vinkodex.

BMW X7 X7 M50i common faults.

2019–2022, SUV, petrol, 530 HP.

The fault list covers: N63B44T3 engine, ZF8HP75, ZF8HP90 transmission.

What you save stays on this device only. My saves

4 fault write-ups. All are important. 17 recalls.

If you know the year, pick it. Faults for other years drop out of the list.

Before you buy

Known faults

4 important faults

critical2

N63 V8: failing piezo injectors and hydraulic lock in the cylinder

critical

On this engine the injectors were also listed as parts to be replaced in the maker's own programme, which means their failure is a known one. A faulty injector puts too much fuel into the cylinder. The liquid cannot be compressed, so the piston hits it on its way up: this is hydraulic lock, and it can damage the connecting rod bearing and the connecting rod as well. The early sign is rough running and hard starting. The fault can start from 60,000 km. The maker ran a separate programme for this engine, called the Customer Care Package, from December 2014. The franchised dealers had to check seven parts: the timing chain, the fuel injectors, the mass air flow sensor, the crankcase vent lines, the battery, the vacuum pump and the low pressure fuel sensor. These had to be replaced free of charge, even if the car had already fallen out of the four-year, 50,000-mile warranty. The same programme also shortened the oil change interval: 10,000 miles or one year instead of 15,000 miles or two years. Before buying it is therefore worth asking whether this programme was carried out on the car.

above 60,000 km

What to check

  • Ask whether the Customer Care Package was carried out, and whether the injectors were replaced
  • Start the engine cold and watch for hard starting and rough running
  • Read the fault memory and look for a code reporting a misfire on a specific cylinder
2 more steps in the write-up

N63 V8: a stretching timing chain and broken guides blocking the oil system

critical

The timing chain stretches between 80,000 and 120,000 km, and the plastic chain guides break. The broken pieces end up in the sump and block the lubrication system. From then on the engine is starved of oil, which takes the bearings and the turbochargers with it. The early sign is a metallic rattling from the front of the engine on a cold start. The stretching of the chain also features in the American class actions, alongside the extreme oil consumption. The maker ran a separate programme for this engine, called the Customer Care Package, from December 2014. The franchised dealers had to check seven parts: the timing chain, the fuel injectors, the mass air flow sensor, the crankcase vent lines, the battery, the vacuum pump and the low pressure fuel sensor. These had to be replaced free of charge, even if the car had already fallen out of the four-year, 50,000-mile warranty. The same programme also shortened the oil change interval: 10,000 miles or one year instead of 15,000 miles or two years. Before buying it is therefore worth asking whether this programme was carried out on the car.

between 80,000 and 120,000 km

What to check

  • Start the engine cold and listen for metallic rattling from the front of the engine
  • Ask whether the Customer Care Package was carried out, and whether the chain was replaced
  • Read the fault memory and look for a code reporting a camshaft position deviation
2 more steps in the write-up

expensive2

N63 V8: the valve stem seals leak and oil consumption is extreme

expensive

The valve stem seals start to lose their sealing from 90,000 km, and oil gets into the combustion chamber along the valve stem. The burning oil lays soot on the piston rings, they start to stick, and from then on the consumption grows further; the lubrication also gets tighter and the exhaust smokes. The scale of the consumption on this engine is extraordinary. In the American class action the plaintiffs report around one litre every 1,200 km, and one of them one litre every 1,600 km. In 2013 the maker issued a new oil consumption standard for this engine in a bulletin, and took the position that this is not a defect: according to it every one of its engines may use that much. The lawsuit points out that with this standard the owner has to top up the oil twenty times before reaching the factory 15,000-mile oil change interval. The maker ran a separate programme for this engine, called the Customer Care Package, from December 2014. The franchised dealers had to check seven parts: the timing chain, the fuel injectors, the mass air flow sensor, the crankcase vent lines, the battery, the vacuum pump and the low pressure fuel sensor. These had to be replaced free of charge, even if the car had already fallen out of the four-year, 50,000-mile warranty. The same programme also shortened the oil change interval: 10,000 miles or one year instead of 15,000 miles or two years. Before buying it is therefore worth asking whether this programme was carried out on the car. The repair means opening the cylinder head, and because of the V layout of the engine on both sides.

