle. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 110, "Tire Selection and Rims."

Risk: Overloading the vehicle may affect vehicle handling or result in tire damage, increasing the risk of a crash.

Remedy: Volkswagen will notify owners, and dealers install a corrected tire information label, free of charge. The recall began March 30, 2017. Owners may contact Volkswagen customer service at 1-800-893-5298. Volkswagen's number for the recall is 01B8

We could not check this: model year. The authority's notice

17V070000ENGINE AND ENGINE COOLING:ENGINEENGINE AND ENGINE COOLING:ENGINE3 February 2017 · NHTSA (USA)

Volkswagen Group of America, Inc. (Volkswagen) is recalling certain 2017 Jetta vehicles equipped with a 1.4L engine. These vehicles have an engine that may seize due to an improper casting of the block.

Risk: If the engine seizes, the wheels may suddenly lock up, causing a loss of vehicle control and increasing the risk of a crash.

Remedy: Volkswagen will either buy back the vehicle or replace the engine block, free of charge. The recall began February 2017. Owners may contact Volkswagen customer service at 1-800-893-5298. Volkswagen's number for this recall is 10F4.

We could not check this: model year. The authority's notice

16V913000SERVICE BRAKES, HYDRAULIC:ANTILOCK/TRACTION CONTROL/ELECTRONIC LIMITED SLIPSERVICE BRAKES, HYDRAULIC:ANTILOCK/TRACTION CONTROL/ELECTRONIC LIMITED SLIP20 December 2016 · NHTSA (USA)

Volkswagen Group of America, Inc. (Volkswagen) is recalling certain model year 2009-2010 Volkswagen Jetta A5 Sedan, 2009 Volkswagen Jetta SportWagen, Eos, GTI, Rabbit and Audi A3 vehicles, and 2010 Volkswagen Golf A6 vehicles. The Antilock Brake System (ABS) control unit may fail during ABS or Electronic Stability Control (ESC) activation, possibly causing a loss of vehicle control.

Risk: A loss of vehicle control can increase the risk of a crash.

Remedy: Volkswagen will notify owners, and dealers will update the ABS control module software to improve the module's self-testing abilities. Any module that fails the new diagnostic test will be replaced. These repairs will be made free of charge. The recall began February 2017. Owners may contact Volkswagen customer service at 1-800-893-5298.

We could not check this: model year. The authority's notice

15V627000AIR BAGS:FRONTAL:SENSOR/CONTROL MODULE-INACTIVEAIR BAGS:FRONTAL:SENSOR/CONTROL MODULE-INACTIVE7 October 2015 · NHTSA (USA)

Volkswagen Group of America, Inc. (Volkswagen) is recalling certain model year 2015 Jetta vehicles manufactured September 8, 2014, to November 28, 2014, Golf vehicles manufactured April 2, 2014, to December 3, 2014, and E-Golf vehicles manufactured July 26, 2014, to October 18, 2014. The affected vehicles are equipped a Passenger Occupant Detection System (PODS) that may have been manufactured improperly. As a result, the front passenger seat occupant may be improperly classified or may not be detected.

Risk: In the event of a crash, if the front passenger seat occupant is incorrectly classified or non-detected, the passenger frontal air bag may deploy improperly or not at all, increasing the risk of occupant injury.

Remedy: Volkswagen will notify owners, and dealers will replace the PODS control module, free of charge. The recall began on November 20, 2015. Owners may contact Volkswagen customer service at 1-800-893-5298. Volkswgen's number for this recall is 69L6.

We could not check this: model year. The authority's notice

14V790000EXTERIOR LIGHTING:HEADLIGHTSEXTERIOR LIGHTING:HEADLIGHTS15 December 2014 · NHTSA (USA)

Volkswagen Group of America, Inc. (Volkswagen) is recalling certain model year 2015 Jetta vehicles manufactured July 11, 2014, to November 13, 2014. Due to incorrect software within the headlight control module, the low beam headlights may turn off when high beam lights are turned on. As a result, the light output from the headlights may be insufficient. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) No. 108. "Lamps, Reflective Devices, and Associated Equipment."

Risk: Insufficient headlight output may increase the risk of a crash.

Remedy: Volkswagen will notify owners, and dealers will update the headlight control module software, free of charge. The recall is expected to begin in January 2015. Owners may contact Volkswagen customer service at 1-800-893-5298. Volkswagen's number for this recall is 57F6.

