vinkodex.

BMW Z4 Z4 Roadster 2.0i Introduction common faults.

2006–2009, convertible, petrol, 150 HP.

The fault list covers: N46B20 engine.

What you save stays on this device only. My saves

3 fault write-ups. All are important. 9 recalls.

If you know the year, pick it. Faults for other years drop out of the list.

Before you buy

Known faults

3 important faults

critical1

In these engines the water pump is not belt driven but has its own electric motor. It gains on fuel consumption, but it opens a new failure path: the pump or its electronics often simply stops with no warning. Measured in the official complaints, the typical mileage is 161,000 km (a tenth of the complaints already at 81,000, a tenth only above 257,000 km). So the common wisdom of "around 100,000 km" is early: most of the failures happen between 130,000 and 250,000 km.

Show the rest

With a belt driven pump the flow weakens gradually, here the circulation stops in an instant. In urban traffic the temperature crosses the limit within minutes, the cylinder head distorts, and the repair is an engine rebuild.

Replacing a still good pump at around 120,000 to 150,000 km costs less than repairing an overheated engine. If the replacement is already in the service book, the pump has already been changed.

between 81,000 and 257,000 km

What to check

  • Watch the coolant temperature gauge after startup: it should settle evenly, not jump around
  • Standing still with a warm engine, listen for whether the cooling fan and the pump are working
  • Ask for a fault code read: codes pointing at coolant flow belong here
2 more steps in the write-up

expensive2

VANOS adjusts the position of the camshaft with the pressure of the engine oil, and a solenoid valve metres that pressure. The valve sits in the oil circuit, and a fine filter screen protects the spool inside it from larger particles. That screen clogs with carbon and deposits: less oil flows through, and VANOS then adjusts late or does not move at all. The symptoms are a rough idle, rough running, a lack of torque at low revs and higher fuel consumption, because the valve timing is off. A short metallic clacking can also come on a cold start and goes quiet after 10 to 20 seconds. The engine warning light comes on with a camshaft fault code, and depending on the severity the engine control unit switches to limp mode. The fault code narrows down the cause. P0010 and P0013 typically mean the solenoid valve itself, that is a circuit fault or reduced oil flow through the clogged screen. P0011 and P0014 point more to a mechanical cause: a stretched timing chain or a worn adjuster. P0012 and P0015 report late camshaft control, whose common cause is slow pressure build-up at the adjuster, so again the dirty valve. The valve itself is a small part, between 50 and 120 euro, and with a clean screen cleaning is often enough; replacing the whole adjuster, by contrast, is a four-figure job. The reported repairs ran between 80 and 1,200 euro, depending on whether cleaning is enough and how many valves are affected. The main cause of the screen clogging is a stretched oil change interval and carbon-laden oil.

between 70,000 and 120,000 km80–1,200 EUR

What to check

  • Read the fault memory and note the exact code: P0010 and P0013 point to the valve
  • If P0011 or P0014 is stored, the timing chain has to be checked as well
  • Start the engine cold and listen for metallic clacking in the first 10 to 20 seconds
2 more steps in the write-up

The crankcase ventilation leads the gas that forms in the crankcase back to the intake and separates the oil out of it on the way. If the system clogs or the membrane tears, the pressure cannot get away: it finds a way out past the seals, or it pushes the oil through the piston rings. This is where the oil consumption comes from, and the oil that appears around the valve cover gasket. In the other direction a faulty breather takes unmetered air into the intake, and that is what makes the idle rough, the throttle response hesitant and the running coarse. Starting also gets harder, and in an extreme case the engine stalls at idle. Two characteristic signs help: weak or absent suction at the oil filler with the engine running, and noticeably rough running around 3,000 rpm. The hose at the rear of the valve cover can also let oil out. The sound insulation then soaks itself with oil, and oil gets everywhere in the engine bay. On the six-cylinder engines the breather is built into the valve cover, so the repair is replacing the cover or the whole oil separator together with the hoses, between 80 and 900 euro.

between 80,000 and 150,000 km80–900 EUR

What to check

  • With the engine running unscrew the oil filler cap: weak or absent suction is a sign
  • Look around the valve cover and at the rear of the engine bay for oil traces
  • Watch the idle, and the rough running around 3,000 rpm
2 more steps in the write-up

Checklist

BMW Z4 Z4 Roadster 2.0i Introduction

First what you would check on any car. Then the faults of this model.

Before you buy

Checklist

The printed sheet starts with what you would check on any car. What you tick stays on this device only.

On every car

Ask the owner

vinkodex.com · Before you buy it, see what can go wrong.

Official recall9 recallsShow

The manufacturer fixes these for free at a franchised dealer. Ask with the VIN whether it was done.

