vinkodex.

BMW X5 X5 xDrive35d Executive common faults.

2007–2010, SUV, diesel, 286 HP.

The fault list covers: M57D30TU2 engine, ZF6HP-BMW, ZF6HP26, ZF8HP70 transmission.

What you save stays on this device only. My saves

6 fault write-ups. All are important. 15 recalls.

If you know the year, pick it. Faults for other years drop out of the list.

Before you buy

Known faults

6 important faults

critical1

The contacts between the wiring harness and the blower motor regulator wear against each other and corrode. The connection becomes unreliable, the connector heats up, the insulation of the harness is damaged, and that can lead to a short circuit and finally a vehicle fire.

Show the rest

The short circuit and the fire can happen while the engine is switched off, and also while the car is parked. A car standing in a garage can catch fire too.

According to the German technical press, in January 2021 around 430,000 cars in Germany and more than half a million worldwide were recalled for this, all E90/E91/E92/E93 3 Series. In the USA more than 700,000 2006 to 2011 3 Series cars had already been recalled for the same thing in autumn 2017, after claimants in three separate cases cited injuries. The maker disputed that the fault had ever caused personal injury or an accident.

The EU Safety Gate names it in two separate alerts: the 3 Series (A12/00390/21) and the X5/X6 (A12/01261/21).

The campaign is free, but only if it was carried out. On a fifteen year old car, ask about it, because nobody will offer it unprompted.

What to check

  • Ask the franchised dealer by VIN whether the blower motor connector campaign was carried out
  • Switch the blower on through every speed: a blower that hesitates or drops out at one speed can point to the connector fault
  • Smell the cabin with the blower running: burnt plastic or insulation is an immediate warning
2 more steps in the write-up

expensive5

The heart of the four wheel drive in the longitudinal engine BMW X models (X3, X5 and the X1 E84) is the ATC transfer case. It has two faults, and you can feel both while driving.

Show the rest

The first is wear of the clutch pack and the fluid: in a slow, tight corner (a car park, a roundabout) the car jerks and "hops", as if the drive grabbed and let go. You can also get a jerk when pulling away on a slope. The second is the plastic actuator gear: the position signal is lost, the brake, ABS and 4x4/DSC lights come on together on the dash, and a clicking is audible from the transfer case when you switch the ignition off.

Workshops often propose a full transfer case replacement straight away. But the plastic gear can be replaced on its own, and the wrong tyre size or a mixed set of tyres also imitates the jerking, because the transfer case then slips continuously. So clear up the tyres and the fault code first, before you pay for a transfer case replacement.

between 72,000 and 175,000 km

What to check

  • In a slow, tight corner (a car park) watch for jerking, binding and a "skipping" feel
  • When pulling away on light throttle, can you feel the drivetrain jerk
  • Watch the dash: 4x4, ABS, DSC and brake lights together point at the actuator
4 more steps in the write-up

On the E70/F15 (and the air sprung G05) X5 the self levelling air spring on the rear axle starts to leak over time. The characteristic picture: after standing for a long time the back sits lower than the nose; on startup the compressor runs for minutes, the car comes up, then sinks again hours later. Sinking on one side points more to that corner's air spring or to the valve block, while sinking on both points to the shared supply (compressor, dryer, lines).

Show the rest

A "compressor replacement" on its own often does not fix it: if the air spring keeps leaking, the new pump fails soon too. Air suspension is not fitted to every version, so the equipment list has to be checked separately.

The repair starts with finding the leak (soapy water, ride height sensor, valve block), not with replacing parts blind.

above 100,000 km

What to check

  • Look at the car cold, after standing at least one night: does the back sit lower than the nose, or does one rear corner sink
  • Listen to the compressor after startup: how long it runs, and whether the back comes up
  • Measure the arch height at all four corners: a difference means a sensor or a spring fault
3 more steps in the write-up

In the ZF six speed automatic (BMW codes GA6HP19Z / GA6HP26Z) the electrical connector of the valve body control leaves the gearbox housing through a plastic sleeve. That sleeve and its seals age, and they let oil through.

Show the rest

The symptom is irregular shifting, a gear slipping at higher revs, limp mode, a drivetrain fault code and a message on the display. The cause is the same in each case: the leak drops the hydraulic pressure, and the valve body cannot close the clutches with enough force.

