vinkodex.

BMW X3 X3 40d xDrive common faults.

2024–, SUV, diesel, 303 HP.

The fault list covers: N57D30 engine, ZF8HP70 transmission.

What you save stays on this device only. My saves

6 fault write-ups. All are important. 54 recalls.

If you know the year, pick it. Faults for other years drop out of the list.

Before you buy

Known faults

6 important faults

critical3

Diesel high pressure pump: power loss and engine shutdown while driving

critical

The high pressure pump of these common rail diesels (Bosch CP4) can fail while driving. The characteristic course is not gradual: a "Drivetrain fault" message appears on the dash, and within a few seconds the power is gone, on the motorway too. Afterwards the engine often cranks but will not start.

Show the rest

What makes the repair expensive: once the inside of the pump wears, metal debris travels through the rail and contaminates the entire fuel system. At that point replacing the pump is not enough: the injectors, the rails, the tank and the lines go with it. That is the difference between a "pump replacement" and a "full system replacement" quote, that is what you should ask about.

The maker started a recall for this in the United States (NHTSA 21V586000, 2014 to 2018 328d / X5 xDrive35d / 535d / 740Ld / X3 xDrive28d). The same campaign did not run in Europe, even though the same pump works in the 320d/520d/X3 20d versions that are common right across Europe. The recall does not cover these cars.

between 79,000 and 248,000 km

What to check

  • Ask whether there has ever been a "Drivetrain fault" message or a loss of power while driving
  • Ask for the service history: if the high pressure pump was replaced, check whether the injectors and the lines were replaced with it. If not, the debris may still be in the system
  • After a cold start listen to the engine at idle: irregular running or smoke is suspect
3 more steps in the write-up

N47 / N57 diesel: timing chain on the rear of the engine

critical

In these diesels BMW put the timing chain at the back of the engine, on the gearbox side. The chain, the guides and the tensioner wear early. The symptom is a metallic rattle on a cold start that quietens once warm.

Show the rest

The engine or the gearbox has to come out for the replacement, so the labour is a multiple of the parts cost. If the chain breaks or jumps, the engine is badly damaged inside, and the repair is an engine rebuild.

The problem is worst on engines built between March 2007 and March 2011, and the ones before early 2009 are the worst of all. The maker handled it under a service campaign in several European markets, but in the United Kingdom there was no formal recall. "It was never recalled" does not mean the chain is fine.

According to the German technical press the fault affects the whole N47 series and every power output, inspection is advised from 100,000 km, and factory revisions closed the matter around 2013, so cars built after 2013 are in a significantly better position. Stretching is typically preceded by a distinct rattle.

between 100,000 and 200,000 km

What to check

  • Insist on a cold start: the car should stand overnight, and the seller must not start it before you arrive
  • At the moment of starting, stand behind the engine (on the gearbox side) and listen to the first 3 to 5 seconds
  • A metallic rattle from the back of the engine calls for immediate expert inspection: this is not "diesel noise"
2 more steps in the write-up

Diesel EGR cooler: cracking, coolant in the intake, fire risk

critical

The internal fins of the exhaust gas recirculation cooler crack over time, and glycol coolant leaks into the intake, where it mixes with soot. The sticky mixture can ignite at high temperature: it can melt the plastic intake manifold and, in extreme cases, cause an engine bay fire.

Show the rest

The maker recalled the 2013 to 2018 four and six cylinder diesels, roughly 800,000 cars worldwide. The first repair attempt proved insufficient, and the leak returned in several cases: the cooler fitted since 2022, from a different supplier, is the valid fix.

So "the recall was carried out" is not enough on its own: you have to check when, and which repair was done. A first round repair does not by itself rule the problem out.

The early symptoms are white, sweet smelling exhaust smoke, slowly dropping coolant, and a rough idle.

It shows up on diesels built between 2013 and 2018. The earlier M57 is not covered by the recall.

between 108,000 and 222,000 km

What to check

  • Check the level in the expansion tank, and ask whether it has needed topping up
  • After a cold start watch the exhaust: persistent white smoke and a sweet smell mean the coolant is burning
  • Ask for the service book and find the EGR cooler recall entry: Check the date too
2 more steps in the write-up

expensive3

XDrive transfer case (ATC): binding in corners, plastic actuator gear

expensive

The heart of the four wheel drive in the longitudinal engine BMW X models (X3, X5 and the X1 E84) is the ATC transfer case. It has two faults, and you can feel both while driving.

