vinkodex.

BMW X2 X2 sDrive18d common faults.

2018–2023, SUV, diesel, 150 HP.

The fault list covers: B47C20U0 engine, GS6-UKL transmission.

What you save stays on this device only. My saves

4 fault write-ups. All are important. 11 recalls.

If you know the year, pick it. Faults for other years drop out of the list.

Before you buy

Known faults

4 important faults

The high pressure pump of these common rail diesels (Bosch CP4) can fail while driving. The characteristic course is not gradual: a "Drivetrain fault" message appears on the dash, and within a few seconds the power is gone, on the motorway too. Afterwards the engine often cranks but will not start.

Show the rest

What makes the repair expensive: once the inside of the pump wears, metal debris travels through the rail and contaminates the entire fuel system. At that point replacing the pump is not enough: the injectors, the rails, the tank and the lines go with it. That is the difference between a "pump replacement" and a "full system replacement" quote, that is what you should ask about.

The maker started a recall for this in the United States (NHTSA 21V586000, 2014 to 2018 328d / X5 xDrive35d / 535d / 740Ld / X3 xDrive28d). The same campaign did not run in Europe, even though the same pump works in the 320d/520d/X3 20d versions that are common right across Europe. The recall does not cover these cars.

between 79,000 and 248,000 km

What to check

  • Ask whether there has ever been a "Drivetrain fault" message or a loss of power while driving
  • Ask for the service history: if the high pressure pump was replaced, check whether the injectors and the lines were replaced with it. If not, the debris may still be in the system
  • After a cold start listen to the engine at idle: irregular running or smoke is suspect
3 more steps in the write-up

The internal fins of the exhaust gas recirculation cooler crack over time, and glycol coolant leaks into the intake, where it mixes with soot. The sticky mixture can ignite at high temperature: it can melt the plastic intake manifold and, in extreme cases, cause an engine bay fire.

Show the rest

The maker recalled the 2013 to 2018 four and six cylinder diesels, roughly 800,000 cars worldwide. The first repair attempt proved insufficient, and the leak returned in several cases: the cooler fitted since 2022, from a different supplier, is the valid fix.

So "the recall was carried out" is not enough on its own: you have to check when, and which repair was done. A first round repair does not by itself rule the problem out.

The early symptoms are white, sweet smelling exhaust smoke, slowly dropping coolant, and a rough idle.

It shows up on diesels built between 2013 and 2018. The earlier M57 is not covered by the recall.

between 108,000 and 222,000 km

What to check

  • Check the level in the expansion tank, and ask whether it has needed topping up
  • After a cold start watch the exhaust: persistent white smoke and a sweet smell mean the coolant is burning
  • Ask for the service book and find the EGR cooler recall entry: Check the date too
2 more steps in the write-up

On the early model years the timing chain of the B47 stretches faster than intended. The chain tensioner compensates for the stretch for a while and then no longer can: the chain jumps, the valve timing goes off, and in a severe case engine damage follows. The first sign is a rattling, clacking noise on a cold start that goes quiet after one to three seconds. On the B47 the chain sits at the front of the engine, not at the rear as on its predecessor, the N47. The replacement is therefore considerably less, between 1,200 and 1,800 euro, against 2,000 to 2,500 euro on the N47; if the chain has already jumped, the repair can run up to 4,500 euro. The risk is highest on units built before the end of 2015, with a reported rate of 3 to 5 per cent. 2016 was better but cases remained, and between July and December 2016 an improved chain tensioner was phased in. After mid-2016 the problem is rare, below one per cent. The engine has been in almost every four-cylinder diesel BMW since 2014, from the 1 Series to the 5 Series and from the X1 to the X4. The build date therefore says more here than the model.

above 120,000 km1,200–4,500 EUR

What to check

  • Start the engine cold and listen for the rattling noise in the first seconds
  • Ask for the build date, because units built before the end of 2015 are the risky ones
  • Ask whether the chain or the tensioner has been replaced, and ask for the invoice
2 more steps in the write-up

The B47 replaced the N47, and the maker fixed the timing chain problem. The two remaining risks on this modern diesel depend on how the car was used.

Show the rest

The first is the particulate filter. On short urban trips the regeneration cannot finish, and the filter clogs. The second is the turbo. With extended oil change intervals its bearings wear.

On this engine the service history and the type of use tell you more than the odometer. On a 200,000 km car driven on motorways and serviced often, the filter and the turbo can be in better shape than on a 90,000 km city-only car.

Where turbo wear leads in the worst case: a runaway engine. If the turbo shaft seal fails, engine oil enters the intake on the compressor side. A diesel burns that too, and this is different from a petrol engine: a diesel controls torque with the quantity of fuel injected, and it has no throttle. Once the engine runs on its own oil, cutting the injection and switching off the ignition will not stop it. The revs climb on their own until the engine destroys itself for lack of lubrication.

