vinkodex.

BMW X6 X6 xDrive35i Executive common faults.

2008–2012, SUV, petrol, 306 HP.

The fault list covers: N54B30, N55B30 engine, ZF6HP-BMW, ZF6HP26, ZF8HP, ZF8HP70 transmission.

What you save stays on this device only. My saves

13 fault write-ups. 12 important. 22 recalls.

If you know the year, pick it. Faults for other years drop out of the list.

Before you buy

Known faults

12 important faults

critical3

Electric water pump: silent failure, immediate overheating

critical

In these engines the water pump is not belt driven but has its own electric motor. It gains on fuel consumption, but it opens a new failure path: the pump or its electronics often simply stops with no warning. Measured in the official complaints, the typical mileage is 161,000 km (a tenth of the complaints already at 81,000, a tenth only above 257,000 km). So the common wisdom of "around 100,000 km" is early: most of the failures happen between 130,000 and 250,000 km.

Show the rest

With a belt driven pump the flow weakens gradually, here the circulation stops in an instant. In urban traffic the temperature crosses the limit within minutes, the cylinder head distorts, and the repair is an engine rebuild.

Replacing a still good pump at around 120,000 to 150,000 km costs less than repairing an overheated engine. If the replacement is already in the service book, the pump has already been changed.

between 81,000 and 257,000 km

What to check

  • Watch the coolant temperature gauge after startup: it should settle evenly, not jump around
  • Standing still with a warm engine, listen for whether the cooling fan and the pump are working
  • Ask for a fault code read: codes pointing at coolant flow belong here
2 more steps in the write-up

N52 / N55: aluminium bolts of the VANOS housing can loosen

critical

Four aluminium bolts hold the housing of the variable valve timing (VANOS). On some six cylinder engines built between late 2009 and mid 2012 these bolts loosen over time, and can also break.

Show the rest

If the housing moves, the timing becomes imprecise: the engine runs roughly, loses power, can drop into limp mode, and rarely can stall. That is why the maker started a safety recall (NHTSA 23V-707).

The recall covers the N51 / N52K / N52T / N55 engines; Their codes are N52B25, N52B30 and N55B30. The repair is replacing the four bolts; if a bolt is already broken or loose, the whole VANOS unit has to be replaced.

"No recall letter arrived" is not enough: ask at the workshop whether the repair code 0011520700 appears in the history.

between 134,000 and 300,000 km

What to check

  • Ask for the build date: the recall covers production between September 2009 and July 2012
  • Ask for the service history and look for the VANOS bolt / 0011520700 recall being carried out
  • On a cold start watch for rough running, jerking and loss of power
2 more steps in the write-up

Blower motor connector corrosion: short circuit and fire, even on a parked car

critical

The contacts between the wiring harness and the blower motor regulator wear against each other and corrode. The connection becomes unreliable, the connector heats up, the insulation of the harness is damaged, and that can lead to a short circuit and finally a vehicle fire.

Show the rest

The short circuit and the fire can happen while the engine is switched off, and also while the car is parked. A car standing in a garage can catch fire too.

According to the German technical press, in January 2021 around 430,000 cars in Germany and more than half a million worldwide were recalled for this, all E90/E91/E92/E93 3 Series. In the USA more than 700,000 2006 to 2011 3 Series cars had already been recalled for the same thing in autumn 2017, after claimants in three separate cases cited injuries. The maker disputed that the fault had ever caused personal injury or an accident.

The EU Safety Gate names it in two separate alerts: the 3 Series (A12/00390/21) and the X5/X6 (A12/01261/21).

The campaign is free, but only if it was carried out. On a fifteen year old car, ask about it, because nobody will offer it unprompted.

What to check

  • Ask the franchised dealer by VIN whether the blower motor connector campaign was carried out
  • Switch the blower on through every speed: a blower that hesitates or drops out at one speed can point to the connector fault
  • Smell the cabin with the blower running: burnt plastic or insulation is an immediate warning
2 more steps in the write-up

expensive9

Oil filter housing gasket: oil leak onto the belt and the alternator

expensive

A rubber gasket seals the oil filter housing to the block. The gasket hardens over the years, and oil leaks from under the housing. The oil drips onto the drive belt and the alternator.

Show the rest

Three things can happen. The oil stretches the belt and it can jump off (on a single belt engine that means an instant loss of the water pump and the alternator); oil getting into the alternator destroys the windings; and oil reaching the hot exhaust smokes and gives a burnt smell, and the official complaints do include burning smells and smoke.

The leak is visible: five minutes on a lift settles it. The gasket itself is a cheap part; the labour, the ruined belt and the alternator take the money.

between 64,000 and 246,000 kmreported complaints only

What to check

  • On a lift look at the block surface around the oil filter housing: a wet, oily or oily dusty film
  • Look at the drive belt: an oily, cracked, stretched belt is the consequence of the leak
  • Look at the alternator housing from below: an oil trail indicates damage reaching the windings
2 more steps in the write-up

VANOS solenoid valve: a clogging filter screen and late camshaft adjustment

expensive

VANOS adjusts the position of the camshaft with the pressure of the engine oil, and a solenoid valve metres that pressure. The valve sits in the oil circuit, and a fine filter screen protects the spool inside it from larger particles. That screen clogs with carbon and deposits: less oil flows through, and VANOS then adjusts late or does not move at all. The symptoms are a rough idle, rough running, a lack of torque at low revs and higher fuel consumption, because the valve timing is off. A short metallic clacking can also come on a cold start and goes quiet after 10 to 20 seconds. The engine warning light comes on with a camshaft fault code, and depending on the severity the engine control unit switches to limp mode. The fault code narrows down the cause. P0010 and P0013 typically mean the solenoid valve itself, that is a circuit fault or reduced oil flow through the clogged screen. P0011 and P0014 point more to a mechanical cause: a stretched timing chain or a worn adjuster. P0012 and P0015 report late camshaft control, whose common cause is slow pressure build-up at the adjuster, so again the dirty valve. The valve itself is a small part, between 50 and 120 euro, and with a clean screen cleaning is often enough; replacing the whole adjuster, by contrast, is a four-figure job. The reported repairs ran between 80 and 1,200 euro, depending on whether cleaning is enough and how many valves are affected. The main cause of the screen clogging is a stretched oil change interval and carbon-laden oil.