above 90,000 km

What to check

  • Ask how much oil has to be added between two changes, and ask for a figure
  • Ask whether the Customer Care Package programme was carried out, and ask for the confirmation
  • Read the service book: the shortened, one-year oil change cycle is expected here
2 more steps in the write-up

ZF 8HP automatic: mechatronics unit and connector sleeve leak

expensive

The ZF eight speed automatic (BMW Steptronic 8HP family) has two faults, and you can feel both.

Show the rest

The first is the mechatronics unit: the valve body and the control electronics in one. If the solenoids or the pressure regulation weaken, the gearbox jerks, the D/R engagement is delayed, it logs a gear ratio fault code, and finally drops into limp mode (often staying in 2nd or 3rd).

The second, and often misdiagnosed, is the connector sleeve of the mechatronics unit: the O-ring of the plastic sleeve ages, and ATF leaks from the side of the housing, exactly where the wiring harness enters. This is easy to mistake for a rear crankshaft seal. The trail starts from the driver's side of the housing, not from the clutch side.

On cars built in 2023 there was also a separate safety recall for a welding fault in the mechatronics unit. That is not the same as the wear related sleeve and the valves.

Check the fluid level, the area around the sleeve and the fault codes first; do not accept a "full gearbox replacement" quote straight away.

above 120,000 km

What to check

  • On the test drive watch for delayed D/R engagement, a jerk when shifting, and limp mode (a stuck gear)
  • Look at the driver's side of the gearbox housing where the wiring harness enters: an ATF trail from the sleeve is suspect
  • Do not confuse it with a rear crankshaft seal leak: the direction of the trail decides
3 more steps in the write-up

Checklist

BMW X7 X7 M50i

First what you would check on any car. Then the faults of this model.

Before you buy

Checklist

The printed sheet starts with what you would check on any car. What you tick stays on this device only.

On every car

Ask the owner

Faults of this model

vinkodex.com · Before you buy it, see what can go wrong.

Official recall17 recallsShow

The manufacturer fixes these for free at a franchised dealer. Ask with the VIN whether it was done.

Most recent: 25 September 2025

25V644000ELECTRICAL SYSTEM:STARTER ASSEMBLYELECTRICAL SYSTEM:STARTER ASSEMBLY25 September 2025 · NHTSA (USA)

BMW of North America, LLC (BMW) is recalling certain 2020 340I, X6, 2020-2025 840I, 2020-2022 740LI, 2019-2020 X7, and X5 vehicles. After repeated attempts, the starter motor may overheat from an electrical overload.

Risk: An overheated starter motor can ignite nearby combustible material in the engine compartment, increasing the risk of a fire.

Remedy: Dealers will replace the engine starter, free of charge. This recall includes vehicles repaired under recall 24V576 and those owners will need to have their vehicle repaired again. Owner notification letters were mailed February 9, 2026. Owners may contact BMW customer service at 1-800-525-7417. Vehicle Identification Numbers (VINs) involved in this recall became searchable on NHTSA.gov November 17, 2025.

The authority's notice

24V576000ELECTRICAL SYSTEM:STARTER ASSEMBLYELECTRICAL SYSTEM:STARTER ASSEMBLY1 August 2024 · NHTSA (USA)

BMW of North America, LLC is recalling certain 2019-2020 X5, X7, 2020 3 Series Sedan, X6, 2020-2021 7 Series Sedan, 2020 8 Series Convertible, 8 Series Coupe, and 2020 8 Series Gran Coupe vehicles. Please see the recall report for the complete list of models. In the event the starter motor fails, repeated attempts to start the vehicle can cause the starter motor to overheat from an electrical overload.

Risk: A starter motor that overheats can ignite nearby combustible material in the engine compartment, increasing the risk of a fire.

Remedy: Dealers will update the vehicle software, free of charge. Owner notification letters were mailed September 27, 2024. Owners may contact BMW customer service at 1-800-525-7417.