We could not check this: model year. The authority's notice

14V656000SUSPENSION:REARSUSPENSION:REAR20 October 2014 · NHTSA (USA)

Volkswagen Group of America, Inc. (Volkswagen) is recalling certain model year 2011-2013 Jetta vehicles manufactured March 1, 2010, to November 30, 2012, and 2012-2013 Beetle vehicles manufactured March 1, 2011, to July 31, 2013. The durability of the rear trailing arms may be reduced in vehicles whose rear trailing arms have been previously deformed, such as a result of a rear or side-rear impact crash.

Risk: The reduced durability of the trailing arm may result in its sudden fracture, possibly causing loss of vehicle control and increasing the risk of a crash.

Remedy: Volkswagen will notify owners, and dealers will install a sheet metal inlay on the rear axle trailing arms designed to prevent a sudden loss of control in the event of trailing arm sudden fracture, free of charge. The recall began April 7, 2015. Owners may contact Volkswagen customer service at 1-800-893-5298.

We could not check this: model year. The authority's notice

11V490000FUEL SYSTEM, DIESELFUEL SYSTEM, DIESEL3 October 2011 · NHTSA (USA)

VOLKSWAGEN IS RECALLING CERTAIN MODEL 2009-2012 JETTA AND JETTA SPORTWAGEN VEHICLES, MANUFACTURED FROM MAY 2008 THROUGH SEPTEMBER 2011, MODEL YEAR 2010-2012 VOLKSWAGEN GOLF VEHICLES, MANUFACTURED FROM MAY 2009 THROUGH SEPTEMBER 2011, AND MODEL YEAR 2010-2012 AUDI A3 VEHICLES, MANUFACTURED FROM SEPTEMBER 2009 THROUGH SEPTEMBER 2011, THAT ARE EQUIPPED WITH A 2.0L TDI COMMON RAIL DIESEL ENGINE/CLEAN DIESEL ENGINE. THE FUEL INJECTION PULSES COULD COINCIDE WITH THE NATURAL FREQUENCY OF THE INJECTOR LINE #2, IN SPECIFIC LOAD AND RPM CONDITIONS. THIS RESONANCE CREATES ADDITIONAL STRESS IN THE FUEL LINE.

Risk: DUE TO THE RESONANCE CONDITION, INJECTOR LINE NUMBER 2 COULD DEVELOP SMALL CRACKS WHICH COULD LEAD TO FUEL LEAKAGE. LEAKING FUEL IN THE PRESENCE OF AN IGNITION SOURCE, MAY LEAD TO A FIRE.

Remedy: VOLKSWAGEN WILL INSTALL AN IMPROVED FUEL INJECTOR LINE FOR THE NUMBER 2 CYLINDER ON CERTAIN VEHICLES AND WILL INSTALL VIBRATION DAMPERS ON ALL OF THE INJECTOR LINES. VOLKSWAGEN AND AUDI WILL NOTIFY OWNERS TO HAVE THE VEHICLES REPAIRED FREE OF CHARGE. THE SAFETY RECALL IS EXPECTED TO BEGIN DURING NOVEMBER 2011. OWNERS MAY CONTACT VOLKSWAGEN AT 1-800-822-8987.

We could not check this: model year. The authority's notice

11V466000ENGINE AND ENGINE COOLING:EXHAUST SYSTEMENGINE AND ENGINE COOLING:EXHAUST SYSTEM7 September 2011 · NHTSA (USA)

VOLKSWAGEN IS RECALLING CERTAIN MODEL YEAR 2011-2012 JETTA SEDAN VEHICLES MANUFACTURED FROM MARCH 18, 2010, THROUGH AUGUST 22, 2011. SOME VEHICLES HAD A STAINLESS STEEL EXHAUST TIP INSTALLED AT THE PORT DURING IMPORTATION. THESE EXHAUST TIPS MAY EXTEND BEYOND THE ORIGINAL LENGTH OF THE FACTORY-INSTALLED EXHAUST PIPES. IT IS POSSIBLE FOR INADVERTENT CONTACT TO OCCUR WITH A PERSON'S LEG.

Risk: IF THE TAILPIPE EXTENSION IS HOT DURING INADVERTENT CONTACT, A BURN COULD OCCUR.

Remedy: DEALERS WILL INSPECT AND REPLACE THE STAINLESS STEEL EXHAUST TIPS AS NECESSARY FREE OF CHARGE. THE SAFETY RECALL IS EXPECTED TO BEGIN DURING NOVEMBER 2011. OWNERS MAY CONTACT VOLKSWAGEN AT 1-800-822-8987.