between 70,000 and 120,000 km80–1,200 EUR

What to check

  • Read the fault memory and note the exact code: P0010 and P0013 point to the valve
  • If P0011 or P0014 is stored, the timing chain has to be checked as well
  • Start the engine cold and listen for metallic clacking in the first 10 to 20 seconds
2 more steps in the write-up

XDrive transfer case (ATC): binding in corners, plastic actuator gear

expensive

The heart of the four wheel drive in the longitudinal engine BMW X models (X3, X5 and the X1 E84) is the ATC transfer case. It has two faults, and you can feel both while driving.

Show the rest

The first is wear of the clutch pack and the fluid: in a slow, tight corner (a car park, a roundabout) the car jerks and "hops", as if the drive grabbed and let go. You can also get a jerk when pulling away on a slope. The second is the plastic actuator gear: the position signal is lost, the brake, ABS and 4x4/DSC lights come on together on the dash, and a clicking is audible from the transfer case when you switch the ignition off.

Workshops often propose a full transfer case replacement straight away. But the plastic gear can be replaced on its own, and the wrong tyre size or a mixed set of tyres also imitates the jerking, because the transfer case then slips continuously. So clear up the tyres and the fault code first, before you pay for a transfer case replacement.

between 72,000 and 175,000 km

What to check

  • In a slow, tight corner (a car park) watch for jerking, binding and a "skipping" feel
  • When pulling away on light throttle, can you feel the drivetrain jerk
  • Watch the dash: 4x4, ABS, DSC and brake lights together point at the actuator
4 more steps in the write-up

Crankcase ventilation (CCV) in the valve cover: oil consumption, rough running

expensive

The crankcase ventilation leads the gas that forms in the crankcase back to the intake and separates the oil out of it on the way. If the system clogs or the membrane tears, the pressure cannot get away: it finds a way out past the seals, or it pushes the oil through the piston rings. This is where the oil consumption comes from, and the oil that appears around the valve cover gasket. In the other direction a faulty breather takes unmetered air into the intake, and that is what makes the idle rough, the throttle response hesitant and the running coarse. Starting also gets harder, and in an extreme case the engine stalls at idle. Two characteristic signs help: weak or absent suction at the oil filler with the engine running, and noticeably rough running around 3,000 rpm. The hose at the rear of the valve cover can also let oil out. The sound insulation then soaks itself with oil, and oil gets everywhere in the engine bay. On the six-cylinder engines the breather is built into the valve cover, so the repair is replacing the cover or the whole oil separator together with the hoses, between 80 and 900 euro.

between 80,000 and 150,000 km80–900 EUR

What to check

  • With the engine running unscrew the oil filler cap: weak or absent suction is a sign
  • Look around the valve cover and at the rear of the engine bay for oil traces
  • Watch the idle, and the rough running around 3,000 rpm
2 more steps in the write-up

ZF 6HP automatic: mechatronics connector sealing sleeve leaks

expensive

In the ZF six speed automatic (BMW codes GA6HP19Z / GA6HP26Z) the electrical connector of the valve body control leaves the gearbox housing through a plastic sleeve. That sleeve and its seals age, and they let oil through.

Show the rest

The symptom is irregular shifting, a gear slipping at higher revs, limp mode, a drivetrain fault code and a message on the display. The cause is the same in each case: the leak drops the hydraulic pressure, and the valve body cannot close the clutches with enough force.

The sleeve can be replaced without removing the gearbox, you only have to drop the oil pan. If it leaks for a long time, the slipping clutch and the overheating pump take the inside of the gearbox with them, and from then on it is a rebuild. The factory calls the oil a lifetime fill, but in practice the sleeve wears out around 60,000 to 70,000 miles, roughly 100,000 to 115,000 km.

between 100,000 and 200,000 km

What to check

  • On a lift look at the right side of the gearbox housing, above the oil pan: a wet, oily connector is the characteristic picture
  • On the test drive watch the shifts cold and warm: jerking, delay, slipping at higher revs
  • Ask for a fault code read from the gearbox controller: gear ratio fault, pressure regulation
2 more steps in the write-up

N54 / N55: high pressure fuel pump

expensive

This is the most common N54 fault, and it affects early N55 engines too. The pump is a two part design: fuel goes into one half and lubricating oil into the other, and the sealing ring separating them ages over time. That is what drops the pressure.

Show the rest

The very first symptom is a long crank: the engine does not catch straight away but turns over for several seconds. Later you get a rough idle, misfire, loss of power, and finally limp mode, which can reach you at the side of the road.

The fault code is typically P0087 or P0089. If the control unit also returns a camshaft timing code (P0011, P0012), that is often not a separate fault but a consequence of the pressure drop: it is worth ruling the pump out first.

The 2007 to 2009 cars are the worst; the maker revised the design after that.

The N53 (the lean burn six cylinder sold in Europe) got the same pump. Faults were reported on it. It is not known whether they are as frequent as on the N54, because the N53 was not sold in the USA and there is no official complaint data on it.

between 114,000 and 256,000 km

What to check

  • Cold start: the engine must catch straight away. Several seconds of cranking is the first sign
  • Restart it once or twice when warm too, and watch for the same thing
  • Load the engine on the test drive: jerking, loss of power and limp mode are suspect
2 more steps in the write-up

ZF 8HP automatic: mechatronics unit and connector sleeve leak

expensive

The ZF eight speed automatic (BMW Steptronic 8HP family) has two faults, and you can feel both.

