vinkodex.

Ford Focus 1.5 TDCi 120hp Titanium common faults.

2014–2018, estate, diesel, 120 HP.

The fault list covers: XWDA, XWDB, XWDC, XWDD, XWDE engine, IB6, MMT6 transmission.

What you save stays on this device only. My saves

7 fault write-ups. All are important. 5 recalls.

If you know the year, pick it. Faults for other years drop out of the list.

Before you buy

Known faults

7 important faults

critical3

2.0 GDI: the canister purge valve stalls the engine

critical

The canister purge valve (CPV) can malfunction. According to the authority this creates excessive vacuum in the fuel vapour management system, the engine stalls while driving without warning, and it cannot be restarted. The authority describes this as a crash risk.

Show the rest

Ford recalled it twice: in October 2018 (18V735000), then in June 2026 for the cars repaired incorrectly (26V369000). The second campaign states that the valve causes the engine to stall unexpectedly while driving.

What to check

  • Ask whether the engine has ever stalled while driving, even once
  • With the engine idling, listen for the purge valve clicking irregularly
  • Check for a fuel smell around the filler cap, or a deformed tank
2 more steps in the write-up

6-speed manual: the clutch fractures

critical

The clutch can fracture, the break damages the transmission case, and gearbox oil can leak from it. The car may become immobile, and the leaking oil can ignite on the hot engine or exhaust.

Show the rest

Ford issued three campaigns. The first went out in March 2018 (18V169000) for the 1.6 EcoBoost with the 6-speed manual, the second in November 2018 (18V845000) for the 1.0 EcoBoost cars, and the third in June 2026 (26V376000) because part of the earlier repairs had been done incorrectly. A car that has had the repair is not necessarily in order.

In the European range the 1.0 EcoBoost with the 6-speed manual is the most common Focus.

What to check

  • Pull away from a standstill several times: the clutch must not shudder, slip or kick
  • Pull away on a hill using the clutch: slipping shows up here first
  • Look under the car around the transmission housing: fresh or dried oil traces can mean a break
2 more steps in the write-up

Door latch: the latching component breaks and the door can open while driving

critical

A component inside the door latch breaks, so the latch no longer holds properly: the door is hard to close, or it only catches on the first detent. The driver and the passenger may believe the door is properly shut when it is not, and it can open while driving.

Show the rest

Ford issued five campaigns between 2015 and 2023, and two of them, 20V331000 and 23V775000, recalled cars where the earlier repair had not been carried out properly. The 2020 campaign names six models: the 2011-2014 Fiesta, the 2012-2015 Focus, the 2013-2015 C-Max, the 2014-2016 Transit Connect, the 2015 Mustang and the 2013-2014 Fusion. The factory repair fits a revised door latch.

What to check

  • Close all four doors with normal force: none should need slamming, and none should bounce back
  • Push each door half shut: it must hold on the first detent, with no play
  • Open and close each one from the outside and the inside, including the child locks at the rear
2 more steps in the write-up

expensive4

MMT6 manual: worn shift mechanism, hard shifting when cold

expensive

The gearbox itself is reliable, but the shift mechanism wears noticeably between 100,000 and 150,000 km. Shifting becomes stiff, and it is most obvious when cold: the lever does not want to find its place, or the gear only goes in with force.

Show the rest

At high mileage the synchros on the first two gears wear out, and then the shift grates. The gearbox comes with a dual-mass flywheel, which is not the most durable part either.

between 100,000 and 150,000 km

What to check

  • Set off from cold: both first and second must engage without snagging
  • Stop and select reverse: it must not grate or need force
  • While rolling, change down into second: this is where worn synchros are audible
2 more steps in the write-up

Timing belt and tensioner: a non-original belt snaps sooner

expensive

The timing belt and its tensioner pulley are the weakest point of this engine. The factory specification is 150 000 kilometres or ten years, and whichever of the two comes first is what counts. A non-original belt, however, snaps at around 100 000 kilometres already, so the origin of the part is a question here too.

Show the rest

The quality of the change matters just as much. If the correct locking tools are not used during the belt change, the bar of the tensioner pulley is damaged, and the belt can jump.

If the belt snaps, the damage typically affects the valve rockers, and the valves themselves mostly survive. Even so the repair starts with opening up the cylinder head.

There are two production batches worth asking about separately. The examples built between December 2014 and May 2015 had a defective camshaft gear, which caused rapid cracking and valve damage. A campaign was launched for this in 2015 (16B42), in which the pulleys were replaced on several models.