If this happens while driving, turning the key does not help. The only thing that works is cutting off the air: cover or plug the intake, or discharge a dry powder extinguisher into the intake tract. On a manual car you can also stall it: hold the parking brake and the brake pedal, select a high gear, and release the clutch quickly so the drivetrain chokes the engine.

This is not common, and it can happen on any turbo diesel, not only on this engine. On this engine the turbo bearing and seal wear. The warning signs are blue smoke under acceleration, an unexplained drop in oil level, and an oily charge air pipe.

What to check

  • Ask how the car was used: short daily trips or longer runs?
  • Read the fault codes for particulate filter regeneration and differential pressure
  • On a longer test drive watch the power delivery and the smoke under load
5 more steps in the write-up

Checklist

BMW X2 X2 sDrive18d

First what you would check on any car. Then the faults of this model.

Before you buy

Checklist

The printed sheet starts with what you would check on any car. What you tick stays on this device only.

On every car

Ask the owner

vinkodex.com · Before you buy it, see what can go wrong.

Official recall11 recallsShow

The manufacturer fixes these for free at a franchised dealer. Ask with the VIN whether it was done.

Most recent: 20 May 2020

20V283000AIR BAGS: AIR BAG/RESTRAINT CONTROL MODULEAIR BAGS: AIR BAG/RESTRAINT CONTROL MODULE20 May 2020 · NHTSA (USA)

BMW of North America, LLC (BMW) is recalling certain 2020 X1 xDrive28i, X1 sDrive28i, X2 xDrive28i and X2 sDrive28i, 2020 MINI Clubman Cooper S All4, 2021 MINI Hardtop 2 Door (Cooper, Cooper S, John Cooper Works and Cooper S E) and MINI Hardtop 4 Door (Cooper and Cooper S) vehicles. Due to a problem with the rollover sensor within the air bag control unit, in the event of a rollover crash, the head air bag, seat belt pretensioners and other safety systems, may not activate.

Risk: If the safety systems do not deploy as intended in a roll over crash, it may increase the risk of injury.

Remedy: BMW will notify owners, and dealers will replace the air bag control unit, free of charge. The recall began July 17, 2020. Owners may contact BMW customer service at 1-800-525-7417 or MINI customer service at 1-866-825-1525.

We could not check this: model year. The authority's notice

19V601000STEERING:LINKAGES:TIE ROD ASSEMBLYSTEERING:LINKAGES:TIE ROD ASSEMBLY14 August 2019 · NHTSA (USA)

BMW of North America, LLC (BMW) is recalling certain 2018-2019 BMW X1 sDrive28i, X1 xDrive28i, 2019 X2 xDrive28i, MINI Cooper S Convertible, Countryman, and John Cooper Works Countryman vehicles. The steering gear tie rod may have been assembled incorrectly, which may result in excessive wear of the tie rod end, eventually causing it to break.

Risk: A broken steering tie rod would lead to a loss of vehicle control, increasing the risk of a crash.

Remedy: BMW will notify owners, and dealers will inspect the vehicles and replace the tie rods and ball joints as necessary, free of charge. The recall began October 11, 2019. Owners may contact BMW customer service at 1-800-525-7417 or MINI customer service at 1-866-825-1525.

We could not check this: model year. The authority's notice

18V465000ENGINE AND ENGINE COOLING:ENGINEENGINE AND ENGINE COOLING:ENGINE12 July 2018 · NHTSA (USA)

BMW of North America, LLC (BMW) is recalling certain 2018 BMW 540d xDrive vehicles. The crankshaft sensor may be equipped with incorrect firmware, preventing the sensor from properly processing input from the crankshaft reluctor ring, possibly resulting in a vehicle stall. On September 12, 2018, BMW expanded the recall to a total of 5,309 vehicles including certain 2018-2019 BMW 540d xDrive, 230i M240i, M240i xDrive, X2 sDrive28i, X2 xDrive28i, X1 sDrive28i, X1 xDrive28i, 330i, 330i xDrive, 340i, 340i xDrive, 330i xDrive Gran Turismo, 530i, 530i xDrive, 540i, 540i xDrive, 530e, 530e xDrive, 640i xDrive Gran Turismo, 330e, 2019 430i Gran Coupe, 430i xDrive Gran Coupe, 440i Gran Coupe, 440i xDrive Gran Coupe, 430i, 430i xDrive, 440i, 440i xDrive, 740i, 740i xDrive, MINI Cooper, Cooper S, JCW, MINI Countryman (Cooper, Cooper All4, Cooper S, Cooper S All4, JCW All4), and MINI Clubman (Cooper, Cooper S, Cooper All4, Cooper S All4, JCW All4) vehicles.