Show the rest

The first is wear of the clutch pack and the fluid: in a slow, tight corner (a car park, a roundabout) the car jerks and "hops", as if the drive grabbed and let go. You can also get a jerk when pulling away on a slope. The second is the plastic actuator gear: the position signal is lost, the brake, ABS and 4x4/DSC lights come on together on the dash, and a clicking is audible from the transfer case when you switch the ignition off.

Workshops often propose a full transfer case replacement straight away. But the plastic gear can be replaced on its own, and the wrong tyre size or a mixed set of tyres also imitates the jerking, because the transfer case then slips continuously. So clear up the tyres and the fault code first, before you pay for a transfer case replacement.

between 72,000 and 175,000 km

What to check

  • In a slow, tight corner (a car park) watch for jerking, binding and a "skipping" feel
  • When pulling away on light throttle, can you feel the drivetrain jerk
  • Watch the dash: 4x4, ABS, DSC and brake lights together point at the actuator
4 more steps in the write-up

ZF 8HP automatic: mechatronics unit and connector sleeve leak

expensive

The ZF eight speed automatic (BMW Steptronic 8HP family) has two faults, and you can feel both.

Show the rest

The first is the mechatronics unit: the valve body and the control electronics in one. If the solenoids or the pressure regulation weaken, the gearbox jerks, the D/R engagement is delayed, it logs a gear ratio fault code, and finally drops into limp mode (often staying in 2nd or 3rd).

The second, and often misdiagnosed, is the connector sleeve of the mechatronics unit: the O-ring of the plastic sleeve ages, and ATF leaks from the side of the housing, exactly where the wiring harness enters. This is easy to mistake for a rear crankshaft seal. The trail starts from the driver's side of the housing, not from the clutch side.

On cars built in 2023 there was also a separate safety recall for a welding fault in the mechatronics unit. That is not the same as the wear related sleeve and the valves.

Check the fluid level, the area around the sleeve and the fault codes first; do not accept a "full gearbox replacement" quote straight away.

above 120,000 km

What to check

  • On the test drive watch for delayed D/R engagement, a jerk when shifting, and limp mode (a stuck gear)
  • Look at the driver's side of the gearbox housing where the wiring harness enters: an ATF trail from the sleeve is suspect
  • Do not confuse it with a rear crankshaft seal leak: the direction of the trail decides
3 more steps in the write-up

Undersized oil pump: lubrication runs out at the main and rod bearings

expensive

The connecting rod and main bearings run out, and the cause is the factory oil pump: it is undersized and does not deliver enough oil volume at idle and at low revs. BMW specifies 1.2 bar of oil pressure at idle at operating temperature, but on engines with mileage it falls below that, and the bearing shell is no longer adequately lubricated with that much. Bearing damage is reported between 130 000 and 200 000 kilometres, but it is always preceded by a longer period with low oil pressure.

Show the rest

The most important thing to know is that the control unit does not signal this: no lamp comes on for low oil pressure, and no fault code is stored either. The symptom is a quiet ticking at idle and a metallic noise under load, and at the rod bearing this is often explained by something else. It can be measured, though: a workshop connects a gauge and reads the real pressure at idle at operating temperature, and below 1.2 bar the engine is running in the period that causes the damage.

The length of the oil change decides matters on this engine. A change between 10 000 and 20 000 kilometres protects the bearing, the long factory interval does not. If the main bearing turns, the crankshaft is damaged too, and the upper half of the main bearing bed is aluminium while the lower is steel, so repairing the crankcase is difficult, and the block often goes out cracked and beyond repair. As prevention an uprated oil pump exists, with larger gears and its own pressure regulator, between 800 and 1150 euros, without fitting.

between 130,000 and 200,000 km

What to check

  • Have the oil pressure measured with a gauge at operating temperature at idle: below 1.2 bar is dangerous
  • Do not wait for a lamp or a fault code: the control unit does not signal this fault
  • Listen to the engine warm: a quiet ticking at idle, a metallic noise under load
3 more steps in the write-up

Checklist

BMW X3 X3 40d xDrive

First what you would check on any car. Then the faults of this model.

Before you buy

Checklist

The printed sheet starts with what you would check on any car. What you tick stays on this device only.

On every car

Ask the owner

Faults of this model

vinkodex.com · Before you buy it, see what can go wrong.

Official recall54 recallsShow

The manufacturer fixes these for free at a franchised dealer. Ask with the VIN whether it was done.

Most recent: 12 August 2026

26V524000STEERING:LINKAGES:KNUCKLE:SPINDLE:ARMSTEERING:LINKAGES:KNUCKLE:SPINDLE:ARM12 August 2026 · NHTSA (USA)

BMW of North America, LLC (BMW) is recalling certain 2024-2026 X3 sDrive30i, X3 30 xDrive, and X3 M50 xDrive vehicles. The steering spindle may have been incorrectly attached to the steering column.