The authority's notice

22V670000SEATSSEATS7 September 2022 · NHTSA (USA)

BMW of North America, LLC (BMW) is recalling certain 2019-2022 BMW X7 xDrive40i, X7 Drive50i, X7 M50i vehicles with third-row seats. One or more of the compression springs that lock the backrest may not have been installed properly, and could dislodge or detach.

Risk: In a crash, the seat backrest may not fully lock, increasing the risk of injury.

Remedy: Dealers will inspect the third-row seat and, if necessary, remove and reinstall improperly installed compression springs, and reinstall any missing springs, free of charge. Owner notification letters were mailed November 4, 2022. Owners may contact BMW customer service at 1-800-525-7417.

The authority's notice

22V267000VISIBILITY:SUN/MOON ROOF ASSEMBLYVISIBILITY:SUN/MOON ROOF ASSEMBLY20 April 2022 · NHTSA (USA)

BMW of North America, LLC (BMW) is recalling certain 2022 4 Series Gran Coupe (430i, 430i xDrive, M440i xDrive); 2019-2022 X5 sDrive40i, X5 xDrive40i, X5 xDrive50i, X5 M50i, X5M; 2021-2022 X5 xdrive45e; 2020-2022 X6 sDrive40i, X6 xDrive40i, X6 xDrive50i, X6M and 2019-2023 X7 xDrive40i, X7 xDrive50i, X7 M50i, X7 xDrive60i, X7 M60i, X7M, Alpina XB7 vehicles. The roof function control unit may be programmed incorrectly, allowing the sunroof to close without the key fob present inside the vehicle. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard number 118, "Power-Operated Window Systems."

Risk: A sunroof that closes without the key fob present inside the vehicle can increase the risk of injury.

Remedy: Dealers will reprogram the roof function control unit, free of charge. Owner notification letters were mailed June 20, 2022. Owners may contact BMW customer service at 1-800-525-7417.

The authority's notice

21V096000BACK OVER PREVENTION: SENSING SYSTEM: CAMERABACK OVER PREVENTION: SENSING SYSTEM: CAMERA19 February 2021 · NHTSA (USA)

BMW of North America, LLC (BMW) is recalling certain 2019-2021 X3 sDrive30i, X3 xDrive30i, X3 M40i, X3M, X4 xDrive30i, X4 M40i, M550i, X4M, X5 sDrive40i, X5 xDrive40i, X5 xDrive50i, X5M, X5 M50i, X7 xDrive40i, X7 xDrive50i, X7 M50i, Alpina XB7, 330i, 330i xDrive, M340i, M340i xDrive, and 8 Series Coupe, Convertible and Grand Coupe, 840i, 840i xDrive, M850i xDrive, M8, 2020-2021 530e, 530e xDrive, 330e, 330e xDrive, 745Le, 745Le xDrive, X5 xDrive45e, X3 xDrive30e, X6 sDrive40i, X6 xDrive40i, X6 xDrive50i, X6 M50i, X6M, 530i, 530i xDrive, 540i, 540i xDrive, M550i xDrive, M5, 740i, 740Li, 740Li xDrive, M760i Drive, M760Li xDrive, 750Li xDrive Alpina, Alpina B7 xDrive, and 2021 4 Series Coupe 430i, 430i xDrive, M440i xDrive vehicles. When shifting into Reverse, a small portion of the rearview image may be obscured, or the screen may not illuminate. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 111, "Rear Visibility."

Risk: If the driver relies on only the rearview camera image, the missing or reduced rearview image view can increase the risk of a crash or injury.

Remedy: BMW will notify owners, and dealers will inspect the rearview camera software and update it if necessary, free of charge. The recall began April 16, 2021. Owners may contact BMW customer service at 1-800-525-7417.