The sleeve can be replaced without removing the gearbox, you only have to drop the oil pan. If it leaks for a long time, the slipping clutch and the overheating pump take the inside of the gearbox with them, and from then on it is a rebuild. The factory calls the oil a lifetime fill, but in practice the sleeve wears out around 60,000 to 70,000 miles, roughly 100,000 to 115,000 km.

between 100,000 and 200,000 km

What to check

  • On a lift look at the right side of the gearbox housing, above the oil pan: a wet, oily connector is the characteristic picture
  • On the test drive watch the shifts cold and warm: jerking, delay, slipping at higher revs
  • Ask for a fault code read from the gearbox controller: gear ratio fault, pressure regulation
2 more steps in the write-up

The ZF eight speed automatic (BMW Steptronic 8HP family) has two faults, and you can feel both.

Show the rest

The first is the mechatronics unit: the valve body and the control electronics in one. If the solenoids or the pressure regulation weaken, the gearbox jerks, the D/R engagement is delayed, it logs a gear ratio fault code, and finally drops into limp mode (often staying in 2nd or 3rd).

The second, and often misdiagnosed, is the connector sleeve of the mechatronics unit: the O-ring of the plastic sleeve ages, and ATF leaks from the side of the housing, exactly where the wiring harness enters. This is easy to mistake for a rear crankshaft seal. The trail starts from the driver's side of the housing, not from the clutch side.

On cars built in 2023 there was also a separate safety recall for a welding fault in the mechatronics unit. That is not the same as the wear related sleeve and the valves.

Check the fluid level, the area around the sleeve and the fault codes first; do not accept a "full gearbox replacement" quote straight away.

above 120,000 km

What to check

  • On the test drive watch for delayed D/R engagement, a jerk when shifting, and limp mode (a stuck gear)
  • Look at the driver's side of the gearbox housing where the wiring harness enters: an ATF trail from the sleeve is suspect
  • Do not confuse it with a rear crankshaft seal leak: the direction of the trail decides
3 more steps in the write-up

The automatic tailgate (an option) is covered by a maker service bulletin on the E70: the wiring harness around the hinge wears through, the spindle drive fails, the lock sticks or the connectors corrode. The symptom: the tailgate stops halfway, moves in one direction only, only clicks when you press the button, or the lower part of the split tailgate does not close fully.

Show the rest

The fault is often not the "expensive motor" but the wiring fraying at the hinge. And that can only be found with the trim off. If the seller says "the spindle has already been replaced" but the wiring is damaged, the fault will come back.

This applies only to versions with the powered tailgate.

What to check

  • Open and close the powered tailgate five times: from the key, the interior button and the button in the boot
  • Watch whether it stops halfway, reverses, or only clicks at the lock
  • On a split tailgate, try the closing of the lower part separately: there should be no gap left
2 more steps in the write-up

Checklist

BMW X5 X5 xDrive35d Executive

First what you would check on any car. Then the faults of this model.

Before you buy

Checklist

The printed sheet starts with what you would check on any car. What you tick stays on this device only.

On every car

Ask the owner

vinkodex.com · Before you buy it, see what can go wrong.

Official recall15 recallsShow

The manufacturer fixes these for free at a franchised dealer. Ask with the VIN whether it was done.

Most recent: 29 June 2021

A12/01931/23Safety recallInjuries29 June 2021 · EU Safety Gate

The propellant in the passenger airbag can deteriorate due to high humidity and temperature variations. In the event of an accident in which the airbag deploys, this could result in fragments from the inflator casing coming loose and injuring the vehicle’s occupants. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: 29/06/2021

We could not check this: model year. The authority's notice

A12/01883/23Safety recallInjuries18 February 2019 · EU Safety Gate

The propellant in the driver airbag can deteriorate due to high humidity and temperature variations. In the event of an accident in which the airbag deploys, this could result in fragments from the inflator casing coming loose and injuring the vehicle’s occupants. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: 18/02/2019

We could not check this: model year. The authority's notice

18V336000ENGINE AND ENGINE COOLING:ENGINEENGINE AND ENGINE COOLING:ENGINE23 May 2018 · NHTSA (USA)

BMW of North America, LLC (BMW) is recalling certain 2009-2013 X5 xDrive 35d diesel vehicles. The engine idler pulley bolt may loosen over time and break.

Risk: If the idler pulley bolt breaks, the vehicle may unexpectedly lose power-assisted steering, increasing the risk of a crash.

Remedy: BMW will notify owners, and dealers will replace the idler pulley bolt with an improved part, free of charge. The recall began March 11, 2019. Owners may contact BMW customer service at 1-800-525-7417.