Show the rest

The first is the mechatronics unit: the valve body and the control electronics in one. If the solenoids or the pressure regulation weaken, the gearbox jerks, the D/R engagement is delayed, it logs a gear ratio fault code, and finally drops into limp mode (often staying in 2nd or 3rd).

The second, and often misdiagnosed, is the connector sleeve of the mechatronics unit: the O-ring of the plastic sleeve ages, and ATF leaks from the side of the housing, exactly where the wiring harness enters. This is easy to mistake for a rear crankshaft seal. The trail starts from the driver's side of the housing, not from the clutch side.

On cars built in 2023 there was also a separate safety recall for a welding fault in the mechatronics unit. That is not the same as the wear related sleeve and the valves.

Check the fluid level, the area around the sleeve and the fault codes first; do not accept a "full gearbox replacement" quote straight away.

above 120,000 km

What to check

  • On the test drive watch for delayed D/R engagement, a jerk when shifting, and limp mode (a stuck gear)
  • Look at the driver's side of the gearbox housing where the wiring harness enters: an ATF trail from the sleeve is suspect
  • Do not confuse it with a rear crankshaft seal leak: the direction of the trail decides
3 more steps in the write-up

Valvetronic: oil in the sensor connector, a worn eccentric shaft

expensive

Valvetronic adjusts the lift of the intake valves, and an eccentric shaft does that work. Three parts can fail here, at very different prices, and their symptoms are nearly identical.

Show the rest

The sensor is usually the first to give up: oil leaks past its seal into the connector, and the oil corrupts the signal the engine control unit depends on. From then on the control unit gets no reliable position feedback, cannot set the valve lift precisely, and switches to a protective strategy. The fault code in this case is a plausibility fault, 2A67 or 2A6B: the control unit does not consider the position signal credible.

The eccentric shaft itself can also wear out or seize, and there are several causes for that: lack of lubrication from oil sludge and skipped oil changes, wear of the bearings, a system driven on with a failed actuator motor, and overheating and oil contamination in the cylinder head. It is reported from 150 000 kilometres.

The symptom is similar in all three cases: an unstable idle, stumbling and long cranking at a cold start, a check engine light that comes on and goes out on its own, lack of power or limp mode, inconsistent throttle response, and misfires cylinder by cylinder. A clicking, binding noise from the engine bay points to a seizing shaft.

The misdiagnosis is common, because the symptom shows up at combustion, so coils and spark plugs are suspected first, while the fault is in the air control. The condition of the shaft can only be established after the valve cover has been removed and it has been inspected. The sensor connector, though, is worth opening up first: if it is oily, that is the far cheaper route.

above 150,000 km

What to check

  • Open up the connector of the eccentric shaft sensor: an oily connector means the cheaper fault
  • Watch the revs at idle: an unstable idle and misfires cylinder by cylinder belong here
  • Start it cold: stumbling and long cranking are symptoms
3 more steps in the write-up

Wastegate rattle: the bushing wears out, and a repair kit fixes it

expensive

The boost control valve of the turbos, the wastegate, wears out, and the rattle can come from two places: either the flapper knocks against the sealing face, or the shaft is loose in its bushing. The noise is most audible at idle and at light load.

Show the rest

As the wear grows the assembly gets looser and looser, and the valve either does not close properly at spool-up or sticks open. Boost then falls away, the engine loses power and can go into limp mode. In community reports the 30FF underboost code goes with this.

The repair is not necessarily a turbo replacement, and that is the point. A repair kit is available, for both turbos at once: a stainless bushing, flapper, wastegate arm, rod end and retaining clip. The diameter of the bushing goes up from 11.5 millimetres to 12.6. The kit costs 95 dollars, but the turbos have to come off, the new assemblies have to be pressed into the turbo housing and then welded. That is work for a specialist, but it can be done in a day.

One thing is worth knowing at a viewing: adjusting the nut of the actuator arm can reduce the rattle temporarily. A quiet engine on its own therefore proves nothing.

What to check

  • Listen to the turbos at idle and at light load: a rattle points to the wastegate
  • Do not take quiet as proof: adjusting the actuator arm can reduce the noise temporarily
  • Accelerate hard: a drop in boost and limp mode point to the same place
3 more steps in the write-up

cheap repair1

Plastic charge pipe: it goes brittle and cracks at the throttle body

cheap repair

The maker builds the charge pipe out of plastic, and the coupler at the throttle body is the critical point. The material goes brittle from heat cycles, from boost pressure and from the heat of the engine bay, and then it cracks. Three things coincide here: the moulded coupler carries both pressure and movement, the vibration of the engine arrives here through the throttle body, and the spot gets continuous heat load. The crack starts on the inner radius of the coupler. The symptom is a loss of pressure under load: the engine pulls cleanly at part throttle but flattens out at full throttle, and a hissing noise is audible from the engine bay at the same time. A yellow drivetrain warning comes with it, which often disappears after a restart, and sometimes a brief limp mode. One thing is worth knowing: a clean fault memory does not rule the crack out. The pipe has no sensor of its own, so the control unit can only log a boost pressure fault, and the leak is intermittent, appearing only under load. At a viewing two things are visible without tools. On the inner radius of the coupler the hairline crack sometimes comes with dark staining, because the oil mist in the boost air escapes through it. For the same reason a greasy, dark ring can appear at the joint of the coupler. The crack is reported above 80 000 kilometres, and replacing the pipe costs between 100 and 400 euros, because the part itself is not expensive. The most common misdiagnosis against that is replacing the turbocharger, which costs an order of magnitude more, and a pressure test protects against it. The factory repair is the same plastic part, which can crack again at a similar mileage; replaced with an aluminium pipe this failure mode disappears, and the driveability does not change.

above 80,000 km100–400 EUR

What to check

  • Look at the inner radius of the coupler at the throttle body: the hairline crack sometimes comes with dark staining
  • Look for a greasy, dark ring at the joint of the coupler
  • On a motorway slip road at full throttle watch for the loss of pressure and the hissing noise
2 more steps in the write-up

Checklist

BMW X6 X6 xDrive35i Executive

First what you would check on any car. Then the faults of this model.