Risk: An incorrectly attached steering spindle can lead to a loss of steering control, increasing the risk of a crash.

Remedy: Dealers will inspect the steering connection and replace hardware or replace the spindle and column, as necessary, free of charge. Owner notification letters were mailed October 8, 2026. Owners may contact BMW customer service at 1-800-525-7417. Vehicle Identification Numbers (VINs) involved in this recall will become searchable on NHTSA.gov beginning October 2, 2026.

We could not check this: model year. The authority's notice

SR/02180/26Safety recallFire7 July 2026 · EU Safety Gate

The RSW22 starter with reinforced water tightness (RWT) may experience increased abrasion of the magnetic contact, causing deposits to build up at the lowest point inside the relay. These deposits may increase relay contact resistance, leading to starting failures or short circuits. If a short circuit occurs, either when attempting to start the vehicle or while driving due to vibration-related movement of the deposits, it could cause a thermal event and increase the risk of fire. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: 07/07/2026

We could not check this: model year. The authority's notice

SR/00551/26Safety recallFire30 January 2026 · EU Safety Gate

The failure concerns the RSW22 starter, type RWT (reinforced for watertightness). Increased abrasion of the magnetic contact can lead to the formation of deposits at the lowest point of the relay interior. This in turn can increase the resistance of the relay contact, causing accidental ignition or even short circuits, possibly leading to a thermal reaction and fire. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: 30/01/2026

We could not check this: model year. The authority's notice

SR/00568/26Safety recallFire30 January 2026 · EU Safety Gate

The failure concerns the RSW22 starter, type RWT (reinforced for watertightness). Increased abrasion of the magnetic contact can lead to the formation of deposits at the lowest point of the relay interior. This in turn can increase the resistance of the relay contact, causing accidental ignition or even short circuits, possibly leading to a thermal reaction and fire. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: 30/01/2026

We could not check this: model year. The authority's notice

SR/00584/26Safety recallFire30 January 2026 · EU Safety Gate

The failure concerns the RSW22 starter, type RWT (reinforced for watertightness). Increased abrasion of the magnetic contact can lead to the formation of deposits at the lowest point of the relay interior. This in turn can increase the resistance of the relay contact, causing accidental ignition or even short circuits, possibly leading to a thermal reaction and fire. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: 30/01/2026

We could not check this: model year. The authority's notice

25V857000STEERING:STEERING CONTROL MODULESTEERING:STEERING CONTROL MODULE11 December 2025 · NHTSA (USA)

BMW of North America, LLC is recalling certain 2025-2026 X3 vehicles. While the vehicle is stationary, unexpected steering wheel movement (rotation) may occur.

Risk: Unintended steering wheel movement while the vehicle is stationary increases the risk of an injury and on the road, a crash.

Remedy: The steering system software will be updated, free of charge, either over-the-air (OTA) or by a dealer. Owner notification letters were mailed February 6, 2026. Owners may contact BMW customer service at 1-800-525-7417. Vehicle Identification Numbers (VINs) involved in this recall will be searchable on NHTSA.gov beginning February 2, 2026.

We could not check this: model year. The authority's notice

25V247000SERVICE BRAKES, HYDRAULIC:FOUNDATION COMPONENTS:DISCSERVICE BRAKES, HYDRAULIC:FOUNDATION COMPONENTS:DISC16 April 2025 · NHTSA (USA)

BMW of North America, LLC (BMW) is recalling certain 2025 X3 30 xDrive vehicles. The front brake discs may have been damaged during transport before they were installed on the vehicle.

Risk: Damaged front brakes may not function properly, increasing the risk of a crash.

Remedy: Dealers will replace the front brake discs and brake pads, free of charge. Owner notification letters are expected to be mailed June 6, 2025. Owners may contact BMW customer service at 1-800-525-7417.

We could not check this: model year. The authority's notice

25V202000ELECTRICAL SYSTEM:STARTER ASSEMBLYELECTRICAL SYSTEM:STARTER ASSEMBLY1 April 2025 · NHTSA (USA)

BMW of North America, LLC (BMW) is recalling certain 2025 330i, 330i xDrive, 530i, 530i xDrive, 4 Series Coupe (430i, 430i xDrive), 4 Series Convertible (430i, 430i xDrive), 4 Series Gran Coupe (430i, 430i xDrive) and X3 30 xDrive vehicles. The electrical connection between the starter-generator and battery may come loose.

