vinkodex.

Ford Focus 1.6 TDCi 115hp First Edition common faults.

2011–2014, saloon, diesel, 115 HP.

The fault list covers: T1DA, T1DB engine, IB6, MMT6, MTX75 transmission.

What you save stays on this device only. My saves

6 fault write-ups. All are important. 5 recalls.

If you know the year, pick it. Faults for other years drop out of the list.

Before you buy

Known faults

6 important faults

critical2

2.0 GDI: the canister purge valve stalls the engine

critical

The canister purge valve (CPV) can malfunction. According to the authority this creates excessive vacuum in the fuel vapour management system, the engine stalls while driving without warning, and it cannot be restarted. The authority describes this as a crash risk.

Show the rest

Ford recalled it twice: in October 2018 (18V735000), then in June 2026 for the cars repaired incorrectly (26V369000). The second campaign states that the valve causes the engine to stall unexpectedly while driving.

What to check

  • Ask whether the engine has ever stalled while driving, even once
  • With the engine idling, listen for the purge valve clicking irregularly
  • Check for a fuel smell around the filler cap, or a deformed tank
2 more steps in the write-up

Door latch: the latching component breaks and the door can open while driving

critical

A component inside the door latch breaks, so the latch no longer holds properly: the door is hard to close, or it only catches on the first detent. The driver and the passenger may believe the door is properly shut when it is not, and it can open while driving.

Show the rest

Ford issued five campaigns between 2015 and 2023, and two of them, 20V331000 and 23V775000, recalled cars where the earlier repair had not been carried out properly. The 2020 campaign names six models: the 2011-2014 Fiesta, the 2012-2015 Focus, the 2013-2015 C-Max, the 2014-2016 Transit Connect, the 2015 Mustang and the 2013-2014 Fusion. The factory repair fits a revised door latch.

What to check

  • Close all four doors with normal force: none should need slamming, and none should bounce back
  • Push each door half shut: it must hold on the first detent, with no play
  • Open and close each one from the outside and the inside, including the child locks at the rear
2 more steps in the write-up

expensive4

Injector copper washer: the soot blocks the turbo's oil filter

expensive

The copper washers under the injectors start to leak at around 100 000 kilometres, and sooty gas gets from the combustion chamber into the engine bay. The soot first collects in the injector sleeve and makes the seal worse there, and then it gets into the engine oil.

Show the rest

From there the path leads to the turbo. A fine gauze filter sits in the banjo bolt of the turbo's oil feed pipe, and the soot blocks it. Measured on such a car, the oil pressure at the turbo at idle was 0.8 bar, while the specified minimum is 2.3 bar; after the gauze was taken out it became 3.4 bar. With that much less oil the bearing of the turbo fails, and that typically happens above 130 000 kilometres.

The early signs are the smell of diesel in the cabin and black, oily deposits around the injectors on the engine cover.

The repair is not just the turbo, and that is the most important part of it. The oil feed pipe and its banjo bolts, the sump, the oil pick-up strainer, the oil filter housing and the oil cooler, the intercooler, the particulate filter with the exhaust and the vacuum pump of the brake system all have to be cleaned or replaced, and all the injector sleeves, seals and copper washers have to be replaced. If any of these is left out, the new turbo goes the same way.

above 100,000 km

What to check

  • Open the bonnet and look at the base of the injectors: a black, oily ring shows a leak
  • Look at the engine cover as well: the black, oily trace appears there too
  • Smell the cabin after a cold start: the smell of diesel points to the same thing
3 more steps in the write-up

MMT6 manual: worn shift mechanism, hard shifting when cold

expensive

The gearbox itself is reliable, but the shift mechanism wears noticeably between 100,000 and 150,000 km. Shifting becomes stiff, and it is most obvious when cold: the lever does not want to find its place, or the gear only goes in with force.

Show the rest

At high mileage the synchros on the first two gears wear out, and then the shift grates. The gearbox comes with a dual-mass flywheel, which is not the most durable part either.

between 100,000 and 150,000 km

What to check

  • Set off from cold: both first and second must engage without snagging
  • Stop and select reverse: it must not grate or need force
  • While rolling, change down into second: this is where worn synchros are audible
2 more steps in the write-up

IB6 manual: little oil, leaks, and the synchro noise that follows

expensive

The gearbox is light and compact and reliable, but the small oil quantity makes it sensitive to leaks: not much has to escape before the level becomes critical.