Before you buy

Checklist

The printed sheet starts with what you would check on any car. What you tick stays on this device only.

On every car

Ask the owner

Faults of this model

vinkodex.com · Before you buy it, see what can go wrong.

Official recall22 recallsShow

The manufacturer fixes these for free at a franchised dealer. Ask with the VIN whether it was done.

Most recent: 29 June 2021

A12/01929/23Safety recallInjuries29 June 2021 · EU Safety Gate

The propellant in the driver airbag can deteriorate due to high humidity and temperature variations. In the event of an accident in which the airbag deploys, this could result in fragments from the inflator casing coming loose and injuring the vehicle’s occupants. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: 29/06/2021

We could not check this: model year. The authority's notice

A12/01931/23Safety recallInjuries29 June 2021 · EU Safety Gate

The propellant in the passenger airbag can deteriorate due to high humidity and temperature variations. In the event of an accident in which the airbag deploys, this could result in fragments from the inflator casing coming loose and injuring the vehicle’s occupants. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: 29/06/2021

We could not check this: model year. The authority's notice

20V016000AIR BAGS:FRONTAL:PASSENGER SIDE:INFLATOR MODULEAIR BAGS:FRONTAL:PASSENGER SIDE:INFLATOR MODULE15 January 2020 · NHTSA (USA)

BMW of North America, LLC (BMW) is recalling certain 2009-2012 X5 xDrive35d, 2008-2012 X6 xDrive35i, X6 xDrive50i and X6 M, 2007-2012 X5 30si, X5 xDrive30i, X5 xDrive35i, X5 48i, X5 xDrive48i, X5 xDrive50i and X5 M and 2010-2011 X6 ActiveHybrid vehicles equipped with non-desiccated, passenger frontal air bag inflators containing phase stabilized ammonium nitrate (PSPI-2) propellant that were used as interim remedy parts for previous Takata recalls. These inflators may explode due to propellant degradation occurring after long-term exposure to high absolute humidity, high temperatures, and high temperature cycling.

Risk: An inflator explosion may result in sharp metal fragments striking the driver or other occupants resulting in serious injury or death.

Remedy: Owners are advised not to drive their vehicles until this remedy is performed. BMW will notify owners, and dealers will replace the passenger front air bag, free of charge. The recall began March 11, 2020. Owners may contact BMW customer service at 1-800-525-7417.

We could not check this: model year. The authority's notice

20V017000AIR BAGS:FRONTAL:DRIVER SIDE:INFLATOR MODULEAIR BAGS:FRONTAL:DRIVER SIDE:INFLATOR MODULE15 January 2020 · NHTSA (USA)

BMW of North America, LLC (BMW) is recalling certain 2008-2013 128i and 135i Convertibles, 128i, 135i, and M Coupes, 2007-2010 X3 30si and X3 xDrive30i, 2013-2015 X1 sDrive28i, X1 xDrive28i and X1 xDrive35i, 2007-2013 328i, 328i xDrive, 335i, 335is, 335i xDrive and M3 Coupes, 2006-2011 328i, 328xi, 328i xDrive, 325i, 325xi, 330i, 330xi, 335i, 335xi, 335i xDrive and M3, 2009-2011 335D, 2006-2012 325xi, 328i, 328xi and 328i xDrive, 2010-2011 X6 ActiveHybrid, 2007-2013 328i, 335i, 335is, M3 Coupes, X5 30si, X5 xDrive30i, X5 xDrive35i, X5 48i, X5 xDrive48i, X5 xDrive50i and X5 M, 2009-2013 X5 xDrive35d and 2008-2014 X6 xDrive35i, X6 xDrive50i and X6M vehicles equipped with non-desiccated driver frontal air bag inflators containing phase stabilized ammonium nitrate (PSAN) that were used as interim remedy parts for previous Takata recalls. These inflators may explode due to propellant degradation occurring after long-term exposure to high absolute humidity, high temperatures, and high temperature cycling.

Risk: An inflator explosion may result in sharp metal fragments striking the driver or other occupants resulting in serious injury or death.

Remedy: BMW will notify owners, and dealers will replace the driver air bag. On X5 and X6 vehicles, only the inflator will be replaced. All repairs will be performed free of charge. The recall began March 11, 2020. Owners may contact BMW customer service at 1-800-525-7417.

We could not check this: model year. The authority's notice

A12/01883/23Safety recallInjuries18 February 2019 · EU Safety Gate

The propellant in the driver airbag can deteriorate due to high humidity and temperature variations. In the event of an accident in which the airbag deploys, this could result in fragments from the inflator casing coming loose and injuring the vehicle’s occupants. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: 18/02/2019

We could not check this: model year. The authority's notice

19V017000AIR BAGS:FRONTAL:PASSENGER SIDE:INFLATOR MODULEAIR BAGS:FRONTAL:PASSENGER SIDE:INFLATOR MODULE14 January 2019 · NHTSA (USA)

BMW of North America, LLC (BMW) is recalling certain 2007-2013 X5 xDrive30i, X5 xDrive35i, X5 xDrive48i, X5 xDrive50i and X5 M vehicles, 2008-2014 X6 xDrive35i, X6 xDrive50i and X6 M vehicles, 2009-2013 X5 xDrive35d vehicles and 2010-2011 X6 ActiveHybrid vehicles. These vehicles are equipped with certain air bag inflators assembled as part of the passenger frontal air bag modules used as original equipment or replacement equipment. In the event of a crash necessitating deployment of the passenger frontal air bag, these inflators may explode due to propellant degradation occurring after long-term exposure to absolute humidity and temperature cycling.