We could not check this: model year. The authority's notice

13V564000AIR BAGS:SENSOR:OCCUPANT CLASSIFICATIONAIR BAGS:SENSOR:OCCUPANT CLASSIFICATION12 November 2013 · NHTSA (USA)

BMW of North America LLC (BMW) is recalling certain model year 2006 325i, 325xi, 330i, 330xi sedans and 325xi sports wagons, model year 2007 328i, 328xi, 335i, 335xi sedans and 328i and 328xi sports wagons, model year 2006-2007 525i, 525xi, 530i, 530xi, 550i sedans and 530xi sports wagons, model year 2006 760i sedans, model year 2006-2007 750i, 750Li, and 760Li sedans, and model year 2006 X5 sports activity vehicles, equipped with certain seat types. The front passenger seat occupant detection mat that determines if and how the passenger frontal air bag should deploy in a crash may fatigue and develop cracks which could lead to a system failure.

Risk: Should the system fail, in the event of a crash, the front passenger air bag would be deactivated, increasing the risk of personal injury.

Remedy: BMW will notify owners with an interim notification letter in January 2014 since parts are not currently available. When parts are available, BMW sent a second letter in August and dealers will repair the occupant detection mat to eliminate the possibility that it may crack, free of charge. Additionally, owners of model year 2006-2007 3 Series with standard seats, 5 Series with comfort seats, and Z4 models, will receive an extended warranty on their front passenger seat occupant detection mat. Owners may contact BMW customer relations at 1-800-525-7417 or email BMW at CustomerRelations@bmwusa.com.

We could not check this: model year. The authority's notice

13V339000FUEL SYSTEM, DIESEL: PRE-HEATERFUEL SYSTEM, DIESEL: PRE-HEATER7 August 2013 · NHTSA (USA)

BMW is recalling certain model year 2009-2010 X5 xDrive35d vehicles equipped with a diesel engine and manufactured from June 13, 2009, through November 9, 2009. The fuel filter heater, which is used for warming up the diesel fuel during vehicle operation at low outside temperatures, could experience an electrical overload condition and become permanently activated.

Risk: The fuel filter heater could remain activated even when the ignition is off and lead to a dead battery. The unit could also overheat, possibly resulting in a vehicle fire.

Remedy: BMW will notify owners, and dealers will replace the fuel filter heater, free of charge. The safety recall began on September 26, 2013. Owners may contact BMW customer relations at 1-800-525-7417.

We could not check this: model year. The authority's notice

12V019000POWER TRAIN:AUTOMATIC TRANSMISSIONPOWER TRAIN:AUTOMATIC TRANSMISSION23 January 2012 · NHTSA (USA)

BMW IS RECALLING CERTAIN MODEL YEAR 2012 X5 XDRIVE 35I SPORTS ACTIVITY VEHICLES, MANUFACTURED FROM DECEMBER 19, 2011, THROUGH DECEMBER 21, 2011. DUE TO A MANUFACTURING ERROR, ENGAGEMENT OF THE TRANSMISSION’S PARKING LOCK MAY NOT OCCUR EVEN IF THE “P” POSITION HAS BEEN SELECTED AND IS DISPLAYED.

Risk: IF THE DRIVER BELIEVES THAT THE TRANSMISSION IS IN PARK AND DOES NOT USE THE PARKING BRAKE, THE VEHICLE COULD ROLL AWAY AFTER EXITING THE VEHICLE INCREASING THE RISK OF A CRASH OR INJURY.

Remedy: BMW WILL NOTIFY OWNERS, AND DEALERS WILL REPLACE THE AUTOMATIC TRANSMISSION FREE OF CHARGE. THE SAFETY RECALL BEGAN ON FEBRUARY 2, 2012. OWNERS MAY CONTACT BMW CUSTOMER RELATIONS AND SERVICES AT 1-800-525-7417.

We could not check this: model year. The authority's notice

11V441000FUEL SYSTEM, DIESEL: PRE-HEATERFUEL SYSTEM, DIESEL: PRE-HEATER19 August 2011 · NHTSA (USA)

BMW IS RECALLING CERTAIN MODEL YEAR 2009 X5 XDRIVE35D VEHICLES EQUIPPED WITH A DIESEL ENGINE AND MANUFACTURED FROM OCTOBER 1, 2008, THROUGH JUNE 12, 2009. THE FUEL FILTER HEATER, WHICH IS USED FOR WARMING UP THE DIESEL FUEL DURING VEHICLE OPERATION AT LOW OUTSIDE TEMPERATURES, COULD EXPERIENCE AN ELECTRICAL OVERLOAD CONDITION AND BECOME PERMANENTLY ACTIVATED.