Show the rest

Most complaints about synchro noise actually come from this, from the low oil level rather than from the synchro itself. Beyond that the input shaft bearing can wear out and reverse can fail. Every version comes with a dual-mass flywheel, which is not the most durable part.

What to check

  • Look at the gearbox housing from underneath: fresh oil means a leak, and here that is the main cause
  • Ask when the oil level was last checked and whether it has ever been topped up
  • While rolling, change down into second and third: grating means worn synchros
2 more steps in the write-up

MTX75 manual: leaking seals, worn shafts

expensive

The gearbox itself is reliable and has two weak points. One is the input shaft bearing, which is short-lived, the other is the oil seals, which leak continuously.

Show the rest

The leak is the more dangerous one: any drop in the oil level wears the shafts and the gear rims, and that wear cannot be undone. Most versions come with a dual-mass flywheel, which is not the most durable part either.

What to check

  • Look at the bottom of the gearbox and where the driveshafts come out: fresh oil means a leak
  • Ask when the gearbox oil level was last checked, and ask for the invoice
  • At a steady speed, listen for noise: a worn input shaft bearing drones
2 more steps in the write-up

Checklist

Ford Focus 1.6 TDCi 115hp First Edition

First what you would check on any car. Then the faults of this model.

Before you buy

Checklist

The printed sheet starts with what you would check on any car. What you tick stays on this device only.

On every car

Ask the owner

Faults of this model

vinkodex.com · Before you buy it, see what can go wrong.

Official recall5 recallsShow

The manufacturer fixes these for free at a franchised dealer. Ask with the VIN whether it was done.

Most recent: 9 June 2026

26V369000FUEL SYSTEM, GASOLINE:STORAGE:EVAPORATIVE EMISSIONS:CANISTERFUEL SYSTEM, GASOLINE:STORAGE:EVAPORATIVE EMISSIONS:CANISTER9 June 2026 · NHTSA (USA)

Ford Motor Company (Ford) is recalling certain 2012-2018 Focus vehicles previously repaired incorrectly under recall number 18V735. The Canister Purge Valve (CPV) may malfunction, causing the engine to stall unexpectedly while driving.

Risk: An engine that stalls while driving increases the risk of a crash.

Remedy: Dealers will update the powertrain control module (PCM) software, free of charge. Owner notification letters were mailed July 29, 2026. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 26S40. Vehicle Identification Numbers (VINs) involved in this recall will become searchable on NHTSA.gov on July 6,2026.

The authority's notice

19V515000FUEL SYSTEM, GASOLINE:STORAGEFUEL SYSTEM, GASOLINE:STORAGE5 July 2019 · NHTSA (USA)

Ford Motor Company (Ford) is recalling certain 2012 and 2017 Focus vehicles equipped with 2.0L GDI gasoline engines and 2013-2014 Focus ST vehicles equipped with 2.0L GTDI engines, previously recalled under 18V-735. The affected vehicles did not have the Powertrain Control Module (PCM) updated as intended. Therefore, the Canister Purge Valve (CPV) may malfunction, possibly causing excessive vacuum in the fuel vapor management system.

Risk: The excessive vacuum may result in an engine stall while driving, without warning and without the ability to restart the vehicle, increasing the risk of a crash.

Remedy: Ford will notify owners, and dealers will reprogram the Powertrain Control Module. Dealers will also check for fault codes and replace the CPV as needed. If the CPV is replaced, dealers will inspect and replace the carbon canister, fuel tank and fuel delivery module as necessary. The recall began July 29, 2019. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 19S22.

The authority's notice

18V735000FUEL SYSTEM, GASOLINE:STORAGEFUEL SYSTEM, GASOLINE:STORAGE22 October 2018 · NHTSA (USA)

Ford Motor Company (Ford) is recalling certain 2012-2018 Ford Focus vehicles with a 2.0L GDI or 2.0L GTDI engine. The Canister Purge Valve (CPV) may malfunction, possibly causing excessive vacuum in fuel vapor management system.