Risk: An inflator explosion may result in sharp metal fragments striking the driver or other occupants resulting in serious injury or death.

Remedy: Owners are advised not to drive their vehicles until the remedy is performed. BMW will notify owners, and dealers will replace the passenger frontal air bag module, free of charge. The recall began March 14, 2019. Owners may contact BMW customer service at 1-800-525-7417.

We could not check this: model year. The authority's notice

18V248000ENGINE AND ENGINE COOLING:ENGINE:GASOLINE:TURBO/SUPERCHARGERENGINE AND ENGINE COOLING:ENGINE:GASOLINE:TURBO/SUPERCHARGER18 April 2018 · NHTSA (USA)

BMW of North America, LLC (BMW) is recalling certain 2011-2012 BMW 550i, 550i xDrive, 550i Gran Turismo, 550i Gran Turismo xDrive, 750i, 750Li, 750i xDrive, 750Li xDrive, 760Li, X5 xDrive50i, X5 M, X6 xDrive50i, X6 M, ActiveHybrid7, MINI Cooper S Convertible, John Cooper Works (JCW) Convertible, Cooper S Countryman, Cooper S Countryman ALL4, Cooper S, JCW, Cooper S Clubman, JCW Clubman, Cooper S Roadster, JCW Roadster, Cooper S Coupe, JCW Coupe and Rolls-Royce Ghost, 2011 BMW X6 Hybrid and 2012 BMW 650i Coupe, 650i xDrive Coupe, 650i Convertible and 650i xDrive Convertible vehicles. The electric auxiliary water pump may fail and cause the circuit board to overheat.

Risk: If the circuit board were to overheat, it can increase the risk of a fire.

Remedy: BMW will notify owners, and dealers will replace the electric auxiliary water pump, free of charge. Depending on the model, there are currently limited parts available, however not all parts are available at this time. Owners will be notified of the recall beginning June 11, 2018, and will receive a second notification when remedy parts become available. Owners may contact BMW customer service at BMW 1-800-525-7417, MINI at 1-866-825-1525, or Rolls-Royce at 1-877-877-3735. Note: BMW recommends that owners park their vehicle outdoors until the recall remedy has been performed.

We could not check this: model year. The authority's notice

18V030000AIR BAGS:FRONTAL:PASSENGER SIDE:INFLATOR MODULEAIR BAGS:FRONTAL:PASSENGER SIDE:INFLATOR MODULE9 January 2018 · NHTSA (USA)

BMW of North America, LLC (BMW) is recalling certain 2007-2013 X5 xDrive30i, X5 xDrive35i, X5 xDrive48i, X5 xDrive50i, X5 M, 2009-2010 X5 xDrive35d vehicles and 2009-2013 X6 xDrive35i, X6 xDrive50i, and X6 M vehicles ever registered in the states of Alabama, California, Florida, Georgia, Hawaii, Louisiana, Mississippi, South Carolina, Texas, Puerto Rico, American Samoa, Guam, the Northern Mariana Islands (Saipan), and the U.S. Virgin Islands or "Zone A." BMW is also recalling certain 2007-2010 X5 xDrive30i, X5 xDrive35i, X5 xDrive48i, X5 xDrive50i, X5 M, X5 xDrive35d, X6 xDrive35i, X6 xDrive50i and X6M vehicles ever registered in the states of Arizona, Arkansas, Delaware, District of Columbia, Illinois, Indiana, Kansas, Kentucky, Maryland, Missouri, Nebraska, Nevada, New Jersey, New Mexico, North Carolina, Ohio, Oklahoma, Pennsylvania, Tennessee, Virginia, and West Virginia or "Zone B." BMW is also recalling certain 2007-2009 X5 xDrive30i, X5 xdrive35i, X5 xDrive48i, X5 xDrive50i, X5 M, X5 xDrive35d, X6 xDrive35i, X6 xDrive50i and X6M vehicles ever registered in the states of AK, CO, CT, ID, IA, ME, MA, MI, MN, MT, NH, NY, ND, OR, RI, SD, UT, VT, WA, WI, and WY or "Zone C." These vehicles are equipped with certain air bag inflators assembled as part of the passenger frontal air bag modules used as original equipment or replacement equipment. In the event of a crash necessitating deployment of the passenger frontal air bag, these inflators may explode due to propellant degradation occurring after long-term exposure to absolute humidity and temperature cycling.

Risk: An inflator explosion may result in sharp metal fragments striking the driver or other occupants resulting in serious injury or death.

Remedy: Owners are advised not to drive their vehicles until the remedy is performed. BMW will notify owners, and dealers will replace the passenger front air bag module, free of charge. The recall is expected to begin March 2018. Owners may contact BMW customer service at 1-800-525-7417.

We could not check this: model year. The authority's notice

17V138000POWER TRAIN:DRIVELINE:DRIVESHAFTPOWER TRAIN:DRIVELINE:DRIVESHAFT2 March 2017 · NHTSA (USA)

BMW of North America, LLC, (BMW) is recalling certain 2011-2013 X5 xDrive35i, X5 xDrive50i, X5 M and X5 xDrive35d vehicles, 2011-2014 X6 xDrive35i, X6 xDrive50i and X6M vehicles, and 2011 x6 ActiveHybrid Vehicles. Water and debris may enter the front driveshaft's universal joint, causing excessive wear and possibly resulting in the joint's failure.

Risk: If the front universal joint fails, the front wheels would not be driven, affecting vehicle traction. Additionally, continued driving of the vehicle with a broken front universal joint may damage other components. Either condition may increase the risk of a crash.

Remedy: BMW will notify owners, and dealers will replace the front driveshaft, free of charge. The recall began on April 18, 2017. Owners may contact BMW customer service at 1-800-525-7417.