Risk: A loose starter-generator connection can result in an engine stall, increasing the risk of a crash. In addition, the wiring may overheat, increasing the risk of a fire.

Remedy: Dealers will inspect and replace the starter-generator and positive battery cable as necessary, free of charge. Interim owner letters notifying owners of the safety risk were mailed May 28, 2025. Second letters will be sent once the remedy is available. Owners may contact BMW customer service at 1-800-525-7417.

We could not check this: model year. The authority's notice

25V154000SERVICE BRAKES, HYDRAULIC:FOUNDATION COMPONENTS:HOSES, LINES/PIPING, AND FITTINGSSERVICE BRAKES, HYDRAULIC:FOUNDATION COMPONENTS:HOSES, LINES/PIPING, AND FITTINGS12 March 2025 · NHTSA (USA)

BMW of North America, LLC (BMW) is recalling certain 2025 X3 30 xDrive and X3 M50 xDrive vehicles. The rear brake hoses may leak, causing a loss of rear brake function, and a loss of the Antilock Brake System (ABS) and the Dynamic Stability Control (DSC) system.

Risk: A loss of rear brake function increases the risk of a crash.

Remedy: Dealers will replace the rear brake hoses, free of charge. Owner notification letters were mailed May 9, 2025. Owners may contact BMW customer service at 800-525-7417.

We could not check this: model year. The authority's notice

25V109000ELECTRICAL SYSTEM:12V/24V/48V BATTERY:CABLESELECTRICAL SYSTEM:12V/24V/48V BATTERY:CABLES21 February 2025 · NHTSA (USA)

BMW of North America, LLC (BMW) is recalling certain 2025 X3 30 xDrive vehicles. The connection between the positive battery cable and the starter-generator may have been improperly tightened and overheat.

Risk: An overheated battery cable connection can cause an engine stall and increase the risk of a crash. In addition, an overheated battery cable increases the risk of a fire.

Remedy: Dealers will inspect and tighten the connection between the positive battery cable and the starter-generator, or replace the positive battery cable and starter-generator if necessary, free of charge. Owner notification letters were mailed June 5, 2025. Owners may contact BMW customer service at 800-525-7417.

We could not check this: model year. The authority's notice

25V106000LATCHES/LOCKS/LINKAGES:DOORS:LOCKLATCHES/LOCKS/LINKAGES:DOORS:LOCK20 February 2025 · NHTSA (USA)

BMW of North America, LLC (BMW) is recalling certain 2022-2024 X3 sDrive30i and X3 xDrive30i vehicles. The second-row seat side door locking modules may not function properly and allow the doors to be unlocked with a single motion. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 206, "Door Locks and Door Retention Components."

Risk: Doors that can be inadvertently unlocked and unlatched may open unexpectedly, increasing the risk of injury to rear seat occupants.

Remedy: Dealers will replace the second-row seat side door locking modules, free of charge. A letter informing owners of the safety risk was mailed on April 21, 2025. Owners may contact BMW customer service at 800-525-7417.

We could not check this: model year. The authority's notice

24V909000SUSPENSION:FRONT:WHEEL BEARINGSUSPENSION:FRONT:WHEEL BEARING5 December 2024 · NHTSA (USA)

BMW of North America, LLC (BMW) is recalling certain 2025 X3 30 vehicles. The front wheel left-side swivel bearing may crack, causing a loss of vehicle handling and control.

Risk: A loss of vehicle handling and control increases the risk of a crash.

Remedy: Dealers will replace the front left-side swivel bearing, free of charge. One owner was contacted December 12, 2024. Owners may contact BMW customer service at 1-800-525-7417.

We could not check this: model year. The authority's notice

24V856000AIR BAGS:SIDE/WINDOW:CURTAINAIR BAGS:SIDE/WINDOW:CURTAIN12 November 2024 · NHTSA (USA)

BMW of North America, LLC (BMW) is recalling certain 2025 X3 30 xDrive vehicles. The gas generator in the right-side head curtain air bag may have been assembled incorrectly.

Risk: An incorrectly assembled air bag can result in delayed activation or improper deployment of the head curtain air bag, increasing the risk of injury in a crash.

Remedy: Dealers will inspect and replace the right-side head curtain air bag, if necessary, free of charge. The vehicles have not been sold from dealer inventory and therefore no owner letters will be mailed. Owners may contact BMW customer service at 1-800-525-7417.