Most recent: 2 March 2022

22V119000ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CRANKCASE (PCV)ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CRANKCASE (PCV)2 March 2022 · NHTSA (USA)

BMW of North America, LLC (BMW) is recalling certain 2008-2013 1 Series Coupe (128i); 2007-2013 3 Series Coupe (328i, 328xi, 328i xDrive); 2007-2010 X3 SAV (X3 3.0si, X3 xDrive30i); 2008-2013 1 Series Convertible (128i); 2006-2011 3 Series Sedan (325i, 325xi, 328i, 328xi, 328i xDrive, 330i, 330xi); 2006-2012 3 Series Wagon (328i, 328i xDrive); 2007-2013 3 Series Convertible (328i); 2006-2010 5 Series Sedan (525i, 525xi, 528i, 528xi, 530i, 530xi); 2006-2007 5 Series Wagon (530xi); 2007-2010 X5 SAV (X5 3.0si, X5 xDrive30i); 2006-2008 Z4 Coupe (Z4 3.0si); and 2006-2011 Z4 Roadster (Z4 3.0i, Z4 3.0si, Z4 sDrive30i) vehicles. The heater for the positive crankcase ventilation (PCV) valve may short circuit.

Risk: An electrical short can cause the PCV valve heater to overheat, increasing the risk of a fire while driving or, soon after driving when parked.

Remedy: This recall supersedes and expands previous NHTSA recalls 17V-683 and 19V-273. Dealers will install an electrical wiring harness with fuse protection for the PCV Valve heater in potentially affected vehicles, free of charge. This recall supersedes and expands previous NHTSA recalls 17V-683 and 19V-273. Vehicles previously repaired under the prior recalls will need to come back for the new recall remedy. The remedy is currently being developed. Interim owner notification letters informing owners of the safety risk were mailed on April 1, 2022. Owner notification letters were mailed on July 22, 2022. Owners may contact BMW customer service at 1-800-525-7417.

We could not check this: model year. The authority's notice

19V273000ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CRANKCASE (PCV)ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CRANKCASE (PCV)4 April 2019 · NHTSA (USA)

BMW of North America, LLC (BMW) is recalling certain 2006 525i, 525xi, 530i, 530xi, 530xi Sports Wagon, 325i, 325xi, 325xi Sports Wagon, 330i, 330xi, Z4 3.0i and Z4 3.0si vehicles. The heater for the positive crankcase ventilation (PCV) valve may short circuit.

Risk: An electrical short can cause the parts within the PCV valve to melt, increasing the risk of a fire, even when the vehicle is not in use.

Remedy: BMW will notify owners, and dealers will replace the PCV valve heater, free of charge. The recall began May 30, 2019. Owners may contact BMW customer service at 1-800-525-7417. Note: This recall is an expansion to recall 17V-683.

We could not check this: model year. The authority's notice

17V683000ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CRANKCASE (PCV)ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CRANKCASE (PCV)30 October 2017 · NHTSA (USA)

BMW of North America, LLC (BMW) is recalling certain 2008-2011 128i and 2007-2011 328i, 328xi, 328i xDrive, 525i, 525xi, 528i, 528xi, 530i, 530xi, X3 3.0si, X3 xDrive30i, X5 xDrive30i, Z4 3.0i, Z4 3.0si and Z4 sDrive30i vehicles. The heater for the positive crankcase ventilation (PCV) valve may short circuit.

Risk: An electrical short can cause the parts within the PCV valve to melt, increasing the risk of a fire, even when the vehicle is not in use.

Remedy: BMW will notify owners, and dealers will replace the PCV valve heater, free of charge. Interim letters were mailed on November 27, 2017. Owners will receive a second notification by the end of October 2018. Owners may contact BMW customer service at 1-800-525-7417.

We could not check this: model year. The authority's notice

04V247000AIR BAGSAIR BAGS24 May 2004 · NHTSA (USA)

ON CERTAIN PASSENGER VEHICLES, INCOMPATIBLE ELECTRONIC AIR BAG SYSTEM PROCESSORS MAY HAVE BEEN INSTALLED.

Risk: IN THE EVENT OF A CRASH, AIR BAG DEPLOYMENT MAY NOT OCCUR, INCREASING THE RISK OF INJURIES TO THE DRIVER AND/OR FRONT PASSENGER.

Remedy: DEALERS WILL INSPECT AND, IF NECESSARY, REPLACE THE AIR BAG SYSTEM PROCESSORS. THE RECALL BEGAN JUNE 11, 2004. OWNERS SHOULD CONTACT BMW AT 1-800-831-1117.

We could not check this: model year. The authority's notice

04V182000FUEL SYSTEM, GASOLINE:DELIVERY:FUEL PUMPFUEL SYSTEM, GASOLINE:DELIVERY:FUEL PUMP12 April 2004 · NHTSA (USA)

ON CERTAIN PASSENGER VEHICLES, UNDER CERTAIN ENVIRONMENTAL CONDITIONS, A VAPOR LOCK IN THE FUEL PUMP COULD OCCUR CAUSING THE ENGINE TO STALL. IF THIS WERE TO HAPPEN, THE ENGINE WOULD NOT BE ABLE TO BE RESTARTED FOR APPROXIMATELY 15 TO 20 MINUTES.

Risk: IF STALLING WERE TO OCCUR, THE DRIVER WOULD BE UNABLE TO MAINTAIN VEHICLE SPEED OR ACCELERATE, INCREASING THE RISK OF A CRASH.