The early sign is a squealing or droning noise from the direction of the timing belt cover.

between 100,000 and 150,000 km

What to check

  • Start it cold and listen to the noise from the direction of the timing belt cover
  • Ask for the invoice of the timing belt change: find out whether the tensioner pulley was replaced too
  • Ask whether a factory or an aftermarket belt went in: a non-original one snaps sooner
3 more steps in the write-up

EGR cooler: it cracks and the coolant goes into the intake

expensive

The EGR cooler can crack from the thermal load, and coolant gets into the intake through the crack. The fault is reported at around 120 000 kilometres.

Show the rest

The most telling sign is black foam in the expansion tank: the recirculated exhaust gas sooties up the coolant. With it comes the coolant going down while there is no leak from outside, white smoke from the exhaust, and the engine tending to run hot.

In severe cases the fluid getting into the intake causes a hydraulic lock, and engine damage follows from that. The fluid is not compressible, so once it is in the cylinder it is the connecting rod that has to give. The repair is replacement of the cooler, and it is not worth putting it off.

above 120,000 km

What to check

  • Open the expansion tank on a cold engine: black foam or dirty fluid indicates a cracked EGR cooler
  • Look at the coolant level and ask whether it has had to be topped up
  • Look for a puddle under the car: if the level drops but there is no puddle, the fluid goes inwards
3 more steps in the write-up

IB6 manual: little oil, leaks, and the synchro noise that follows

expensive

The gearbox is light and compact and reliable, but the small oil quantity makes it sensitive to leaks: not much has to escape before the level becomes critical.

Show the rest

Most complaints about synchro noise actually come from this, from the low oil level rather than from the synchro itself. Beyond that the input shaft bearing can wear out and reverse can fail. Every version comes with a dual-mass flywheel, which is not the most durable part.

What to check

  • Look at the gearbox housing from underneath: fresh oil means a leak, and here that is the main cause
  • Ask when the oil level was last checked and whether it has ever been topped up
  • While rolling, change down into second and third: grating means worn synchros
2 more steps in the write-up

Checklist

Ford Focus 1.5 TDCi 120hp Titanium

First what you would check on any car. Then the faults of this model.

Before you buy

Checklist

The printed sheet starts with what you would check on any car. What you tick stays on this device only.

On every car

Ask the owner

Faults of this model

vinkodex.com · Before you buy it, see what can go wrong.

Official recall5 recallsShow

The manufacturer fixes these for free at a franchised dealer. Ask with the VIN whether it was done.

Most recent: 9 June 2026

26V369000FUEL SYSTEM, GASOLINE:STORAGE:EVAPORATIVE EMISSIONS:CANISTERFUEL SYSTEM, GASOLINE:STORAGE:EVAPORATIVE EMISSIONS:CANISTER9 June 2026 · NHTSA (USA)

Ford Motor Company (Ford) is recalling certain 2012-2018 Focus vehicles previously repaired incorrectly under recall number 18V735. The Canister Purge Valve (CPV) may malfunction, causing the engine to stall unexpectedly while driving.

Risk: An engine that stalls while driving increases the risk of a crash.

Remedy: Dealers will update the powertrain control module (PCM) software, free of charge. Owner notification letters were mailed July 29, 2026. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 26S40. Vehicle Identification Numbers (VINs) involved in this recall will become searchable on NHTSA.gov on July 6,2026.

The authority's notice

19V515000FUEL SYSTEM, GASOLINE:STORAGEFUEL SYSTEM, GASOLINE:STORAGE5 July 2019 · NHTSA (USA)

Ford Motor Company (Ford) is recalling certain 2012 and 2017 Focus vehicles equipped with 2.0L GDI gasoline engines and 2013-2014 Focus ST vehicles equipped with 2.0L GTDI engines, previously recalled under 18V-735. The affected vehicles did not have the Powertrain Control Module (PCM) updated as intended. Therefore, the Canister Purge Valve (CPV) may malfunction, possibly causing excessive vacuum in the fuel vapor management system.

Risk: The excessive vacuum may result in an engine stall while driving, without warning and without the ability to restart the vehicle, increasing the risk of a crash.

Remedy: Ford will notify owners, and dealers will reprogram the Powertrain Control Module. Dealers will also check for fault codes and replace the CPV as needed. If the CPV is replaced, dealers will inspect and replace the carbon canister, fuel tank and fuel delivery module as necessary. The recall began July 29, 2019. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 19S22.