Risk: The excessive vaccuum may result in an engine stall while driving, without warning and without the ability to restart the vehicle, increasing the risk of a crash.

Remedy: Ford will notify owners, and dealers will reprogram the Powertrain Control Module. Dealers will also check for fault codes and replace the CPV as needed. If the CPV is replaced, dealers will inspect and replace the carbon canister, fuel tank and fuel delivery module as necessary. The recall began August 19, 2019. Owners may contact Ford Customer service at 1-866-436-7332. Ford's number for this recall is 18S32. Note: Until the vehicle is serviced for this concern, owners are advised to keep the fuel tank at least halfway full.

The authority's notice

16V698000LATCHES/LOCKS/LINKAGES:HATCHBACK/LIFTGATE:LOCKLATCHES/LOCKS/LINKAGES:HATCHBACK/LIFTGATE:LOCK28 September 2016 · NHTSA (USA)

Ford Motor Company (Ford) is recalling certain model year 2013-2017 Ford Focus hatchback vehicles manufactured February 14, 2012, to August 26, 2016 and equipped with a manual transmission. The hatchback of the affected vehicles may be unlatched with a single press of the interior latch release button. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 206, "Door Locks and Door Retention Components."

Risk: With only a single press needed, the driver may accidently unlatch the hatchback, increasing the risk of injury to any unsecured passengers in the back.

Remedy: Ford will notify owners, and dealers will reprogram the Body Control Module with updated software, free of charge. The recall began February 10, 2017. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 16C13.

The authority's notice

13V335000EXTERIOR LIGHTINGEXTERIOR LIGHTING1 August 2013 · NHTSA (USA)

Ford is recalling certain model year 2012-2013 Focus BEV vehicles equipped with High Intensity Discharge (HID) headlights, manufactured September 15, 2011, through May 6, 2013; and model year 2013 Focus ST vehicles equipped with High Intensity Discharge (HID) headlights, manufactured February 16, 2012, through May 7, 2013. Due to a wiring incompatability, the front side marker lamps may not function. Thus, these vehicles fail to comply to the requirements of Federal Motor Vehicle Safety Standard (FMVSS) No. 108, "Lamps, Reflective Devices, and Associated Equipment."

Risk: Without the proper illumination of the side maker lamps, the vehicle may be less visible in night time conditions, increasing the risk of a crash.

Remedy: Ford will notify owners, and dealers will modify the headlamp assembly wiring, free of charge. The recall began on August 16, 2013. Owners may contact the Ford customer relationship center at 1-866-436-7332. Ford's recall number is 13C04.

The authority's notice

Engine and transmission

2 engines · 3 transmissions

T1DA · 1.6 TDCI

85 kW (116 HP) · diesel

IB6 · 6-speed manual

manual · 6 speed

Torque limit285 Nm
MakerFord/Getrag

We built the code from the model and the gear count. The factory sheet does not state it. More than one engine code is possible. The fault list shows the faults of each. More than one transmission is possible. The gear count does not tell them apart. The code is on the side of the transmission.

Variant data

What is in this version

Factory data

Trim
First Edition
Body
saloon
Fuel
diesel
Transmission
manual
Engine size
1560 cc
Power
85 kW (116 HP)
Drive
FWD
Production
2011–2014

Factory service interval

The manufacturer specifies this for this version. Of the mileage and the time, the one that comes first is the one that counts.

  • Air filter

    • 60,000 km or 4 years

  • Cabin (pollen) filter

    • 30,000 km or 2 years

  • Brake fluid change

    • first: 3 years, then 2 years(first change at 3 years, then every two years)

  • Fuel filter, diesel

    • 60,000 km or 2 years
All Mk3 versions

Information, not an expert opinion

We write the descriptions, and we put the source next to them. A person reviews them before they go out. They are still information, not a technical expert opinion.

  • A fault on the list does not mean the car you are looking at has it.
  • A fault missing from the list does not mean the model is fault-free. Write-ups are made model by model. Not all of them are done.
  • You decide whether to buy. This is no substitute for an inspection. That needs a workshop and a history check.
Details in the terms