Remedy: DEALERS WILL INSTALL A RESISTOR IN THE ELECTRICAL LINE POWERING THE FUEL PUMP IN ORDER TO PREVENT AN OCCURRENCE OF VAPOR LOCK. THE RECALL BEGAN MAY 11, 2004. OWNERS SHOULD CONTACT BMW AT 1-800-831-1117.

We could not check this: model year. The authority's notice

03V214000TIRESTIRES9 June 2003 · NHTSA (USA)

ON CERTAIN VEHICLES EQUIPPED WITH 18" TIRES, IT IS POSSIBLE THAT THE TIRE HAS BEEN DAMAGED DURING THE MOUNTING PROCESS TO THE RIM.

Risk: CONSEQUENTLY, A LOSS OF TIRE PRESSURE, OR A TIRE FAILURE, COULD OCCUR. DEPENDING ON TRAFFIC CONDITIONS AND THE DRIVER'S REACTIONS, THIS COULD LEAD TO A CRASH.

Remedy: DEALERS WILL UNSEAT THE TIRE FROM ITS RIM, INSPECT FOR ANY DAMAGE, AND THEN RESEAT THE TIRE TO ITS RIM. IF INSPECTION REVEALS THAT A FRONT TIRE HAS INCURRED DAMAGE DURING THE MOUNTING PROCESS, IT WILL BE REPLACED. OWNER NOTIFICATION BEGAN JULY 14, 2003. OWNERS SHOULD CONTACT BMW AT 1-800-831-1117.

We could not check this: model year. The authority's notice

03V032000SEAT BELTS:FRONT:BUCKLE ASSEMBLYSEAT BELTS:FRONT:BUCKLE ASSEMBLY4 February 2003 · NHTSA (USA)

ON CERTAIN PASSENGER VEHICLES, THE CONNECTION OF THE SAFETY BELT BUCKLE TO THE STEEL ROPE OF THE TENSIONER DOES NOT MEET BMW SPECIFICATIONS. IN SEVERE FRONTAL CRASHES, THIS CONNECTION CAN DETACH.

Risk: IF THE CONNECTION DETACHES, THE PROTECTION PROVIDED BY THE SAFETY BELT IS LIKELY TO BE IMPAIRED, AND SERIOUS INJURIES TO THE DRIVER AND/OR FRONT PASSENGER COULD OCCUR THAT MIGHT OTHERWISE BE MITIGATED.

Remedy: DEALERS WILL INSPECT BOTH FRONT SAFETY BELT TENSIONER AND BUCKLE ASSEMBLIES, AND IF NECESSARY, REPLACE THESE PARTS. OWNER NOTIFICATION BEGAN MARCH 19, 2003. OWNERS WHO TAKE THEIR VEHICLES TO AN AUTHORIZED DEALER ON AN AGREED UPON SERVICE DATE AND DO NOT RECEIVE THE FREE REMEDY WITHIN A REASONABLE TIME SHOULD CONTACT BMW AT 1-800-831-1117.

We could not check this: model year. The authority's notice

A12/00039/20Safety recallInjuriesno date · EU Safety Gate

The connector of the positive battery cable on the front power distribution box may be damaged over the lifetime of the vehicle by vibrations and currents. This may lead to failure of the engine and of the vehicle's electrical system, including headlights and occupant protection which will increase the risk of an accident and injuries to the occupants.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

We could not check this: model year. The authority's notice

A12/1019/18Safety recallInjuriesno date · EU Safety Gate

The plug connection for the positive battery cable may be defective. This could cause the vehicle electrics and the engine to fail while the vehicle is in motion.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

We could not check this: model year. The authority's notice

Engine and transmission

N46B20 · 2.0i/xDrive20i

95–110 kW (129–150 HP) · petrol

We built the code from the model and the gear count. The factory sheet does not state it.

Variant data

What is in this version

Factory data

Trim
Z4 Roadster 2.0i Introduction
Body
convertible
Fuel
petrol
Transmission
manual
Engine size
1995 cc
Power
110 kW (150 HP)
Drive
RWD
Production
2006–2009

Factory service interval

The manufacturer specifies this for this version. Of the mileage and the time, the one that comes first is the one that counts.

  • Air filter

    • 60,000 km or 4 years
  • Cabin (pollen) filter

    • 30,000 km or 2 years
  • Brake fluid change

    • first: 3 years, then 2 years(first change at 3 years, then every two years)
  • Engine oil and oil filter (BMW condition-based service)

    • LongLife25,000 km or 2 years
  • Spark plugs, petrol

    • 60,000 km or 6 years

Information, not an expert opinion

We write the descriptions, and we put the source next to them. A person reviews them before they go out. They are still information, not a technical expert opinion.

  • A fault on the list does not mean the car you are looking at has it.
  • A fault missing from the list does not mean the model is fault-free. Write-ups are made model by model. Not all of them are done.
  • You decide whether to buy. This is no substitute for an inspection. That needs a workshop and a history check.
Details in the terms