Risk: THE FUEL FILTER HEATER COULD REMAIN ACTIVATED EVEN WHEN THE IGNITION IS OFF AND LEAD TO A DEAD BATTERY. THE UNIT COULD ALSO OVERHEAT, POSSIBLY LEADING TO A VEHICLE FIRE.

Remedy: BMW WILL NOTIFY OWNERS, AND DEALERS WILL REPLACE THE FUEL FILTER HEATER FREE OF CHARGE. THE SAFETY RECALL BEGAN ON OCTOBER 11, 2011. OWNERS MAY CONTACT BMW CUSTOMER RELATIONS AND SERVICES AT 1-800-525-7417.

We could not check this: model year. The authority's notice

10V518000FUEL SYSTEM, GASOLINE:DELIVERY:FUEL PUMPFUEL SYSTEM, GASOLINE:DELIVERY:FUEL PUMP26 October 2010 · NHTSA (USA)

BMW IS RECALLING CERTAIN MODEL YEAR 2008 X5 SAVs VEHICLES WITH 6-CYLINDER ENGINES MANUFACTURED FROM NOVEMBER 1, 2007 THROUGH AUGUST 31, 2008. DUE TO A MANUFACTURING PROCESS FAULT, THE FUEL PUMP WAS NOT PRODUCED TO SPECIFICATIONS. UNDER SPECIFIC VEHICLE OPERATING CONDITIONS, THE FUEL PUMP'S COMMUTATOR COULD EXPERIENCE AN INCREASE IN WEAR.

Risk: THIS WEAR COULD LEAD TO FUEL PUMP MALFUNCTION AND ENGINE STALLING. ENGINE STALLING COULD CREATE A POTENTIAL FOR A CRASH RESULTING IN INJURY OR DEATH.

Remedy: DEALERS WILL REPLACE THE IN-TANK FUEL PUMP FREE OF CHARGE. THE SAFETY RECALL BEGAN ON JANUARY 11, 2011. OWNERS MAY CONTACT BMW AT 1-800-525-7417.

We could not check this: model year. The authority's notice

10V152000EXTERIOR LIGHTINGEXTERIOR LIGHTING15 April 2010 · NHTSA (USA)

BMW IS RECALLING CERTAIN MODEL YEAR 2010 X5 M SAV VEHICLES FOR FAILING TO COMPLY WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 108, "LAMPS, REFLECTIVE DEVICES, AND ASSOCIATED EQUIPMENT," THESE VEHICLE'S WERE EQUIPPED WITH SIDE MARKER LAMPS, BUT NOT THE POWER SUPPLY CABLES LEADING TO THE LAMPS. AS A RESULT, THE SIDE MARKER LAMPS DO NOT ILLUMINATE.

Risk: THESE VEHICLES DO NOT COMPLY WITH REQUIREMENTS OF FMVSS NO. 108.

Remedy: BMW WILL INSTALL POWER SUPPLY CABLES FOR THE FRONT SIDE MARKER LAMPS. THIS SERVICE WILL BE PERFORMED FREE OF CHARGE. THE SAFETY RECALL IS EXPECTED TO BEGIN DURING MAY 2010. OWNERS MAY CONTACT BMW AT 800-525-7417.

We could not check this: model year. The authority's notice

08V170000SUSPENSION:REARSUSPENSION:REAR11 April 2008 · NHTSA (USA)

BMW IS RECALLING 55 MY 2008 X5 SPORT UTILITY VEHICLES FOR PROBLEMS WITH THE REAR AXLE STABILIZER (ANTI-SWAY BAR). THESE VEHICLES WERE EQUIPPED WITH A SPORTS-SUSPENSION STABILIZER RATHER THAN A STANDARD SUSPENSION STABILIZER ON THE REAR AXLE.

Risk: IN CERTAIN DRIVING CONDITIONS, SUCH AS FAST LANE CHANGES AT HIGH SPEED, THE VEHICLE COULD EXPERIENCE AN 'OVER-STEER' BEHAVIOR AFFECTING VEHICLE HANDLING AND CONTROL, WHICH COULD INCREASE THE RISK OF A CRASH.