We could not check this: model year. The authority's notice

11V196000ELECTRICAL SYSTEM:WIRING:FUSES AND CIRCUIT BREAKERSELECTRICAL SYSTEM:WIRING:FUSES AND CIRCUIT BREAKERS29 March 2011 · NHTSA (USA)

VOLKSWAGEN IS RECALLING CERTAIN MODEL YEAR 2011 JETTA VEHICLES, MANUFACTURED FROM MARCH 2010 THROUGH MARCH 2011. THESE VEHICLES MAY HAVE AN ELECTRICAL WIRING AND FUSE LAYOUT WHERE THE CONVERTER BOX IS PROTECTED BY THE SAME FUSE USED BY THE SIGNAL HORN AND THE ANTI-THEFT ALARM SYSTEM. SHOULD THAT FUSE BE BLOWN, THE CONVERTER BOX WILL BE DISCONNECTED FROM THE POWER SUPPLY WHICH, IN TURN, WILL SHUT OFF APPLICATIONS SUCH AS THE ENGINE MANAGEMENT SYSTEM, LIGHTING SYSTEM, AND WIPERS.

Risk: SHOULD THIS HAPPEN WHILE THE VEHICLE IS BEING DRIVEN, THE ENGINE COULD STALL, OR THE HEADLIGHTS OR WIPERS COULD TURN OFF UNEXPECTEDLY, POTENTIALLY LEADING TO A CRASH WITHOUT WARNING.

Remedy: VOLKSWAGEN WILL NOTIFY OWNERS WHEN SUFFICIENT QUANTITIES OF REPAIRS KITS ARE AVAILABLE. DEALERS WILL SEPARATE THE WIRING FOR THE HORN AND THE THEFT PROTECTION HORN FROM THE POWER SUPPLY OF THE CONVERTER BOX AND ROUTE THE WIRES TO SEPARATE FUSES TO CORRECT THE CONDITION FREE OF CHARGE. THE SAFETY RECALL IS EXPECTED TO BEGIN DURING APRIL 2011. OWNERS MAY CONTACT VOLKSWAGEN AT 1-800-822-8987.

We could not check this: model year. The authority's notice

10V621000FUEL SYSTEM, GASOLINE:DELIVERY:HOSES, LINES/PIPING, AND FITTINGSFUEL SYSTEM, GASOLINE:DELIVERY:HOSES, LINES/PIPING, AND FITTINGS10 December 2010 · NHTSA (USA)

VOLKSWAGEN IS RECALLING CERTAIN MODEL YEAR 2006-2010 JETTA, NEW BEETLE, NEW BEETLE CONVERTIBLE, MODEL YEAR 2009 JETTA SPORTWAGEN AND MODEL YEAR 2007-2009 RABBIT VEHICLES EQUIPPED WITH 2.5L ENGINES. THE JETTA, JETTA SPORTWAGEN, AND RABBIT VEHICLES MAY HAVE A SMALL PLASTIC TAB LOCATED ON THE WINDSHIELD WASHER FLUID RESERVOIR THAT MAY CHAFE AGAINST AN UNDERHOOD FUEL SUPPLY LINE. THE NEW BEETLE AND THE NEW BEETLE CONVERTIBLE VEHICLES MAY HAVE A FASTENING CLAMP ON A HYDRAULIC HOSE OF THE POWER STEERING SYSTEM THAT MAY BE LOCATED IN AN IMPROPER POSITION WHICH COULD CAUSE CHAFING AGAINST AN UNDERHOOD FUEL SUPPLY LINE.

Risk: IF CHAFING OCCURS, THERE IS THE POTENTIAL FOR A FUEL LEAK TO DEVELOP. FUEL LEAKAGE, IN THE PRESENCE OF AN IGNITION SOURCE, COULD RESULT IN A FIRE.

Remedy: DEALERS WILL INSPECT AND IF NECESSARY REPLACE THE UNDERHOOD FUEL LINE. ADDITIONALLY, DEPENDING ON THE VEHICLE MODEL, DEALERS WILL EITHER REMOVE THE PLASTIC TAB FROM THE WINDSHIELD WASHER FLUID RESERVOIR, OR INSPECT THE POSITION OF THE FASTENING CLAMP AND ADJUST THE RELATED FASTENING CLAMP INTO THE CORRECT POSITION. THIS SERVICE WILL BE PERFORMED FREE OF CHARGE. THE SAFETY RECALL IS EXPECTED TO BEGIN ON OR BEFORE JANUARY 31, 2011. OWNERS MAY CONTACT VOLKSWAGEN AT 1-800-822-8987.