The authority's notice

21V062000SERVICE BRAKES, HYDRAULICSERVICE BRAKES, HYDRAULIC10 February 2021 · NHTSA (USA)

BMW of North America, LLC (BMW) is recalling certain 2020-2021 8 Series Coupe, Grand Coupe and convertible 840i, 840i xDrive, M850i xDrive, M8 and 740 Li, 740 Li xDrive, 750 Li xDrive, M760 Li xDrive, X6 sDrive40i, X6 xDrive40i, X6 xdrive50i, X6 M50i, X6M, and 2019-2021 X5 sDrive40i, X5 xDrive40i, X5 xDrive50i, X5 M50i, X5M, X7 xDrive40i, X7 xDrive50i, X7 M50i, and 2021 M3, M3 Competition, M4 Coupe, M4 Competition Coupe, X5 xDrive45e, 745 Le xDrive. The rotor and shaft within the integrated brake system may not have been welded properly and could separate during a hard braking event, possibly resulting in a loss of the Antilock Brake System (ABS) and braking assistance.

Risk: A loss of ABS and a reduction in braking assistance can increase the risk of a crash.

Remedy: BMW will notify owners, and dealers will replace the integrated brake system, free of charge. Owner notification letters were mailed on May 25, 2021. Owners may contact BMW customer service at 1-800-525-7417.

The authority's notice

20V678000SUSPENSION:FRONT:CONTROL ARMSUSPENSION:FRONT:CONTROL ARM4 November 2020 · NHTSA (USA)

BMW of North America, LLC (BMW) is recalling certain 2020 X5 sDrive40i, xDrive40i, X5 M50i, X5M, X7 xDrive40i, X7 M50i, X6 xDrive40i, X6 M50i and X6M vehicles and 2021 X5 xDrive45e vehicles. The weld between the front axle support and the right front control arm bearing bracket may separate.

Risk: If the weld between the front axle support and the right front control arm bearing bracket separates, vehicle handling and control may be affected, increasing the risk of a crash.

Remedy: BMW will notify owners, and dealers will replace the front axle support, free of charge. The recall began December 18, 2020. Owners may contact BMW customer service at 1-800-525-7417.

The authority's notice

20V528000EXTERIOR LIGHTING:HEADLIGHTSEXTERIOR LIGHTING:HEADLIGHTS1 September 2020 · NHTSA (USA)

BMW of North America, LLC (BMW) is recalling certain 2020-2021 X5 sDrive40i, xDrive40i, xDrive50i, X5 M50i, X5M, X6 sDrive40i, xDrive40i, X6 M50i, X6M, X7 M50i and 2021 X5 xDrive45e vehicles. The headlamps may allow a blue light to illuminate. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard number 108, "Lamps, Reflective Devices, and Associated Equipment."

Risk: Oncoming drivers may be confused by the blue light of approaching vehicles, which could potentially increase the risk of a crash.

Remedy: BMW will notify owners, and dealers will inspect the headlamps and, if necessary, replace them, free of charge. The recall began October 30, 2020. Owners may contact BMW customer service at 1-800-525-7417.

The authority's notice

20V465000POWER TRAIN:AUTOMATIC TRANSMISSIONPOWER TRAIN:AUTOMATIC TRANSMISSION7 August 2020 · NHTSA (USA)

BMW of North America, LLC (BMW) is recalling certain 2020 X5 sDrive 40i, X5 xDrive 40i and one X7 xDrive 40i vehicle. The starter motor may have an extra bolt that could potentially fall into the transmission housing and cause an engine stall.

Risk: An engine stall increases the risk of a crash.

Remedy: BMW will notify owners, and dealers will inspect the starter motor for the extra bolt, removing it if necessary. Dealers will also inspect the starter for damage, and check if the bolt has fallen into the transmission housing, replacing any damaged parts as necessary. All repairs will be performed free of charge. The recall began on October 2, 2020. Owners may contact BMW customer service at 1-800-525-7417.

The authority's notice

20V052000EXTERIOR LIGHTINGEXTERIOR LIGHTING30 January 2020 · NHTSA (USA)

BMW of North America, LLC (BMW) is recalling certain 2020 X7 xDrive40i and X7 xDrive50i vehicles. The rear reflex reflectors may not reflect an adequate amount of light. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 108, "Lamps, Reflective Devices, and Associated Equipment."