We could not check this: model year. The authority's notice

24V772000AIR BAGS:PASSENGER SIDE FRONTAL:CUSHIONAIR BAGS:PASSENGER SIDE FRONTAL:CUSHION17 October 2024 · NHTSA (USA)

BMW of North America, LLC (BMW) is recalling certain 2025 X3 xDrive30i and X3 M50i vehicles. The front passenger air bag fabric may have been damaged during transport between suppliers.

Risk: A damaged air bag may not inflate properly, increasing the risk of injury in a crash.

Remedy: Dealers will replace the front passenger air bag, free of charge. None of the affected vehicles have been sold yet and therefore no owner notification letters will be mailed. Owners may contact BMW customer service at 1-800-525-7417.

We could not check this: model year. The authority's notice

24V764000STRUCTURESTRUCTURE15 October 2024 · NHTSA (USA)

BMW of North America, LLC (BMW) is recalling certain 2018-2022 X3 sDrive30i, X3 xDrive30i, X3 M40i, and X3 M vehicles. The attachment for the rear cargo rail may become damaged in a rear crash and result in the cargo rail detaching.

Risk: Interior rear cargo rail detachment during a crash can increase the risk of injury.

Remedy: Dealers will replace the rear cargo rail attachment bolts, free of charge. Owner notification letters were mailed December 12, 2024. Owners may contact BMW customer service at 1-800-525-7417. Vehicles in this recall were previously remedied for this issue under recall number 24V-534 and will need to have the new repair completed.

We could not check this: model year. The authority's notice

24V534000STRUCTURESTRUCTURE17 July 2024 · NHTSA (USA)

BMW of North America, LLC (BMW) is recalling certain 2018-2023 X3 sDrive30i, X3 xDrive30i, X3 M40i, and X3 M vehicles. The attachment for the interior cargo rail may become damaged in a rear crash and result in the cargo rail detaching.

Risk: Interior cargo rail detachment during a rear crash can increase the risk of injury.

Remedy: Dealers will replace the rear cargo rail attachment bolts, free of charge. Owner notification letters were mailed January 2, 2024. Owners may contact BMW customer service at 1-800-525-7417.

We could not check this: model year. The authority's notice

22V513000FUEL SYSTEM, GASOLINE:FUEL INJECTION SYSTEM:FUEL RAILFUEL SYSTEM, GASOLINE:FUEL INJECTION SYSTEM:FUEL RAIL20 July 2022 · NHTSA (USA)

BMW of North America, LLC (BMW) is recalling certain 2022 X1 xDrive 28i, X3 xDrive30i, and 228i Gran Coupe vehicles. The high-pressure fuel rail may crack and result in a fuel leak within the engine compartment.

Risk: A fuel leak in the presence of an ignition source increases the risk of a fire.

Remedy: Dealers will replace the high-pressure fuel rail, free of charge. Owner notification letters were mailed September 19, 2022. Owners may contact BMW customer service at 1-800-525-7417.

We could not check this: model year. The authority's notice

A12/01930/23Safety recallInjuries29 June 2021 · EU Safety Gate

The propellant in the driver airbag can deteriorate due to high humidity and temperature variations. In the event of an accident in which the airbag deploys, this could result in fragments from the inflator casing coming loose and injuring the vehicle’s occupants. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: 29/06/2021

We could not check this: model year. The authority's notice

20V443000BACK OVER PREVENTION: SENSING SYSTEM: CAMERABACK OVER PREVENTION: SENSING SYSTEM: CAMERA29 July 2020 · NHTSA (USA)

BMW of North America, LLC (BMW) is recalling certain 2020 X3 sDrive40i, X3 xDrive40i and X3M40i vehicles. These vehicles were not programmed with rearview camera software during assembly, therefore, when the transmission is shifted to reverse, a rearview image is not displayed. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard number 111, "Rearview Mirrors."

Risk: An inoperative rearview camera display can increase the risk of a crash when reversing.

Remedy: BMW will notify owners, and dealers will program the affected vehicles with rearview camera software, free of charge. The recall began August 14, 2020. All vehicles have been remedied as of November 9, 2020. Owners may contact BMW customer service at 1-800-525-7417.

We could not check this: model year. The authority's notice

18V431000EXTERIOR LIGHTING:TURN SIGNALEXTERIOR LIGHTING:TURN SIGNAL21 June 2018 · NHTSA (USA)

BMW of North America, LLC (BMW) is recalling certain 2018 BMW X3 xDrive30i and X3 M40i vehicles. The rear turn signals on the outboard side panel will illuminate red, while the inboard turn signals simultaneously illuminate amber. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 108, "Lamps, Reflective Devices, and Associated Equipment."

Risk: Turn signals that flash multiple colors may confuse other drivers, increasing the risk of a crash.