The authority's notice

18V735000FUEL SYSTEM, GASOLINE:STORAGEFUEL SYSTEM, GASOLINE:STORAGE22 October 2018 · NHTSA (USA)

Ford Motor Company (Ford) is recalling certain 2012-2018 Ford Focus vehicles with a 2.0L GDI or 2.0L GTDI engine. The Canister Purge Valve (CPV) may malfunction, possibly causing excessive vacuum in fuel vapor management system.

Risk: The excessive vaccuum may result in an engine stall while driving, without warning and without the ability to restart the vehicle, increasing the risk of a crash.

Remedy: Ford will notify owners, and dealers will reprogram the Powertrain Control Module. Dealers will also check for fault codes and replace the CPV as needed. If the CPV is replaced, dealers will inspect and replace the carbon canister, fuel tank and fuel delivery module as necessary. The recall began August 19, 2019. Owners may contact Ford Customer service at 1-866-436-7332. Ford's number for this recall is 18S32. Note: Until the vehicle is serviced for this concern, owners are advised to keep the fuel tank at least halfway full.

The authority's notice

18V169000POWER TRAIN:MANUAL TRANSMISSIONPOWER TRAIN:MANUAL TRANSMISSION12 March 2018 · NHTSA (USA)

Ford Motor Company (Ford) is recalling certain 2013-2014 Ford Fusion vehicles equipped with a 1.6L GTDI engine and 6-speed manual transmission and 2015-2016 Ford Focus vehicles equipped with a 1.0L GTDI engine and 6-speed manual transmission. Also included are four 2017 Ford Focus vehicles that had clutch replacements with potentially affected parts. The clutch may fracture, resulting in damage to the transmission assembly and possibly a transmission fluid leak.

Risk: A transmission fluid leak in the presence of an ignition source such as hot engine or exhaust components can increase the risk of a fire.

Remedy: Ford will notify owners, and dealers will update the Focus vehicles with software that detects and prevents prolonged clutch slip, and will replace the clutch, as necessary, free of charge. Owners of Fusion vehicles will have their clutch assembly replaced free of charge. The recall began August 3, 2018. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 18S07.

The authority's notice

16V698000LATCHES/LOCKS/LINKAGES:HATCHBACK/LIFTGATE:LOCKLATCHES/LOCKS/LINKAGES:HATCHBACK/LIFTGATE:LOCK28 September 2016 · NHTSA (USA)

Ford Motor Company (Ford) is recalling certain model year 2013-2017 Ford Focus hatchback vehicles manufactured February 14, 2012, to August 26, 2016 and equipped with a manual transmission. The hatchback of the affected vehicles may be unlatched with a single press of the interior latch release button. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 206, "Door Locks and Door Retention Components."

Risk: With only a single press needed, the driver may accidently unlatch the hatchback, increasing the risk of injury to any unsecured passengers in the back.

Remedy: Ford will notify owners, and dealers will reprogram the Body Control Module with updated software, free of charge. The recall began February 10, 2017. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 16C13.

The authority's notice

Engine and transmission

5 engines · 2 transmissions

XWDA · 1.5 TDCI FLH

88 kW (120 HP) · diesel

IB6 · 6-speed manual

manual · 6 speed

Torque limit285 Nm
MakerFord/Getrag

We built the code from the model and the gear count. The factory sheet does not state it. More than one engine code is possible. The fault list shows the faults of each. More than one transmission is possible. The gear count does not tell them apart. The code is on the side of the transmission.

Variant data

What is in this version

Factory data

Trim
Titanium
Body
estate
Fuel
diesel
Transmission
manual
Engine size
1499 cc
Power
88 kW (120 HP)
Drive
FWD
Production
2014–2018

Factory service interval

The manufacturer specifies this for this version. Of the mileage and the time, the one that comes first is the one that counts.

  • Air filter

    • 60,000 km or 4 years

  • Cabin (pollen) filter

    • 30,000 km or 2 years

  • Brake fluid change

    • first: 3 years, then 2 years(first change at 3 years, then every two years)

  • Fuel filter, diesel

    • 60,000 km or 2 years
All Mk3.5 versions

Information, not an expert opinion

We write the descriptions, and we put the source next to them. A person reviews them before they go out. They are still information, not a technical expert opinion.

  • A fault on the list does not mean the car you are looking at has it.
  • A fault missing from the list does not mean the model is fault-free. Write-ups are made model by model. Not all of them are done.
  • You decide whether to buy. This is no substitute for an inspection. That needs a workshop and a history check.
Details in the terms