We could not check this: model year. The authority's notice

09V333000POWER TRAIN:AUTOMATIC TRANSMISSIONPOWER TRAIN:AUTOMATIC TRANSMISSION20 August 2009 · NHTSA (USA)

VOLKSWAGEN IS RECALLING CERTAIN MODEL YEAR 2009 AND 2010 PASSENGER CARS MANUFACTURED BETWEEN SEPTEMBER 2008 AND AUGUST 2009. THE WIRING HARNESS OF A TEMPERATURE SENSOR IN THE DIRECT SHIFT GEARBOX (DSG) MAY HAVE CONNECTOR WIRES THAT WERE INSUFFICIENTLY CRIMPED. WITH INSUFFICIENTLY CRIMPED CONNECTOR WIRES, A TEMPERATURE SENSOR HAS THE POTENTIAL TO FALSELY DETECT A HIGH GEARBOX OIL TEMPERATURE, CAUSING THE TRANSMISSION TO ABRUPTLY SHIFT TO NEUTRAL. IF THIS HAPPENS, THE SELECTOR LEVER POSITION INDICATOR WITHIN THE INSTRUMENT PANEL WILL FLASH. IN ADDITION, THE "DEPRESS BRAKE PEDAL" INDICATOR LIGHT WILL BE ILLUMINATED, ALERTING THE DRIVER TO APPLY THE BRAKES.

Risk: THE ABRUPT SHIFT TO NEUTRAL COULD LEAD TO A CRASH WITHOUT WARNING.

Remedy: VOLKSWAGEN WILL REPROGRAM THE TRANSMISSION CONTROL MODULE WITH UPDATED SOFTWARE FREE OF CHARGE. THE RECALL BEGAN ON OCTOBER 20, 2009. OWNERS MAY CONTACT VOLKSWAGEN AT 1-800-822-8987.

We could not check this: model year. The authority's notice

A12/00222/20Safety recallInjuriesno date · EU Safety Gate

Cars initially used for internal purposes of Volkswagen AG might not have been correctly modified before they were sold to the general public. There is a possibility that certain safety systems of these cars are not correctly modified for street use.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

We could not check this: model year. The authority's notice

A12/0909/17Safety recallInjuriesno date · EU Safety Gate

The earth connection of the ABS/ESP system may be interrupted as a result of thermomechanical overload. This would lead to the failure of the ABS/ESP system and the risk of an accident.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

We could not check this: model year. The authority's notice

Engine and transmission

2 engines · 1 transmissions

CFFB · 2.0 TDI

103 kW (140 HP) · diesel

DQ250 · 6-speed DSG, wet clutch

DSG · 6 speed

Clutchwet
Torque limit400 Nm
MakerVolkswagen

We built the code from the model and the gear count. The factory sheet does not state it. More than one engine code is possible. The fault list shows the faults of each.

Variant data

What is in this version

Factory data

Trim
Highline
Body
saloon
Fuel
diesel
Transmission
automatic
Engine size
1968 cc
Power
103 kW (140 HP)
Drive
FWD
Production
2011–2014

Factory service interval

The manufacturer specifies this for this version. Of the mileage and the time, the one that comes first is the one that counts.

  • Air filter

    • 60,000 km or 4 years
  • Cabin (pollen) filter

    • 30,000 km or 2 years
  • Engine oil and oil filter

    • LongLife30,000 km or 2 years(valid only with LongLife-approved oil)
    • 15,000 km or 1 year
  • Brake fluid change

    • first: 3 years, then 2 years(first change at 3 years, then every two years)
  • DSG oil change, WET clutch gearbox

    • 60,000 km or 4 years
  • Timing belt, 1.6 / 2.0 TDI (EA188/EA189/EA288)

    • 210,000 km(EA288, including the 1.6 TDI, with no time limit. 130,000 miles = 209,215 km. Parts maker repair specification, read by a human. The interval chart at https://www.rwcmotorsport.com/tech/tdi-maintenance.php gives the same figure independently.)
  • Coolant (antifreeze) change

    • first: 193,000 km or 10 years, then 97,000 km or 5 years(G13 / G12++: first change at 120,000 miles or 10 years, then every 60,000 miles or 5 years)
  • Fuel filter, diesel

    • 60,000 km or 2 years

Information, not an expert opinion

We write the descriptions, and we put the source next to them. A person reviews them before they go out. They are still information, not a technical expert opinion.

  • A fault on the list does not mean the car you are looking at has it.
  • A fault missing from the list does not mean the model is fault-free. Write-ups are made model by model. Not all of them are done.
  • You decide whether to buy. This is no substitute for an inspection. That needs a workshop and a history check.
Details in the terms