We could not check this: model year. The authority's notice

17V020000AIR BAGS:FRONTAL:PASSENGER SIDE:INFLATOR MODULEAIR BAGS:FRONTAL:PASSENGER SIDE:INFLATOR MODULE10 January 2017 · NHTSA (USA)

BMW of North America, LLC (BMW) is recalling certain 2012 X5 xDrive30i, X5 xDrive35i, X5 xDrive48i, X5 xDrive50i, X5 M, X6 xDrive35i, X6 xDrive50i, and X6 M vehicles originally sold, or ever registered, in Alabama, California, Florida, Georgia, Hawaii, Louisiana, Mississippi, South Carolina, Texas, Puerto Rico, American Samoa, Guam, the Northern Mariana Islands (Saipan), and the U.S. Virgin Islands, or "Zone A." Additionally, unless included in "Zone A" above, BMW is recalling certain 2009 X5 xDrive30i, X5 xDrive35i, X5 xDrive48i, X5 xDrive50i, and X5 M vehicles, 2008-2009 X6 xDrive 35i, X6 xDrive50i, X6 M, and 2009 X5 xDrive35d vehicles originally sold, or ever registered, in Arizona, Arkansas, Delaware, District of Columbia, Illinois, Indiana, Kansas, Kentucky, Maryland, Missouri, Nebraska, Nevada, New Jersey, New Mexico, North Carolina, Ohio, Oklahoma, Pennsylvania, Tennessee, Virginia, and West Virginia, or "Zone B." Additionally, unless included in "Zone A" or "Zone B" above, BMW is recalling certain 2007-2008 X5 xDrive30i, X5 xDrive35i, X5 xDrive48i, X5 xDrive50i and X5 M vehicles, and 2008 X6 xDrive35i, X6 xDrive50i, and X6 M vehicles originally sold, or ever registered in the states of Alaska, Colorado, Connecticut, Idaho, Iowa, Maine, Massachusetts, Michigan, Minnesota, Montana, New Hampshire, New York, North Dakota, Oregon, Rhode Island, South Dakota, Utah, Vermont, Washington, Wisconsin, and Wyoming. These vehicles are equipped with certain air bag inflators assembled as part of the passenger frontal air bag modules used as original equipment or replacement equipment. In the event of a crash necessitating deployment of the front air bags, these inflators may rupture due to propellant degradation occurring after long-term exposure to high absolute humidity and temperature cycling.

Risk: An inflator rupture may result in metal fragments striking the vehicle occupants resulting in serious injury or death.

Remedy: Owners are advised not to drive their vehicles until the remedy is performed. BMW will notify owners, and dealers will replace the front passenger air bag inflator or air bag module, free of charge. Interim letters were mailed March 2017. Owners will receive a second notice when remedy parts become available. Owners may contact BMW customer service at 1-800-525-7417.

We could not check this: model year. The authority's notice

16V746000FUEL SYSTEM, GASOLINE:DELIVERY:FUEL PUMPFUEL SYSTEM, GASOLINE:DELIVERY:FUEL PUMP17 October 2016 · NHTSA (USA)

BMW of North America, LLC (BMW) is recalling certain model year 2007-2011 BMW X5 3.0si, X5 4.8i, X5 M, X5 xDrive30i, X5 xDrive35i, X5 xDrive48i and X5 xDrive50i, 2008-2011 X6 x Drive35i, X6 xDrive50i and X6 M, 2010-2011 X6 ActiveHybrid, 535i xDrive Gran Turismo, 535i Gran Turismo, 550i xDrive Gran Turismo and 550i Gran Turismo, 2011-2012 528i, 535i, 535i xDrive, 550i and 550i xDrive and 2012 535i ActiveHybrid, 640i Convertible, 650i Convertible, 650i xDrive Convertible, 650i Coupe and 650i Coupe xDrive vehicles. The affected vehicles have in-tank fuel pumps that may have insufficiently crimped wire contacts.

Risk: The loose wires may cause the connector to melt, resulting in a fuel leak. Additionally, the fuel pump may stop working, possibly causing an engine stall and increase the risk of a crash.

Remedy: BMW will notify owners, and dealers will replace the fuel pump module, free of charge. The recall began February 2017. Owners may contact BMW customer service at 1-800-525-7417.

We could not check this: model year. The authority's notice

16V364000AIR BAGS:FRONTAL:PASSENGER SIDE:INFLATOR MODULEAIR BAGS:FRONTAL:PASSENGER SIDE:INFLATOR MODULE25 May 2016 · NHTSA (USA)

BMW of North America, LLC (BMW) is recalling certain model year 2007-2011 X5 xDrive30i, X5 xDrive35i, X5 xDrive48i, X5 xDrive50i and X5M vehicles, 2009-2011 X5 xDrive35d vehicles, 2008-2011 X6 xDrive35i, X6 xDrive50i and X6 M vehicles, and 2010-2011 X6 ActiveHybrid vehicles originally sold, or ever registered, in Alabama, California, Florida, Georgia, Hawaii, Louisiana, Mississippi, South Carolina, Texas, Puerto Rico, American Samoa, Guam, the Northern Mariana Islands (Saipan), and the U.S. Virgin Islands, or "Zone A." Additionally, unless included in "Zone A" above, BMW is recalling certain model year 2007-2008 X5 xDrive30i, X5 xDrive35i, X5 xDrive48i, X5 xDrive50i and X5M vehicles, and 2008 BMW X6 xDrive35i, X6 xDrive50i and X6 M vehicles originally sold, or ever registered, in Arizona, Arkansas, Delaware, District of Columbia, Illinois, Indiana, Kansas, Kentucky, Maryland, Missouri, Nebraska, Nevada, New Jersey, New Mexico, North Carolina, Ohio, Oklahoma, Pennsylvania, Tennessee, Virginia, and West Virginia, or "Zone B." Vehicles of these model years and models that were not originally sold or ever registered in either Zones A or B are not subject to this safety recall. These vehicles are equipped with certain air bag inflators assembled as part of the passenger frontal air bag modules, and used as original equipment or replacement equipment. In the event of a crash necessitating deployment of the front air bags, these inflators may rupture due to propellant degradation occurring after long-term exposure to high absolute humidity and temperature cycling.