Remedy: DEALERS WILL REPLACE THE REAR AXLE STABILIZER. THE RECALL BEGAN ON MAY 14, 2008. OWNERS MAY CONTACT BMW AT 1-800-831-1117 OR VIA E-MAIL TO CUSTOMERRELATIONS@BMWUSA.COM.

We could not check this: model year. The authority's notice

05V504000POWER TRAIN:AUTOMATIC TRANSMISSIONPOWER TRAIN:AUTOMATIC TRANSMISSION1 November 2005 · NHTSA (USA)

CERTAIN PASSENGER VEHICLES MAY HAVE BEEN BUILT WITH AN INCORRECTLY MANUFACTURED AUTOMATIC TRANSMISSION PARKING PAWL GUIDE PLATE.

Risk: THIS COULD CAUSE THE PARKING LOCK SYSTEM NOT TO ENGAGE, AFTER THE TRANSMISSION IS PLACED IN THE PARK ("P") POSITION. IF THE VEHICLE WAS PARKED ON AN INCLINE, AND THE PARKING BRAKE WAS NOT ENGAGED, THIS COULD RESULT IN A VEHICLE ROLLAWAY CONDITION.

Remedy: DEALERS WILL REPAIR AND REPLACE THE AUTOMATIC TRANSMISSION GUIDE PLATE FREE OF CHARGE. THE RECALL BEGAN ON NOVEMBER 30, 2005. OWNERS MAY CONTACT BMW AT 1-800-332-4269.

We could not check this: model year. The authority's notice

A12/00783/23Safety recallInjuriesno date · EU Safety Gate

The airbag propellant may deteriorate over time, and If deployed, excessive internal pressure may cause the inflator body to burst and metal fragments could pass through the cushion material causing injury to occupants. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

We could not check this: model year. The authority's notice

A12/01261/21Safety recallFireno date · EU Safety Gate

Friction corrosion on the connector from the wiring harness to the blower regulator may cause fluctuations in the electrical resistance, which can lead to overheating and damage to the wiring harness insulation. That can result in a short circuit, leading to a vehicle fire, even if the vehicle is parked.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

We could not check this: model year. The authority's notice

A12/01382/23Safety recallInjuriesno date · EU Safety Gate

The driver or passenger airbag inflator may malfunction. In the event of an airbag activation this can lead to the release of fragments from the generator housing, increasing the risk of injury. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

We could not check this: model year. The authority's notice

A12/01981/24Safety recallInjuriesno date · EU Safety Gate

A seam on the inflator housing of the driver airbag may not have been correctly welded. In case of accident, when the airbag is deployed, the inflator can burst, releasing metal parts which could cause injuries. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

We could not check this: model year. The authority's notice

Engine and transmission

1 engines · 3 transmissions

M57D30TU2 · 3.0d/xDrive30d

173–210 kW (235–286 HP) · diesel

ZF6HP-BMW · 6-speed automatic, longitudinal (ZF 6HP19/21, BMW GA6HP)

automatic · 6 speed

Torque limit450 Nm
MakerZF

We built the code from the model and the gear count. The factory sheet does not state it. More than one transmission is possible. The gear count does not tell them apart. The code is on the side of the transmission.

Variant data

What is in this version

Factory data

Trim
X5 xDrive35d Executive
Body
SUV
Fuel
diesel
Transmission
automatic
Engine size
2993 cc
Power
210 kW (286 HP)
Drive
AWD
Production
2007–2010

Factory service interval

The manufacturer specifies this for this version. Of the mileage and the time, the one that comes first is the one that counts.

  • Air filter

    • 60,000 km or 4 years
  • Cabin (pollen) filter

    • 30,000 km or 2 years
  • Brake fluid change

    • first: 3 years, then 2 years(first change at 3 years, then every two years)
  • Engine oil and oil filter (BMW condition-based service)

    • LongLife25,000 km or 2 years
  • Automatic gearbox oil (ZF 8HP / 6HP)

    • 160,000 km
  • Fuel filter, diesel

    • 60,000 km or 2 years

Information, not an expert opinion

We write the descriptions, and we put the source next to them. A person reviews them before they go out. They are still information, not a technical expert opinion.

  • A fault on the list does not mean the car you are looking at has it.
  • A fault missing from the list does not mean the model is fault-free. Write-ups are made model by model. Not all of them are done.
  • You decide whether to buy. This is no substitute for an inspection. That needs a workshop and a history check.
Details in the terms