Remedy: BMW will notify owners, and dealers will inspect the rear turn signal lights, and replace if necessary, free of charge. The recall began August 20, 2018. Owners may contact BMW customer service at 1-800-525-7417.

We could not check this: model year. The authority's notice

18V374000LANE DEPARTURE: LANE KEEP: STEERING ASSISTLANE DEPARTURE: LANE KEEP: STEERING ASSIST6 June 2018 · NHTSA (USA)

BMW of North America, LLC (BMW) is recalling certain 2018-2019 BMW X3 xDrive30i, X3 sDrive30i, and X3 M40i vehicles equipped with the "Active Lane Keeping Assistant" option. The steering wheel may be incompatible with the lane keeping assistant function and may not detect if the driver's hands are off the wheel.

Risk: If the sensors do not properly detect the driver's hands are off the wheel, the driver may not be alerted by one or more warning signals, increasing the risk of a crash.

Remedy: BMW will notify owners, and dealers will inspect the steering wheel, replacing it if necessary, free of charge. The recall began on July 19, 2018. Owners may contact BMW customer service at 1-800-525-7417.

We could not check this: model year. The authority's notice

18V154000STRUCTURE:BODYSTRUCTURE:BODY7 March 2018 · NHTSA (USA)

BMW of North America, LLC (BMW) is recalling certain 2018 BMW X3 xDrive30i and X3 M40i vehicles. The rear spoiler may not have been properly attached during assembly, or may be missing screws, possibly causing the spoiler to detach while driving.

Risk: If the spoiler detaches while driving, it can become a road hazard, increasing the risk of a crash.

Remedy: BMW will notify owners, and dealers will inspect the spoiler, correcting its attachment as necessary, free of charge. The recall is expected to begin May 1, 2018. Owners may contact BMW customer service at 1-800-525-7417.

We could not check this: model year. The authority's notice

17V719000ELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANELELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANEL15 November 2017 · NHTSA (USA)

BMW of North America, LLC (BMW) is recalling certain 2018 230i, 230i xDrive, M240i, M240i xDrive, M2, and X3 xDrive 30i SAV vehicles. These vehicles may have an error in the software for the instrument panel, causing the display to not properly illuminate. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 101, "Control and Displays."

Risk: If the display does not illuminate during start up or does not illuminate various control and warning symbols while driving, it can increase the risk of a crash.

Remedy: BMW will notify owners, and dealers will update the instrument cluster display software, free of charge. The recall is expected to begin January 8, 2018. Owners may contact BMW customer service at 1-800-525-7417.

We could not check this: model year. The authority's notice

16V704000STEERING:ELECTRIC POWER ASSIST SYSTEMSTEERING:ELECTRIC POWER ASSIST SYSTEM3 October 2016 · NHTSA (USA)

BMW of North America, LLC (BMW) is recalling one model year 2017 BMW X3 xDrive 28i vehicle manufactured on June 7, 2016. This vehicle has electronic power steering (EPS), and the contact pins on the EPS control unit may not have been welded properly resulting in increased resistance.

Risk: An increase in pin contact resistance can increase the risk of a fire, even while the vehicle is parked and ignition is off.

Remedy: The vehicle was repaired at the dealership before sale. Therefore, an owner notification notice will not be issued for this campaign. Owners may contact BMW customer service at 1-800-525-7417.

We could not check this: model year. The authority's notice

A12/00068/19Safety recallInjuriesno date · EU Safety Gate

The press-in force of the counterbalance shaft’s bearing shells may not have met the specifications, which could cause the counterbalance shaft to become loose. As a result, the engine could be damaged and locked in motion, increasing the risk of an accident.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

We could not check this: model year. The authority's notice

A12/0013/19Safety recallInjuriesno date · EU Safety Gate

The screw connection on the steering spindle may not have been sufficiently tightened. The screw connection may consequently detach, leading to a loss of steering.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

We could not check this: model year. The authority's notice

A12/00184/24Safety recallInjuriesno date · EU Safety Gate

Due to a manufacturing error, the weld seam of the integrated transmission control unit (ITCU) may not have been correctly executed. As a result, transmission oil could leak into the ITCU, causing it to fail. This may lead to transmission seizure, increasing the risk of an accident. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

We could not check this: model year. The authority's notice

A12/00600/21Safety recallInjuriesno date · EU Safety Gate

A battery insert (crash pad) has not been fitted. As a result, the battery would not be adequately secured tn the event of an accident, which could cause certain certain safety functions to become unavailable.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