Risk: An inflator rupture may result in metal fragments striking the vehicle occupants resulting in serious injury or death.

Remedy: Owners are advised not to drive their vehicles until they have been repaired. BMW will notify owners, and dealers will replace the passenger frontal air bag inflator or air bag module, free of charge. The recall began July 28, 2017. Owners may contact BMW customer service at 1-800-525-7417.

We could not check this: model year. The authority's notice

16V311000POWER TRAIN:DRIVELINE:DRIVESHAFTPOWER TRAIN:DRIVELINE:DRIVESHAFT17 May 2016 · NHTSA (USA)

BMW of North America, LLC (BMW) is recalling certain model year 2011 X5 xDrive 35i, xDrive50i, X5 M, X6 xDrive35i, X6 xDrive50i, and X6 M vehicles manufactured April 5, 2010, to November 20, 2010, 2011 X5 xDrive35d diesel vehicles manufactured April 7, 2010, to November 20, 2010, and 2011 X6 Active Hybrid vehicles manufactured April 15, 2010, to November 17, 2010. The affected vehicles have a front driveshaft universal joint that may not seal out water and debris from getting in and damaging the joint, which could lead to its failure.

Risk: If the front universal joint fails, the front wheels would not be driven, affecting vehicle traction. Additionally, continued driving of the vehicle with a broken front universal joint may damage other components. Either condition may increase the risk of a crash.

Remedy: BMW will notify owners, and dealers will replace the front driveshaft, free of charge. The recall began on July 8, 2016. Owners may contact BMW customer service at 1-800-525-7417.

We could not check this: model year. The authority's notice

12V267000STEERINGSTEERING13 June 2012 · NHTSA (USA)

BMW IS RECALLING CERTAIN MODEL YEAR 2012 X5 VEHICLES EQUIPPED WITH A DIESEL ENGINE AND 2013 X5 AND X6 VEHICLES. DUE TO A MACHINING ERROR OF THE STEERING GEAR SURFACE, POWER STEERING FLUID MAY LEAK.

Risk: LEAKING POWER STEERING FLUID CAN SPRAY ONTO HOT EXHAUST PARTS, INCREASING THE RISK OF AN ENGINE COMPARTMENT FIRE.

Remedy: BMW WILL NOTIFY OWNERS, AND DEALERS WILL INSPECT, AND IF NECESSARY, REPLACE THE STEERING GEAR FREE OF CHARGE. THE SAFETY RECALL BEGAN ON JULY 20, 2012. OWNERS MAY CONTACT BMW CUSTOMER RELATIONS AND SERVICES AT 1-800-525-7417.

We could not check this: model year. The authority's notice

11V521000ENGINE AND ENGINE COOLING:ENGINE:OTHER FUEL TYPES:TURBO/SUPERCHARGERENGINE AND ENGINE COOLING:ENGINE:OTHER FUEL TYPES:TURBO/SUPERCHARGER20 October 2011 · NHTSA (USA)

BMW IS RECALLING CERTAIN MODEL YEAR 2011 5-SERIES, MODEL YEAR 2010-2011 5-SERIES GRAN TURISMO, MODEL YEAR 2009-2011 7-SERIES, MODEL YEAR 2010-2011 X5 SAV, AND MODEL YEAR 2008-2011 X6 SAV VEHICLES EQUIPPED WITH 8- OR 12-CYLINDER, TURBOCHARGED, ENGINES BECAUSE THE CIRCUIT BOARD FOR THE ELECTRIC AUXILIARY WATER PUMP CAN OVERHEAT.

Risk: THIS COULD LEAD TO A SMOLDERING OF THE PUMP OR AN ENGINE COMPARTMENT OR VEHICLE FIRE.

Remedy: BMW WILL NOTIFY OWNERS, AND DEALERS WILL REPLACE THE AUXILIARY WATER PUMP FREE OF CHARGE. THE SAFETY RECALL BEGAN ON DECEMBER 19, 2011. OWNERS MAY CONTACT BMW CUSTOMER RELATIONS AND SERVICES AT 1-800-525-7417.

We could not check this: model year. The authority's notice

10V233000EQUIPMENT:OTHER:LABELSEQUIPMENT:OTHER:LABELS2 June 2010 · NHTSA (USA)

BMW IS RECALLING CERTAIN MODEL YEAR 2011 X5 SAV AND X6 SAV PASSENGER VEHICLES MANUFACTURED FROM APRIL 1 THROUGH MAY 8, 2010. THE TIRE LABEL DOES NOT CONFORM TO THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 110, "TIRE SELECTION AND RIMS." THE VEHICLES ARE EQUIPPED WITH 20-INCH WHEELS, BUT THE LABEL STATES THAT THE VEHICLES WERE EQUIPPED WITH 19-INCH WHEELS AND THE STATED TIRE PRESSURE IS INCORRECT FOR THE EQUIPPED WHEELS.

Risk: IMPROPER TIRE INFLATION CAN RESULT IN PREMATURE TIRE FAILURE OR REDUCED VEHICLE HANDLING PERFORMANCE, EITHER OF WHICH CAN INCREASE THE RISK OF A CRASH.

Remedy: BMW WILL NOTIFY OWNERS AND PROVIDE CORRECT LABELS FREE OF CHARGE. THE OWNER WILL HAVE THE OPTION TO AFFIX THE LABEL THEMSELVES OR THEY MAY TAKE THEIR VEHICLE TO A BMW DEALER WHO WILL AFFIX THE LABEL FOR THEM AT NO COST. THE SAFETY RECALL BEGAN ON OCTOBER 8, 2010. OWNERS MAY CONTACT BMW AT 1-800-525-7417.