Risk: A vehicle stall can increase the risk of a crash.

Remedy: BMW will notify owners, and dealers will replace the crankshaft sensor, free of charge. The recall began September 6, 2018. Owners may contact BMW customer service at 1-800-525-7417.

We could not check this: model year. The authority's notice

A12/00976/22Safety recallFire, Injuriesno date · EU Safety Gate

The micro gas generator inside the seat belt retractor may not have been manufactured to specifications. This may lead to an impairment of the restraint function in case of an accident, increasing the risk of injury. Moreover, there may be spark formation in case of a pressure release outside of the inflator damaged tube, increasing the risk of fire. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

We could not check this: model year. The authority's notice

A12/00996/24Safety recallInjuriesno date · EU Safety Gate

The integrated braking system could be compromised, which could lead to an unexpected failure of the hydraulic braking assistance, thereby requiring greater pressure on the brake pedal. This can result in a longer braking distance, as well as failure of the Anti-lock Braking System (ABS) and the Dynamic Stability Control (DSC), increasing the risk of an accident. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

We could not check this: model year. The authority's notice

A12/01039/20Safety recallInjuriesno date · EU Safety Gate

A rollover detection sensor inside the airbag control unit might be defective. Consequently, in the event of an accident in which the vehicle tips over its roof, the airbag might not properly deploy, increasing the risk of injuries of the passengers.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

We could not check this: model year. The authority's notice

A12/01342/20Safety recallFireno date · EU Safety Gate

A short circuit in the high-voltage battery could occur during initial charging due to a particle in the form of a welding bead. This may trigger a chain reaction in the battery, increasing the risk of fire.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

We could not check this: model year. The authority's notice

A12/01377/22Safety recallFireno date · EU Safety Gate

Defects in the winding of cell-internal foils in the high-voltage batteries can lead to the occurrence of increased self-discharge. This can cause high voltage cell modules to overheat, increasing the risk of fire. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

We could not check this: model year. The authority's notice

A12/01785/21Safety recallInjuriesno date · EU Safety Gate

The screws which were used to assemble seatbelts and also on the rear seats of the vehicles concerned may not have been manufactured in accordance with specifications. In some cases, the screws in question cannot withstand extreme loads, which could increase the risk of injury in the event of an accident. The product does not comply with the requirements laid down in the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

We could not check this: model year. The authority's notice

A12/1491/19Safety recallInjuriesno date · EU Safety Gate

A spherical-collar disk is missing on the tie rod end of the steering gear. Consequently, the steering gear might break due to excessive wear, leading to a loss of steering control, increasing the risk of accident.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

We could not check this: model year. The authority's notice

SR/00053/25Safety recallInjuriesno date · EU Safety Gate

The hollow shaft of the servomotor was not welded correctly. The weld may not be able to withstand high braking pressure build-up and may break. In this case, the reduced braking performance requires greater force and the braking distance may increase. In addition, the ABS and DSC brake control systems are not assisted. This increases the risk of an accident. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

We could not check this: model year. The authority's notice

Engine and transmission

B47C20U0

110 kW (150 HP) · diesel

GS6-UKL · 6-speed manual, transverse (Getrag, BMW UKL)

manual · 6 speed

Torque limit450 Nm
MakerGetrag

We built the code from the model and the gear count. The factory sheet does not state it.

Variant data

What is in this version

Factory data

Trim
X2 sDrive18d
Body
SUV
Fuel
diesel
Transmission
manual
Engine size
1995 cc
Power
110 kW (150 HP)
Drive
FWD
Production
2018–2023

Factory service interval

The manufacturer specifies this for this version. Of the mileage and the time, the one that comes first is the one that counts.

  • Air filter

    • 60,000 km or 4 years
  • Cabin (pollen) filter

    • 30,000 km or 2 years
  • Brake fluid change

    • first: 3 years, then 2 years(first change at 3 years, then every two years)
  • Engine oil and oil filter (BMW condition-based service)

    • LongLife25,000 km or 2 years
  • Fuel filter, diesel

    • 60,000 km or 2 years

Information, not an expert opinion

We write the descriptions, and we put the source next to them. A person reviews them before they go out. They are still information, not a technical expert opinion.

  • A fault on the list does not mean the car you are looking at has it.
  • A fault missing from the list does not mean the model is fault-free. Write-ups are made model by model. Not all of them are done.
  • You decide whether to buy. This is no substitute for an inspection. That needs a workshop and a history check.
Details in the terms