We could not check this: model year. The authority's notice

A12/00608/20Safety recallInjuriesno date · EU Safety Gate

The screw connection from the passenger's airbag to the instrument panel may not have been manufactured according to specifications. As a result, if the airbag is activated, the panel cover may break into pieces, which will be propelled against the passenger increasing the risk of injury.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

We could not check this: model year. The authority's notice

A12/00636/20Safety recallInjuriesno date · EU Safety Gate

The cable connecting the hall sensor with the seat buckle might be too short. Consequently, the sensor might detach from the buckle, causing a faulty seatbelt lock recognition, impairing the functioning of the restraint system and the deployment of the airbag, increasing the risk of injury in the event of an accident.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

We could not check this: model year. The authority's notice

A12/00988/23Safety recallInjuriesno date · EU Safety Gate

The driver's and/or passenger's seat could break the frame rail that connects the seat to the guide rails on the vehicle floor. The stability of the seats may be affected, increasing the risk of injury in case of an accident. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

We could not check this: model year. The authority's notice

A12/01342/20Safety recallFireno date · EU Safety Gate

A short circuit in the high-voltage battery could occur during initial charging due to a particle in the form of a welding bead. This may trigger a chain reaction in the battery, increasing the risk of fire.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

We could not check this: model year. The authority's notice

A12/01377/22Safety recallFireno date · EU Safety Gate

Defects in the winding of cell-internal foils in the high-voltage batteries can lead to the occurrence of increased self-discharge. This can cause high voltage cell modules to overheat, increasing the risk of fire. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

We could not check this: model year. The authority's notice

A12/01665/23Safety recallFire, Injuriesno date · EU Safety Gate

The starter generator cable is not properly bolted to the bodywork. This may lead to engine shut-off while the vehicle is moving, creating a risk of injuries. In addition, an increase in the contact resistance may cause local heating of the bolt connection and lead to a fire. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

We could not check this: model year. The authority's notice

A12/01667/23Safety recallFire, Injuriesno date · EU Safety Gate

A faulty ground cable of the starter generator can cause the engine to stop while the vehicle is in motion, creating a risk of an accident. Moreover, increased contact resistance can cause local heating of the screw connection, increasing the risk of fire. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

We could not check this: model year. The authority's notice

A12/01824/20Safety recallInjuriesno date · EU Safety Gate

The safety belts for the driver and passenger seats may not have been fully bolted on. As a consequence, their restraining effect is not ensured in the event of an accident, increasing the risk of injury.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

We could not check this: model year. The authority's notice

A12/02573/24Safety recallInjuriesno date · EU Safety Gate

The propellant in the driver airbag may deteriorate over time. If the airbags deploy, it could result in fragments from the inflator injuring the vehicle's occupants. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

We could not check this: model year. The authority's notice

A12/02712/24Safety recallInjuriesno date · EU Safety Gate

Due to faulty rear-most screws, the screw fixings of the boot's lashing rails can fail in the event of a rear-end collision with heavy intrusion, and penetrate the backs of the rear seats. This increases the risk of injury to the occupants of the rear seats. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.

Remedy: Type of economic operator taking notified measure(s): Other Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

We could not check this: model year. The authority's notice

A12/02833/24Safety recallInjuriesno date · EU Safety Gate

The propellant in the driver airbag may deteriorate over time. If the airbags deploy, it could result in fragments from the inflator injuring the vehicle's occupants. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

We could not check this: model year. The authority's notice

A12/03084/24Safety recallInjuriesno date · EU Safety Gate

Due to faulty rear-most screws, the screw fixings of the boot's lashing rails can fail in the event of a rear-end collision with heavy intrusion and penetrate the backs of the rear seats. This increases the risk of injury to the occupants of the rear seats. The vehicles concerned have already been modified in connection with the recall code 0051960500. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

We could not check this: model year. The authority's notice

A12/03131/23Safety recallInjuriesno date · EU Safety Gate

The screw connection of the servo unit on the gear rack casing of the steering system may be faulty. This could cause the steering system to fail and become blocked, increasing the risk of an accident. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

We could not check this: model year. The authority's notice

A12/0440/18Safety recallInjuriesno date · EU Safety Gate

It is possible that the screws for attaching the rear spoiler were not fitted. The spoiler could become detached at high speeds endangering following vehicles.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

We could not check this: model year. The authority's notice

A12/0656/18Safety recallInjuriesno date · EU Safety Gate

In case of deployment of the driver airbag module, the gas generator could burst. If the gas generator bursts, metal fragments could pass through the airbag cushion material.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