We could not check this: model year. The authority's notice

10V025000VISIBILITY:WINDSHIELDVISIBILITY:WINDSHIELD28 January 2010 · NHTSA (USA)

BMW IS RECALLING CERTAIN MODEL YEAR 2010 X5 AND X6 SPORT ACTIVITY VEHICLES MANUFACTURED BETWEEN DECEMBER 14, 2009 AND DECEMBER 16, 2009. IN THE UPPER RIGHT AREA OF THE WINDSHIELD, BONDING MAY BE INSUFFICIENT OVER A LENGTH OF APPROXIMATELY 50CM.

Risk: IN THE CASE OF A ROLLOVER, THE STABILITY OF THE ROOF COULD BE AFFECTED INCREASING THE RISK OF INJURIES.

Remedy: BMW WILL NOTIFY OWNERS AND AUTHORIZED DEALERS WILL REMOVE THE WINDSHIELD AND THEN REINSTALL WITH THE PROPER BONDING FREE OF CHARGE. THE SAFETY RECALL BEGAN ON MARCH 30, 2010. OWNERS MAY CONTACT BMW AT 1-800-525-7417.

We could not check this: model year. The authority's notice

09V255000SERVICE BRAKES, HYDRAULIC:FOUNDATION COMPONENTS:DISCSERVICE BRAKES, HYDRAULIC:FOUNDATION COMPONENTS:DISC8 July 2009 · NHTSA (USA)

BMW IS RECALLING MY 2009 X5 AND X6 VEHICLES. THE REAR BRAKE DISCS MAY NOT HAVE BEEN MANUFACTURED ACCORDING TO SPECIFICATIONS. AS A RESULT, A REDUCTION IN BRAKING PERFORMANCE AT THE AFFECTED REAR WHEEL COULD OCCUR.

Risk: IN AN EXTREME CASE, THE AFFECTED REAR BRAKE DISC COULD BREAK RESULTING IN A LOSS OF BRAKING AT THAT WHEEL INCREASING STOPPING DISTANCES AND THE RISK OF A CRASH.

Remedy: BMW WILL NOTIFY OWNERS AND WILL REPAIR THE VEHICLES BY INSPECTING THE REAR BRAKE DISCS AND, IF NECESSARY, REPLACE THEM FREE OF CHARGE. THE SAFETY RECALL BEGAN ON SEPTEMBER 11, 2009. OWNERS MAY CONTACT BMW CUSTOMER RELATIONS AND SERVICES TOLL-FREE AT 1-800-525-7417.

We could not check this: model year. The authority's notice

A12/00042/20Safety recallInjuriesno date · EU Safety Gate

The four ISOFIX child-seat attachment brackets on the rear seats may not have the necessary structural durability. As a result, one or more of the brackets could break under increased fatigue loading during operation. This may increase the risk of injury in the event of an accident.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

We could not check this: model year. The authority's notice

A12/00783/23Safety recallInjuriesno date · EU Safety Gate

The airbag propellant may deteriorate over time, and If deployed, excessive internal pressure may cause the inflator body to burst and metal fragments could pass through the cushion material causing injury to occupants. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

We could not check this: model year. The authority's notice

A12/01261/21Safety recallFireno date · EU Safety Gate

Friction corrosion on the connector from the wiring harness to the blower regulator may cause fluctuations in the electrical resistance, which can lead to overheating and damage to the wiring harness insulation. That can result in a short circuit, leading to a vehicle fire, even if the vehicle is parked.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

We could not check this: model year. The authority's notice

A12/01382/23Safety recallInjuriesno date · EU Safety Gate

The driver or passenger airbag inflator may malfunction. In the event of an airbag activation this can lead to the release of fragments from the generator housing, increasing the risk of injury. The product does not comply with the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.

Remedy: Type of economic operator taking notified measure(s): Manufacturer Category of measure(s): Recall of the product from end users Date of entry into force: Unknown

We could not check this: model year. The authority's notice

Engine and transmission

2 engines · 4 transmissions

N54B30

225–250 kW (306–340 HP) · petrol

ZF6HP-BMW · 6-speed automatic, longitudinal (ZF 6HP19/21, BMW GA6HP)

automatic · 6 speed

Torque limit450 Nm
MakerZF

We built the code from the model and the gear count. The factory sheet does not state it. More than one engine code is possible. The fault list shows the faults of each. More than one transmission is possible. The gear count does not tell them apart. The code is on the side of the transmission.

Variant data

What is in this version

Factory data

Trim
X6 xDrive35i Executive
Body
SUV
Fuel
petrol
Transmission
automatic
Engine size
2979 cc
Power
225 kW (306 HP)
Drive
AWD
Production
2008–2012

Factory service interval

The manufacturer specifies this for this version. Of the mileage and the time, the one that comes first is the one that counts.

  • Air filter

    • 60,000 km or 4 years

  • Cabin (pollen) filter

    • 30,000 km or 2 years

  • Brake fluid change

    • first: 3 years, then 2 years(first change at 3 years, then every two years)

  • Engine oil and oil filter (BMW condition-based service)

    • LongLife25,000 km or 2 years

  • Automatic gearbox oil (ZF 8HP / 6HP)

    • 160,000 km

  • Spark plugs, petrol

    • 60,000 km or 6 years
All E71 versions

Information, not an expert opinion

We write the descriptions, and we put the source next to them. A person reviews them before they go out. They are still information, not a technical expert opinion.

  • A fault on the list does not mean the car you are looking at has it.
  • A fault missing from the list does not mean the model is fault-free. Write-ups are made model by model. Not all of them are done.
  • You decide whether to buy. This is no substitute for an inspection. That needs a workshop and a history check.
Details in the terms