Risk: An inadequate amount of reflected light will decrease the vehicle's visibility to other drivers, increasing the risk of a crash.

Remedy: BMW will notify owners, and dealers will replace both rear reflex reflectors, free of charge. The recall began March 30, 2020. Owners may contact BMW customer service at 1-800-525-7417.

The authority's notice

19V631000STEERING:RACK AND PINION:RACKSTEERING:RACK AND PINION:RACK28 August 2019 · NHTSA (USA)

BMW of North America, LLC (BMW) is recalling certain 2020 X5 sDrive40i, X5 xDrive40i, X5 M50i, X7 xDrive40i and X7 M50i vehicles. The steering rack pinion teeth may break under load, resulting in a loss of steering control.

Risk: A loss of steering control increases risk of a crash.

Remedy: BMW will notify owners, and dealers will replace the steering rack, free of charge. The recall began August 21, 2019. Owners may contact BMW customer service at 1-800-525-7417.

The authority's notice

A12/00307/21Safety recallInjuriesno date · EU Safety Gate

The steering spindle may not have been properly bolted and could become detached. As a result the steering control would be lost, increasing the risk of an accident.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

The authority's notice

A12/00590/21Safety recallInjuriesno date · EU Safety Gate

Defective hydraulic unit of the braking system may cause a limited braking support and increased braking distance. Moreover, in such cases the ABS system would not be available. This will lead to increased risk of an accident.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

The authority's notice

A12/01428/22Safety recallInjuriesno date · EU Safety Gate

Due to a faulty installation of the compression springs of the lock in the third seat row, the backrest may not be fully locked. This could lead to an increased risk of injury in the event of an accident. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

The authority's notice

A12/01855/20Safety recallInjuriesno date · EU Safety Gate

Due to defective welding, the push bars on the front axle beam may become detached. Moreover, a failure of the welding quality may result in a crack of the bearing bracket. This could lead to loss of wheel control, increasing the risk of an accident.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

The authority's notice

A12/02466/24Safety recallFireno date · EU Safety Gate

The software-based overload protection function cannot sufficiently prevent the starter being overloaded in the event of repeated long start-up attempts. The starter may overheat or sparks may be produced as a result of an increased current flow. This increases the risk of a fire. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

The authority's notice

SR/03823/25Safety recallFireno date · EU Safety Gate

The engine starter’s electrical contacts may overheat and cause the vehicle to start improperly. Continued starting attempts can intensify the overheating and ignite surrounding components, potentially leading to a vehicle fire while driving or shortly after parking. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

The authority's notice

Engine and transmission

1 engines · 2 transmissions

N63B44T3

390 kW (530 HP) · petrol

ZF8HP75 · 8-speed automatic, longitudinal (ZF 8HP75)

automatic · 8 speed

Torque limit750 Nm
MakerZF

We built the code from the model and the gear count. The factory sheet does not state it. More than one transmission is possible. The gear count does not tell them apart. The code is on the side of the transmission.

Variant data

What is in this version

Factory data

Trim
X7 M50i
Body
SUV
Fuel
petrol
Transmission
automatic
Engine size
4395 cc
Power
390 kW (530 HP)
Drive
AWD
Production
2019–2022

Factory service interval

The manufacturer specifies this for this version. Of the mileage and the time, the one that comes first is the one that counts.

  • Air filter

    • 60,000 km or 4 years

  • Cabin (pollen) filter

    • 30,000 km or 2 years

  • Brake fluid change

    • first: 3 years, then 2 years(first change at 3 years, then every two years)

  • Engine oil and oil filter (BMW condition-based service)

    • LongLife25,000 km or 2 years

  • Spark plugs, petrol

    • 60,000 km or 6 years
All G07 versions

Information, not an expert opinion

We write the descriptions, and we put the source next to them. A person reviews them before they go out. They are still information, not a technical expert opinion.

  • A fault on the list does not mean the car you are looking at has it.
  • A fault missing from the list does not mean the model is fault-free. Write-ups are made model by model. Not all of them are done.
  • You decide whether to buy. This is no substitute for an inspection. That needs a workshop and a history check.
Details in the terms