We could not check this: model year. The authority's notice

A12/1159/19Safety recallInjuriesno date · EU Safety Gate

The airbag cover on the instrument panel may not have been manufactured according to specifications. As a result, in the event of an accident, the airbag may not deploy as designed, increasing the risk of an injury.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

We could not check this: model year. The authority's notice

A12/1218/19Safety recallInjuriesno date · EU Safety Gate

The screws for fastening the rear spoiler may not have been installed. As a result, the rear spoiler may detach in motion, endangering the following traffic.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

We could not check this: model year. The authority's notice

A12/1370/19Safety recallInjuriesno date · EU Safety Gate

The front seatbacks may not have been welded according to specifications. As a result, they could fold forward or rearward, increasing the risk of an injury to the occupants.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

We could not check this: model year. The authority's notice

A12/1525/18Safety recallInjuriesno date · EU Safety Gate

The coating of the rear brake caliper piston is defective, and impacts the piston movement. This can lead to reduced brake performance, or the rear brake circuit could even fail. This increases the risk of an accident.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

We could not check this: model year. The authority's notice

A12/1687/19Safety recallInjuriesno date · EU Safety Gate

The swivel bearings on the front axle may not have been manufactured according to specification and could break. This can result in loss of control over the vehicle, increasing the risk of an accident.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

We could not check this: model year. The authority's notice

SR/00358/26Safety recallInjuriesno date · EU Safety Gate

The steering system sensor may malfunction causing an unintended steering movement of the vehicle. This increases the risk of accidents and injuries. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

We could not check this: model year. The authority's notice

SR/01734/25Safety recallFireno date · EU Safety Gate

The positive battery cable of the starter-generator may not have been manufactured correctly. This could result in a loose electrical connection, leading to excessive contact resistance. The vehicle cannot charge or start. Contact points in the starter-generator could overheat and cause a vehicle fire. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

We could not check this: model year. The authority's notice

SR/01744/25Safety recallFireno date · EU Safety Gate

Failure to bolt the plus voltage (B+) cable tightly enough to the starter generator may result in contact problems and an increase in contact resistance at the bolted connection. This may in turn lead to local overheating and the vehicle catching fire or to the engine stalling while the vehicle is coasting. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

We could not check this: model year. The authority's notice

SR/01903/25Safety recallInjuriesno date · EU Safety Gate

Damaged brake discs may have been fitted to the front axle. This can lead the brakes to fail when a heavy load is placed on the wheel concerned, increasing the risk of accident and injuries. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

We could not check this: model year. The authority's notice

SR/03316/25Safety recallInjuriesno date · EU Safety Gate

Due to a manufacturing failure, the protection of the two outer headrests in the second row is reduced. In the event of a collision or accident, passengers could be injured. In addition, headrest parts may become exposed and also cause serious injuries. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

We could not check this: model year. The authority's notice

SR/03830/25Safety recallFireno date · EU Safety Gate

Water may come into contact with the starter relay and gradually cause corrosion. This could affect the electrical connection inside the relay and make the engine difficult to start. It may also result in a short circuit and could cause the starter to overheat leading to a fire when the vehicle is in motion or when it is parked with the ignition off. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

We could not check this: model year. The authority's notice

Engine and transmission

N57D30

190–230 kW (258–313 HP) · diesel

ZF8HP70 · 8-speed automatic, longitudinal (ZF 8HP70)

automatic · 8 speed

Torque limit700 Nm
MakerZF

We built the code from the model and the gear count. The factory sheet does not state it.

Variant data

What is in this version

Factory data

Trim
X3 40d xDrive
Body
SUV
Fuel
diesel
Transmission
automatic
Engine size
2993 cc
Power
223 kW (303 HP)
Drive
AWD
Production
2024–

Factory service interval

The manufacturer specifies this for this version. Of the mileage and the time, the one that comes first is the one that counts.

  • Air filter

    • 60,000 km or 4 years

  • Cabin (pollen) filter

    • 30,000 km or 2 years

  • Brake fluid change

    • first: 3 years, then 2 years(first change at 3 years, then every two years)

  • Engine oil and oil filter (BMW condition-based service)

    • LongLife25,000 km or 2 years

  • Fuel filter, diesel

    • 60,000 km or 2 years
All G01 versions

Information, not an expert opinion

We write the descriptions, and we put the source next to them. A person reviews them before they go out. They are still information, not a technical expert opinion.

  • A fault on the list does not mean the car you are looking at has it.
  • A fault missing from the list does not mean the model is fault-free. Write-ups are made model by model. Not all of them are done.
  • You decide whether to buy. This is no substitute for an inspection. That needs a workshop and a history check.
Details in the terms